-
product
UTP Cable Tester
21-8574-00
The Lan Cable Tester is consists of unshield RJ45:568A, 568B & USOC. The tester also easy to operate, the user begins testing by connecting. The multiple LEDs showed indication. This Lan Cable Tester is very practical tester can be easily read and correct pin configuration of cable continuity, open, short, miswiring, & no connection.
-
product
UTP Software Suite
Increasing customer requirements, shorter product cycles and higher time to market demands dramatically influence the long-term goals in software development. With the Universal Test Platform Software Suite (UTP Suite), we introduce a robust standard that features a great set of tools for configuring, developing, analyzing, debugging and executing test sequences.
-
product
4x4 VGA + Audio Matrix Switch with UTP Output and IP Control
VSM-I-A-4-JA4
Switch up to 4 VGA inputs to 4 VGA outputs with independent audio routing. Additional RJ45 output connectors provide extended output up to 1000 ft (305 m) over a single UTP cable (with compatible URA receivers). 550 MHz bandwidth supports resolutions beyond 1920x1200.
-
product
VTAC Patchcord, Receiver, 36", VTAC, 2x 1000Base-T1 UTP Wire 1 Port MateNet, 1 Position
7-142716763-036
VTAC Patchcord, Receiver, 36", VTAC, 2x 1000Base-T1 UTP wire 1 Port MateNet, 1 Position.
-
product
VTAC Patchcord, Receiver, 36", VTAC, 2x 1000Base-T1 UTP Wire H-MTD Cable Jack, 1 Position
7-142716765-036
VTAC Patchcord, Receiver, 36", VTAC, 2x 1000Base-T1 UTP wire H-MTD Cable Jack, 1 Position.
-
product
VTAC Patchcord, Receiver, 72", VTAC, 2x 1000Base-T1 UTP wire H-MTD Cable Jack, 1 Slot
7-142716765-072
VTAC Patchcord, Receiver, 72", VTAC, 2x 1000Base-T1 UTP wire H-MTD Cable Jack, 1 Slot.Note: Static Bend Radius - 19.2mm [.76in], Flex Bend Radius - 48mm [1.89in]
-
product
Hand-held Cable Tester
STM-8
The STM-8 is an economical and versatile hand-held tester designed for the testing of UTP and screened cable for opens, shorts, reversals, miswires, split pairs and cable length.
-
product
IVN-8561, Automotive Ethernet Interface Device
786169-01
2-Channel, 4-Port, 100BASE-T1 to 100BASE-TX Automotive Ethernet Interface Device—The IVN-8561 is an interface that converts 100BASE-T1 unshielded twisted pair (UTP) automotive Ethernet to standard 100BASE-TX Ethernet. It is ideal for developing applications that require automotive Ethernet to test and validate automotive electronic control units (ECUs). The IVN-8561 provides two channels to convert data between 100BASE-TX Ethernet and 100BASE-T1 Automotive Ethernet. Each 100BASE-T1 port can be configured as master or slave, using switches on the front panel. The IVN-8561 also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.
-
product
KIT for Test Cable Networks with Tools and Accessories
1RA370
Include: *Multi network cable tester for RJ45 (UTP / STP) and BNC*Modular crimping tool*LSA insertion tool*Cable stripper and cutter*30 units of RJ45 (8p8c) modular plugs*30 units of RJ11 (6p6c) modular plugs*24 units of colour strain relief*Comonents pocket*Zipper vinyl case
-
product
Lan CAble Testers
TES Electrical Electronic Corp.
Tests a wide range of FTP & UTP cables. Tests for wiring faults such as open, shorted reversed.
-
product
Network Cable Tester
KT-95
Test device with UTP (Unshielded Twisted pair) ,STP (Shielded Twist Pair) and coaxial wiring ; Test with BNC and RJ45 socket. Test cable length, Check wire continuity, open, short, reversal and miswire. Main unit and one remote allow one person operate. Length Test Range:20m/200m/2km/20km Accuracy: À1% rdg À 0.3m. Self Calibrate available
-
product
Parallel Testing of Multiple DUTs with High RF Channel Count
Test Rack UTP 7033 RF for validation
Our basic test rack UTP 7033 (33 rack units) is intended for equipping with various products and therefore for various application areas.The rack shown here as an example is prepared with products and measurement instruments to test automotive devices with high channel count.
