- Pickering Interfaces Inc.
product
PXI 8 Slot BRIC 60x32 1-Pole (12 sub-cards)
40-562A-121-60X32
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
RACK SYSTEMS
Most of ETL's sub-systems are designed to fit standard 19" racks. We produce RF distribution equipment for a wide range of applications in the RF chain. On satellite downlinks this is between the LNB and the modem or receiver; and on satellite uplinks it is between a modem and a BUC.Reliability, Resilience and RF performance are designed into all our equipment wherever possible. Scaleability and Adaptability also influence the design process.The main product families are shown below, with further selection of products via functionality and design.
-
product
Mezzanine System
5041
ECM P/N 5041 provides eight channels of RS485 / RS422 I/O with fixed 120 ohm termination for each channel. Speeds are up to 30M bits per second. All channels power up as inputs. Also transceiver inputs are always enabled for loop back diagnostic use when the outputs are enabled. Software can enable outputs on a channel by channel basis.
-
product
Probe System
Acculogic FLS 980 Dxi
Flying Probe systems do not require test fixtures, have few restrictions on board access and can test boards with a virtually unlimited number of networks. They also allow developers to complete test programs in a short time.The FLS980 Dxi guarantees superior probing precision and repeatability, even as component sizes and denser packaging technologies pose challenges to other test engineers.
-
-
product
Carrier with System Management
EnsembleSeries™ CCM3011
*OpenVPX carrier module designed to use the Data Plane*PCI/PCI-X interface at up tof 133 MHz on each site*x8, x4 and x1 PCIe interfaces*Advanced OpenVPX system management functionality enables remote monitoring, alarm management, and hardware revision and health management*Conduction-cooled and air-cooled variants available
-
product
Custom Test Systems
ATE Systems has developed a wide variety of custom test systems that integrate commercial test instruments and custom hardware, tied together with a test executive. Examples of the types of tests that have been incorporated include: S-parameters (gain, return loss, VSWR, etc), Noise figure, Power, Spectral response, Linearity, Voltage, Current, Switching speed and so on
-
product
Mezzanine System
5147
ECM P/N 5147 provides two channels of 12 bit A/D conversion using the Analog Devices AD9235, and is suitable for medium resolution high speed applications. The two differential inputs are terminated in 120 ohms and buffered with a gain of 1 differential amplifier. Differential Input range is +/-3.0V. Sample rates are 20MHz per channel with a 5MHz 4 pole elliptical analog input filter.
-
product
Probe System
Acculogic Sprint 4510
The Sprint 4510 family of flying probers are well known for their speed, reliability, ease of use and large world-wide installed base.Flying probe testers have few restrictions on access, require no test fixtures, and can test boards with virtually unlimited number of nets, allowing test developers to turn a program around in a short time.
-
product
Dip Coating Systems
SCS Dip Coating systems, which are available in free-standing floor or tabletop models, are specifically designed for production applications that do not require large in-line systems. SCS dip coating systems can be used to apply a range of coatings, as well as photo-resists and solder masks, that are part of printed circuit board applications all with a level of precision that manufacturer's demand. Both SCS models include a host of features that make them an ideal choice for lab and production operations.
-
product
Probe Based Systems
The integration of additional measurement technology in probers enables you to flexibly expand the analysis options in the ongoing production process. With the introduction of our Automation Assistant software platform, we have therefore equipped a large number of probers with a wide variety of analysis tools.
-
product
Small Unmanned Aircraft System
Aerosonde®
Designed for expeditionary land- and sea-based operations and equipped for simultaneous day/night full-motion video, communications relay, signals intelligence and a customer-selected payload in a single flight, Textron Systems' Aerosonde Small Unmanned Aircraft System (SUAS) delivers reliable, multi-mission performance in a class by itself. It is field-proven with more than 500,000 flight hours, including desert heat and Arctic cold.
-
product
Modular Test System
DMT
The DMT Tester is a modular test system that allows rapid measurement of electrical and non-electrical parameters of functional units. The system also allows basic ICT measurement with optional accessories. It is conceived as modular, with the possibility of integrating a wide range of own and external instruments. The DMT tester is controlled by its own SCADUS software.
-
product
Industrial Damper Systems
1206
The 1206 Industrial Damper System has proven itself in the paper industry for over 15 years in North America and Europe. An Industrial Damper is placed against each end of a calendar roll or yankee roll where the normal roll position presses the damper piston to half of its 1.75 in stroke. Machine users report decreases in resonant vibration which has allowed machine speeds to be increased by up to 30%. The 1206 Industrial Damper System will decrease machine vibration and allow increased through...show more -
product
Mezzanine System Carrier
MMS8010 / MMS8011
The Abaco ECM 3U VPX carrier supports up to six Abaco Systems Electrical Conversion Modules (ECMs) in a VITA 46 VPX form factor. Each ECM site connects 32 single-ended 3.3 V signals to the FPGA. The specific ECM board installed on a site converts the FPGA signals to 16 I/O signals, for a total of 96 I/O signals across the six ECM sites.
