Filter Results By:
Products
Applications
Manufacturers
XLR
circular connector found in stage lighting, video and audio equipment.
-
product
everyday measurement microphone
cm-20
An excellent everyday, budget measurement microphone with commendable frequency response for its price. The CM-20 is a " back electret condenser microphone with omni-direction pickup, phantom powered and XLR connector. Rugged construction is part of its appeal. At this price, now you can afford to have a spare.
-
product
Known impedance for use in loudspeaker measurements
Impedance Box
An impedance box is necessary for measuring the impedance of a loudspeaker. Listen Inc.’s impedance box contains a 0.25Ω resistance. This value is suitable for most loudspeakers, but may be easily swapped out for a different value by the user if speakers with a particularly high or low impedance are being tested. It is available with either XLR or 1/4″ balanced connectors. Please specify type of connectors when ordering.
-
product
mAEStro Audio Digital to Analog Converter
The mAEStro ADAC-100 receives AES/EBU (AES3) or S/PDIF digital audio and converts it to two channels of analog audio. It automatically detects sample rates up to 96kHz with low-jitter clock recovery. Two balanced line-level audio outputs are provided on XLR connectors on the rear panel. For convenient monitoring, a stereo headphone mini-jack and volume control are provided on the front panel.
-
product
Microphones
All these measurement microphones have a XLR connector and require a phantom power. They can be connected to specially equipped soundcards or pre-amplifiers, only.
-
product
Plug-On Transmitter
DPR
This unique plug-on transmitter design will ideally match any microphone or line level source via a standard XLR connector. The DPR can tune in 100 kHz or 25 kHz steps across the UHF television band from 470.100 to 607.950 MHz, with a selectable output power of 25 or 50 mW. The purely digital architecture utilizes AES 256-CTR encryption for high level security applications.
-
product
Plug-On Transmitter
HMa
This unique plug-on transmitter design will ideally match any microphone or line level source via a standard XLR connector. Phantom power is selectable at 5, 15 and 48 volts, or can be turned off for use with dynamic microphones and line level signal sources.
-
product
Precision Pink Noise Generator
Noise Plug
The NOISE PLUG is a complete precision pink noise generator built in a XLR microphone connector. Inside the NOISE PLUG is an ultra wideband, avalanche junction white noise source.
-
product
replacement microphone
cm-10
Replacement calibrated microphone for all models of the SA-305X and the Iasys. Models include the SA-3050, SA-3050A, SA-3051, SA-3052, SA-3052A, SA-3055, Iasys and Iasys HT. This is a back electret measurement microphone with calibrated internal preamp. Maximum SPL is 135 dB. Ships complete with 20 foot XLR mic cable and zippered storage bag.
-
product
Cable Testers
E447
Similar to E445 but without jack and RCA (phono) testing facilities. Includes special XLR remote unit to enable testing of cables where it is not possible to bring both ends to the tester.
-
product
8 Plug Pro Audio Cable Tester
PCT10
Enables quick convenient continuity cable testing for all type of cablesLED's confirm each conductor continuity and connection6-Way Switch for selecting connections to be testedIncludes internal battery and ground connection status checkRugged, compact, metal construction for long life and reliabilityTests cables with all types combinations of the following connections3.5mm TRS Jack1/4' TRS Jacks3 Pin XLR Male3 Pin XLR FemaleRCA Phono4 Pin SpeakonBanana Plugs9V Batter (Not Included)
-
product
NL4 / NL8 / RJ45 / XLR TESTER
SC48RJ
Whirlwind Music Distributors, Inc.
The SC48RJ Tester provides rapid, positive testing for NL4 and NL8 type multiline speaker cables, RJ45 type data cables and XLR cables.
-
product
Hematology Analyzer
Pentra 80 Range
Malaria testing is optionally available on ABX Pentra XL 80 and Pentra XLR upon request towards your HORIBA Medical representative.*This product may not be available in your country or region at this time. Please contact your HORIBA Medical sales representative or distributor for more information.
-
product
XLR Barrel Version of the same Switchable Soft-Clip Limiter
Over-Killer
An Over-Killer is an XLR barrel version of the same switchable soft-clip limiter found on our revered audio interfaces. Designed to get more out of your digital copy by allowing you to push levels while limiting the level of a balanced analogue signal to +18dBu.
-
product
PXI Single 10 Channel MUX, XLR Connectors
40-735-902-S2
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
