Filter Results By:
Products
Applications
Manufacturers
-
product
Chart Recorder and Data Acquisition
MRC8000
The MRC 8000 incorporates numerous refinements over its 10½ MRC 7000™ sibling, including a larger 12 inch recording area; an advanced platen assembly which eliminates slide wire feedback for improved reliability; as well as the incorporation of optional isolated 4–20mA outputs to provide the highest resolution and accuracy available in a recorder of this type.
-
product
Circbord
8019-1
VECTOR Electronics and Technology, Inc.
Single sided board, circuit pattern one side only, holes not plated thru.Ideal for common busses, signal line running longer distances, for hard wire of test circuits or discrete components. Tracks run close to board edges. 3U X 160mm Eurocard size will fit into 3U DIN Metric subrack.
-
product
Circbord
8022-180
VECTOR Electronics and Technology, Inc.
FR4 Hi-Tg, 180°C Material, single sided board, circuit pattern one side only, holes not plated thru.Ideal for common busses, signal line running longer distances, for hard wire of test circuits or discrete components.Tracks run close to board edges.
-
product
Circbord
8022
VECTOR Electronics and Technology, Inc.
Single sided board, circuit pattern one side only, holes not plated thru.Ideal for common busses, signal line running longer distances, for hard wire of test circuits or discrete components. Tracks run close to board edges.
-
product
Circbord
8019
VECTOR Electronics and Technology, Inc.
2-sided board, circuit pattern on both sides, holes plated thruIdeal for common busses, signal line running longer distances, for hard wire of test circuits or discrete components. Tracks run close to board edges. Solder coated pattern on both sides of board. 3U X 160mm Eurocard size will fit into 3U DIN Metric subrack.
-
product
Circuit Breaker Finder Accessory Kit
69411
For use with ET300 Digital Circuit Breaker Finder.Light socket adapter for finding the correct circuit of a lighting fixture.Alligator clip adapter enables use of on bare wires.
-
product
Circuit Tracer Open/Closed
SureTrace™ 955
Receiver display rotates automatically for easy viewingIdentifies breakers and fuses with CertainCircuit™ detection*Pinpoints open and shorts*Traces wires*0-99 display of signal strength*Audible indication intensifies in tone/pitch with signal strength*Works on energized or de-energized circuits (0-600V AC/DC)*Four sensitivity levels*Peak reading bar graph*2-year warranty
-
product
Clamp Multimeters
Clamp meters test AC/DC voltage, DC voltage, resistance and continuity. Measure conductors at any point in the wire or cable.
-
product
Configurable Thermocouple Transmitter
HD778TR1
Configurable 4...20 mA/20...4 mA 2 wire temperature transmitter for K, J, T, N thermocouples.
-
product
Copper TAPs
Profitap Copper TAPs provide complete access and visibility into your network by creating an exact copy of full-duplex 10M/100M/1G/10G traffic at wire speed with no impact to the network link. Profitap Copper TAPs introduce no point of failure to the network. They are designed for redundant powering, which allows a second power supply to activate if the first were to become unavailable. In case of complete power loss, Profitap Copper TAPs guarantee that the link remains operational by instantly switching to a fully passive mode.
-
product
Coupling Decoupling Network for Communication Lines
CDN61000-5C
• Application Range: ≤4kV, 1.2/50us pulse, 8 wire unshielded twisted pair (UTP) • Test Voltage: Max 4KV, 2 kV (1.2/50 µs pulse when RJ45 connector is connected. Maximum test voltage is 1.5kV when RJ45 female is unconnected or auxiliary terminal is not protected.) • Coupling mode: 90V gas- discharge tube+250ohm Resistor/Each Wire, 8 Wires Simultaneously-Ground (Common Mode) • Input and output interface: RJ45 connector • Terminal layout (RJ45 connector): First pair of lines: pins 1/2 Second pair of lines: pins3/6 Third pair of lines: pins 4/5 Fourth pair of lines: pins 7/8 • Max. operating speed: 1000MBit/s • Max operating voltage: Max 50V DC • Max operating current: Max 1A Related Instruments
-
product
Current Sensors
Our current sensors were designed for a simple, customer-specific construction of niobium wire wound magnetometers, gradiometers or preamplifiers for small current or voltage signals.
-
product
Current Transformers
The Current Transformer (CT) is the sensor which measures the amount of current draw from the wire it is installed on.
-
product
Custom Wiring Harnesses and Cables
From flight critical aerospace wiring harnesses to discrete wire assemblies, WinSoft can meet your toughest requirements. Each of our finished cable assemblies and wire harnesses is built to the customer exact specifications and is 100% quality tested. Cable and harness assemblies are certified to meet all customer requirements and applicable industry standards while manufactured to strict ISO processes and procedures.
-
product
Demagnetize Bar Tube Or Wire Material Ranging Up To 8.5” (215mm) Diameter During Production
Demagnetizers
*Offers effective demagnetizing even for problem alloys.*Used in metal manufacturing plants to eliminate residual magnetism in test material after the eddy current test (ECT) is completed.*Can also be used for similar applications where high-speed reduction of residual magnetism is required.*Several models are available to meet your unique production needs.*Experienced MAC® Field Engineers can recommend the most appropriate demagnetizing equipment for your applications.