-
product
Standard Test Systems
WaveCore™ Products
Textron Systems’ WaveCore family offers a variety of standard test systems with a primary application of satellite payload lab testing. Our systems can be deployed affordably for both production and engineering applications, providing industry-leading levels of data correlation with high system mean time between failures and low mean time to repair.
-
product
Build-to-Print for Test Systems
Built-to-print / test system replication addresses your internal capacity and capability constraints. Ball Systems has perfected quoting, procurement, planning, assembly, testing, quality, delivery and installation to ensure your testers are on-time and on-budget, and meet design and production standards while keeping open and transparent communication.
-
product
Ionic Contamination Test System
Omegameter SMD 650
The SCS Omegameter SMD 650, the long-time industry standard for ionic testing utilizing “static test” methodology, is designed to perform cleanliness testing on printed circuits and assemblies. Identifies the presence of ionic contamination on bare and assembled printed circuit boards and other electronic components. Provides an accurate and repeatable method for determining cleanliness on site. Provides immediate process control results, eliminating the need for outside laboratory testing.
-
product
Integrated Systems
Power, flexible and based on commercial open standards, Integrated Systems from Abaco are pre-integrated and pre-qualified, so they're ready for immediate deployment - minimizing cost, risks and program lead time.
-
product
Wide Band Gap Production System
Reedholm has configured an integrated system, not just a set of boxes, for testing high power devices at the wafer level. Sophisticated testing, prober control, and database management do not carry a programming burden. As a result, fast, automated wafer testing is done in an inexpensive, compact probing platform.
-
product
Ground Threat Emitter Sensor System
GTESS
The Ground Threat Emitter Sensor System (GTESS) is a modular test and training system capable of stimulating multi-spectral aircraft electro-optic sensor suites at long range. The GTESS system integrates Textron Systems’ ultraviolet (Mallina™), infrared (Phoenix) and/or laser (Phantom™) ranged stimulators with an automated tracking system to facilitate fast-moving test, training and evaluation exercises. A fully integrated camera system for effective after action review. GTESS can also work in conjunction with Textron’s radio frequency (RF) range stimulator systems (PRTS™ & HPRTS) for complete multi-spectral testing.
-
product
Midi Systems
MIDI systems provide an efficient solution for customers seeking a Box PC with wide temperature performance and abundant I/O. MIDI systems feature expansion-ready front panels with removable cover plates to expose additional connector cutouts. The enclosure can easily accommodate up to two additional PC/104 style I/O modules or PCIe MiniCards. The cover plate provides ample cooling for our rugged conduction-cooled SBCs. Table-top, wall mount, and DIN rail mounting options are all included.
-
product
Mezzanine System
5174
The 5174 provides two major functions, serving as a precision Voltage Controlled oscillator board and a variable frequency source board. These features can be use together or independently. As a variable frequency source, the 5174 provides a high-resolution variable clock source that is based upon a reference clock supplied by the ECM carrier.
-
product
Defined CRPA Test System
BroadSim Wavefront Software
Protecting your GNSS systems from jamming and spoofing is more critical now than ever before. BroadSim Wavefront was designed to enable easier and more affordable CRPA receiver testing, leveraging proven software-defined architecture.
-
product
Gated IF RCS Systems
Innovative Technical Systems has designed many instrumentation systems for radar cross section (RCS) measurements. Some of the designs are based around standard network analyzers for signal processing, while utilizing high PRF short-pulse RF transceivers with gated IF architecture. The modular design approach uses separate transmitter and receiver modules for monostatic or bistatic measurements. Compact module design provides flexibility to mount the transmitters and receivers close to the ante...show more -
product
Automated Test Systems
Chroma Systems Solutions, Inc.
From power conversion to battery to electrical safety, our test systems will maximize your time, improve your validation process, and increase your throughput.
-
product
Function Test Systems
These specialist Automeg models test the function and integrity of wiring harnesses combined with active components such as relays, switches, contactors, diodes, LEDS, actuators and other active components.Our software takes the complex and traditionally long task of creating functional tests away from the test engineer and allows these to be created automatically, from existing ECAD data and our component library and automated software routines. All the different routes and subtests are automatically calculated in seconds.
-
product
Very Broadband Borehole Systems
Borehole installations offer excellent performance for low-noise detection of weak seismic signals such as from local microseismic events or from regional/teleseismic earthquakes.
-
-
product
Mezzanine System
5085
ECM P/N 5085 provides two channels of 24 bit A/D conversion suitable for high resolution low speed applications, which include bridge circuits, thermocouples, RTD and voltage measurements. For bridge applications each channel provides a fused +5 Volt or a current source drive.
-
product
Enhanced Vision Systems
Elbit Systems of America’s Degraded Visual Environment (DVE) solution uses intuitive 3D grid symbology along with a helmet tracker to provide critical helicopter/tilt-rotor cues during brownout operations. This system, which is an upgrade to the head-up display installed on many military helicopters, removes weight or drag penalties by eliminating nose-mounted sensors. The helmet tracker provides numerous ancillary benefits such as depicting the other pilot’s Line of Sight (LOS) for improved crew coordination, as well as providing the ability to slew weapons or optical payloads to the pilot’s LOS, hands-free and heads-up.
