Filter Results By:
Products
Applications
Manufacturers
-
product
Circbord
8002
VECTOR Electronics and Technology, Inc.
Interleaved buses pattern, ideal for wire-wrap applications. Power and ground buses etched onto wiring side only. Bus surfaces solder coated for user convenience. Mount components with 0.3”, 0.6” & 0.9” lead spacing.I/O area with square solder pads for connector mounting. Single-sided with no etch and plating on reverse side.
-
product
Circbord
8007
VECTOR Electronics and Technology, Inc.
Pad-Per-Hole pattern on component side. Overall Ground Plane pattern on wiring side.0.080” diameter isolated solder pad around holes oncomponent side. Plane surfaces solder coated for user convenience.
-
product
Circuit Tracer, Inductive Clamp
61-958
*Induces a signal in a conductor*1 in. jaw opening/6 ft. cord*Works on de-energized circuits and energized circuits up to 5A, also low voltage wiring and metal conduit*Powered solely by a separate battery pack (supplied with 8 C-cell batteries)
-
product
Compact Differential Pressure Transmitters
Series 668B/D
Our low cost SERIES 668B/D Compact Differential Pressure Transmitters are capable of sensing differential gage pressure with ±0.8% FS accuracy, and converts this pressure difference to a proportional high level analog output for both unidirectional and bi-directional pressure ranges. These transmitters can withstand up to 15 psig overpressure with no damage to the unit. The compact, lightweight design makes installation simple and easy. Units are protected against incorrect wiring, and include a protective terminal cover.
-
product
Contactors
Mitsubishi Electric Automation, Inc
Compact dimensions, modular expansion options and a power-saving design are the key characteristics of the MS-N and MS-T series magnetic contactors. DIN rail mountable and standardized terminal covers make installation and wiring user friendly and cost effective.
-
product
Custom Wiring Harnesses and Cables
From flight critical aerospace wiring harnesses to discrete wire assemblies, WinSoft can meet your toughest requirements. Each of our finished cable assemblies and wire harnesses is built to the customer exact specifications and is 100% quality tested. Cable and harness assemblies are certified to meet all customer requirements and applicable industry standards while manufactured to strict ISO processes and procedures.
-
product
Defect Detection
StarProd LTB
The StarProd LTB is a unique defect detection bench for linear array antennas such as BTS. Tests performed on this bench instantly identify defects such as flawed or absent soldering, swapped wiring or short circuits. Results provide information on the position and type of any existing error. Operators can then immediately step in to make corrections knowing precisely how and where they are needed. StarProd LTB also performs tilt computations which can reveal a misconfiguration, or a mechanical or RF component defect. The end result: improved production processes and product quality.
-
product
DIN Backplane
VECTOR Electronics and Technology, Inc.
Universal (uncommitted) multilayer backplanes are designed for unique one of a kind applications requiring custom pin-out wiring from connector to connector. Each individual connector pin must be "assigned" by connecting to adjacent power or ground pins with wire or jumpers. Power or Ground input through a labeled series of power taps (screw terminals) along to top and bottom of the board.
-
product
DIP-ER™ Logic Jumper
Series 115, 116, & 117
DIP-ER Logic Jumper. Reliable, electronically tested solder connections. Protective covers are ultrasonically welded on and provide strain relief for cables. DIP-ER Logic jumper wiring is point to point. Consult factory for other wiring needs.
-
product
DIP Jumpers
Series 100 thru 111
DIP Jumpers. Aries offers a wide array of DIP jumper configurations and wiring possibilities for all your programming needs. Protective covers are ultrasonically welded on and provide strain relief for cables. 10-color cable allows for easy identification and tracing.
-
product
DrivePro Remote Ultimate
Benefit from the ability to share live vehicle data, receive complete OEM repair information, wiring diagrams and more directly through the DrivePro Remote Unlimited diagnostic support platform.
-
product
Earth Leakage Circuit Breakers
Mitsubishi Electric Automation, Inc
Like molded case circuit breakers, these circuit breakers are utilized to open/close low-voltage circuits and protect wiring by automatically closing circuits when they''re overloaded or if a short-circuit occurs. We offer a comprehensive range of circuit breakers that provide superior performance in electrical protection, isolation and power distribution applications. Our circuit breaker products comply with various standards such as JIS, IEC, EN, GB and UL/CSA, and with easy to install accesories, the Mitsubishi Electric circuit breakers are "user-friendly" and ensure the best solution for virtually every application.
-
product
Energy Meters
Contrel Elettronica s.r.l. Company
Energy meters for efficient management of energy consumption. Total and partial energy meters (resettable). Equipped with input / output and communication module. From direct single-phase connection in a single module to three-phase wiring via CT. High precision. MID versions: certified energy meters for sub-measurement.