-
product
Diaphragm Pressure Switch
CS & CD
Series CS and CD combine advanced design and precision construction in a small size. Unit is ideal for instrument panels, small compressors and general industrial applications. Visible set point and easy to wire SPDT snap switch reduce installation time. Operates in any position and is vibration resistant.
-
product
Differential Pressure Transmitter
608
The Dwyer Series 608 Differential Pressure Transmitters convert positive, negative (vacuum), or differential pressures of clean, dry air or other non-conductive, non-corrosive gases into a standard two wire, 4-20 mA output signal
-
product
Digital Clamp Meter
A clamp meter is convenient for measuring instruments that allows the measurement of current simply by clamping a wire while being energized without cutting a circuit. In cases of measurement by a multitester and digital multimeter, the circuit must be cut to measure current. In contrast, with a clamp meter, current can be measured simply by clamping a live wire over its sheath. In addition to its simple operation, it allows safe measurement of a higher current.
-
product
Digital Meters
Hoyt Electrical Instrument Works Inc.
It is a compact multifunction instrument which Measures important electrical parameters in 3 phase 4 Wire and 3 phase 3 Wire Network & replaces the multiple analog panel meters
-
product
Digital Termination Boards
MSTB 008
For quick and secure connection of discrete wires to a Data Acquisition Processor (DAP) board, use the MSTB 008 Digital Termination Board.
-
product
Digital Transmission
The physical transfer of data (a digital bit stream or a digitized analog signal[1]) over a point-to-point or point-to-multipoint communication channel. Examples of such channels are copper wires, optical fibers, wireless communication channels, storage media and computer buses. The data are represented as an electromagnetic signal, such as an electrical voltage, radiowave, microwave, or infrared signal.
-
product
DIN Backplane
VECTOR Electronics and Technology, Inc.
Universal (uncommitted) multilayer backplanes are designed for unique one of a kind applications requiring custom pin-out wiring from connector to connector. Each individual connector pin must be "assigned" by connecting to adjacent power or ground pins with wire or jumpers. Power or Ground input through a labeled series of power taps (screw terminals) along to top and bottom of the board.
-
product
Distance Gauge
LOCalizer
LOCalizerTM from Faxitron® is the revolutionary way to guide breast surgeries easily and accurately. LOCalizer uses a miniature radiofrequency Tag designed to be implanted into the breast up to 30 days before surgery. No surgical wires mean less stress for your patients and no more localization scheduling conflicts for you and your team. LOCalizer gives you the precision you need without the drawbacks of other localization techniques.
-
product
Draw Wire Sensors
Draw wire sensors offer a simple solution to measure linear speed and position. Utilizing a flexible cable, a spring-loaded spool, and a sensor (an optical encoder with incremental, absolute, analog or potentiometric output), draw wire sensors can precisely measure linear position. Draw wire sensors do not need precise linear guidance and are ideal for wet, dirty, or outdoor environments and applications where your measuring range travels over harsh environments. These include applications in iron, steel, and wood (saw mills, joineries).
-
product
Drill Chuck Grips
Metal rods, wires, and plates and electronic components can be tensile tested using drill chuck grips. Electronic components are tested by placing the metal legs of the components in the grips, allowing different shaped components to be tested with the same set of grips.
-
product
Drum Core Inductors
Drum core inductors are so named as the conductor (round magnet wire) is wound directly onto the ferrite core which is shaped like a drum or spool. The wire is then connected to the core, a plastic base or metal lead frame to form the surface mount termination. Drum core inductors come in unshielded (high saturation current but potentially more EMI) and shielded constructions (lower saturation current but closed magnetic path for lower EMI). The shielded constructions use either a second ferrite core or a magnetic resin epoxy to create the magnetic shield.
-
product
DSE Wire Testers
DSE Test Solutions your gateway to a world of wire technology.We supply high-quality test equipment for the wire and cable industry. Our extensive range of intelligent test equipment is used for quality control and production optimisation of enamelled wire and cable.
-
product
Dual-Channel Power Supply
DPS16
The DPS16 is a dual-channel power supply with very low output noise and no ripple. The output current can be up to 200 mA and has a programmable current limit. The 4 wire capability provides an excellent load regulation. Because the DPS16 is a fully linear design the output noise is exceptionally low while there are no ripple components as usually seen with switched mode designs. The unit has voltage and current read back on both channels with 16-bit resolution.
-
product
Electrical Heat Shrink Tubing Solutions
TE Connectivity produces Raychem Electrical heat shrink tubing that sets extremely high standards in areas such as insulation, protection, and element proofing. Raychem shrink tubing uses a duplication process that involves a cross-linked material design ensuring cable system's performance. This cross-linked design creates an impenetrable barrier from the elements while simultaneously binding cables and insulating them. The heat shrink process involves tubing that utilizes a thermal influence that causes it to tightly shrink and adhere to a cable. This tight seal is not only ultra-protective, but also flexible, abrasion resistant, and easy to use. This flexible tubing can fit a huge range of cable sizes and specifications. Perfect for various different operations and industrial applications. This includes cables, wires, and even joints.
-
product
Electrodes
EGL electrodes have consistently raised the industry standards for reliability and performance since their introduction in 1930.To ensure rigid quality control, all phases of manufacturing are performed in-house, including emission coating, inverter welding shells with lead wires, and sealing and centering the mounts in glass envelopes.