-
product
Ethernet Motion Controllers
DMC-21x3
Galil's DMC-21x3 Ethernet motion controllers are designed for extremely cost-sensitive and space-sensitive applications. These controllers are typically half-the-price and half-the-size of box-level Ethernet controllers. These intelligent, card-level controllers can be purchased with plug-in, multi-axis amplifier boards which eliminate wiring between the controller and drives.
-
product
Ethernet To Parallel Digital Interface Boards
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
product
Ethernet to Relay Interface Boards
Model 8064 OEM
* 115631-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully VXI-11 compliant.* Easy configuration with any web browser.* Includes 50-pin mating connector for solder connections.* Optional terminal board for easy connections without soldering. See the Ethernet Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS Wiring Kit to connect to an RJ45 connector on the rear panel.
-
product
Eurocard Plugbord
4614-3
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. Pad-Per-Hole both sides. Voltage and ground bus around board perimeter on both sides. For solder, Wire-Wrap or mixed wiring methods. Pad and bus surfaces solder-coated for user convenience. Row and column legends provided.
-
product
Eurocard Plugbord
E160-6U-2
VECTOR Electronics and Technology, Inc.
6U x 160mm Eurocard size for 96-pin DIN connectors.Voltage and ground bus around board perimeter on both sides. Bus surfaces solder coated for user convenience. For solder, Wire-Wrap or mixed wiring methods.Row and column legends provided.
-
product
Eurocard Plugbord
4614-4
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. Pad-Per-Hole both sides Voltage and ground bus around board perimeter on both sides For solder, Wire-Wrap or mixed wiring methods Pad and bus surfaces solder-coated for user convenience Row and column legends provided
-
product
Eurocard Plugbord
E220-6U-1
VECTOR Electronics and Technology, Inc.
6U x 220mm Eurocard size for 96-pin DIN connectors. Pad-Per-Hole both sides. Voltage and ground buses around board perimeter on both sides. Pad and bus surfaces solder coated for user convenience.For solder, Wire-Wrap or mixed wiring methods. Row and column legends provided.
-
product
Eurocard Plugbord
E160-3U-2
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. Voltage and ground buses around board perimeter on both sides. Bus surfaces solder coated for user convenience.For solder, Wire-Wrap or mixed wiring methods. Row and column legends provided.
-
product
Eurocard Plugbord
E160-3U-1
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. Pad-Per-Hole both sides. Voltage and ground buses around board perimeter on both sides. Pad and bus surfaces solder coated for user convenience. For solder, Wire-Wrap or mixed wiring methods.Row and column legends provided.
-
product
Eurocard Plugbord
E220-6U-2
VECTOR Electronics and Technology, Inc.
6U x 220mm Eurocard size for 96-pin DIN connectors. Voltage and ground buses around board perimeter on both sides. Bus surfaces solder coated for user convenience. For solder, Wire-Wrap or mixed wiring methods. Row and column legends provided.
-
product
Eurocard Plugbord
E160-6U-1
VECTOR Electronics and Technology, Inc.
6U x 160mm Eurocard size for 96-pin DIN connectors. Pad-Per-Hole both sides. Voltage and ground buses around board perimeter on both sides.Pad and bus surfaces solder coated for user convenience. For solder, Wire-Wrap or mixed wiring methods.Row and column legends provided.
-
product
Fieldbus ComTool
FBT-9
he Relcom Fieldbus ComTool (FBT-9) establishes communications among Foundation Fieldbus devices without a DCS allowing early checkout of wiring and devices.
-
product
Fixed Mounting Panel, G2, 5U, 3 Position, (2 Blank Plates Included)
310113395
The 19" rack mounting panel offers three mounting positions for the G2 receiver without the hinging feature and is beneficial in cases where you may want to restrict wiring or instrument access.
-
product
Functional Test Fixtures
Test Head Engineering's Custom Functional Test Fixtures range from simple to extremely complex. Typically, our customers do their own wiring and programming, but we will complete the job right up to the customer's requirements, including offering turn-key control and test programming through our partners.
-
product
G12x Slide Mount
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common rack depths. The G12x uses the same platform and slides as the G12, providing support up to 180 lbs (81 kg) to accommodate the largest fixtures. G12x accepts ITAs designed for both the G12 and G12x.
-
product
Harness Test Fixtures
Doyle Test Fixtures for the manufacturing of Electrical Wiring Harnesses or Assemblies.
-
product
High Density 68 pin
HDEterm68
The high density 68 pin SCSI II/III connector is being used for purposes other than SCSI interfaces because of board and front panel space limitations. For example in the PMC environment the SCSI connector provides an excellent size and pin count for the front panel space allowed. The SCSI connector while dense, is not easy to connect to with wiring intended to go to multiple locations