-
product
8K ip Camera Tester M-IPC-450C with TVI 5.0 Audio, Wrist Design
M-IPC-450C
Fuzhou Metricu Technology Co Ltd
8K wrist tester M-IPC-450C supports 8K ip camera, analog camera, 8MP TVI camera, 8MP CVI camera and 8MP AHD camera. (5 in one)It also supports DC12V 3A, 48V PoE 25.5W power output, UTP cable, RJ45 TDR cable, RS485, Audio in, TVI 5.0 audio, wrist design, etc.
-
product
Automotive Ethernet Interface Device
The Automotive Ethernet Interface Device converts unshielded twisted pair (UTP) Automotive Ethernet to standard Ethernet. This device is ideal for developing applications that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). It includes ports for Automotive Ethernet connections and ports for 100BASE-TX Ethernet connections. You can use switches on the front panel to configure each 100BASE-T1 port as master or slave. The device also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.
-
product
Cable Management Tools and Testers
For anything compture repair and workstation installation tool, you've come to the right place. C2G carries a variety of cable tools and testers for network, coaxial, electrical, F-type, PC, telephone, and fiber cables. Our crimp tools are also available for RCA, BNC, F-type, RJ45, RJ11, RJ12, and flat ribbon connectors. C2G cable cutting tools can be used to cut a range of wiring types, from RG6 and RG59 coax, speaker wire, UTP network cable, flat ribbon, and more.
-
product
Cable Tester
KT-468
Test device used UTP and STP network wiring and phone line. Check continuity and configuration of wiring with unshielded and shielded modular plugs. Test for open circuits,shorts,miswires and reversals. SHIELD detection tests a cable`s shield integrity. Main unit and one remote allow one person testing
-
product
Cable Tester
KT-200
Test with UTP (Unshielded Twisted Pair) and STP(Shielded Twisted Pair) cable. Check continuity and configuration of wiring with unshield and shielded modular plugs. Test for open circuits, shorts, miswires, reversals, and split pairs. SHIELD detection tests a cable's shield integrity. Test T568A,T568B ,!0 Base-T and Token Ring configurations. Special switch for select symmetric configurations or Non-symmetric cable use for connecting 2 PC.
-
product
Cable Testers
The Tester can check UTP and STP Cat 5E,6,6A and Coaxial Cable. It can ldentify and locate the distance of a open or Short Circuit. With the Multifunction Tester you can determine the Continuity and Wiring of the Cable Pattern. Comes with the Low Battery Indicator. It uses TDR ( Time Domain Reflectometer ) to measure the length and distance of the cable. LCD Backlight Display.There are 8 Remote ID available.
-
product
Car Camera Bus (C2B)
Analog Devices Car Camera Bus (C2B™) is an innovative new camera link technology enabling HD video over Unshielded Twisted Pair (UTP) cables and unshielded connectors. C2B provides an easy upgrade path from SD to HD cameras without the need to change the existing cable and connector infrastructure. C2B enables a camera link with reduced system cost, significant weight savings and increased robustness. The C2B portfolio of transmitter and receiver devices enable seamless camera connectivity in the vehicle. The C2B technology was defined and designed for automotive applications and provides a robust camera link solution for these applications:
-
product
CAT-5 Cable Equalizers
Analog Devices high speed, differential receivers and CAT-5 cable equalizers compensate for the transmission losses of UTP and coaxial cables up to 300 meters in length. Our design techniques for products such as the AD8123 optimize performance for low noise, short-to-medium range applications, while also providing the high gain bandwidth required for long cable equalizations. Various gain stages are summed together to best approximate the inverse frequency response of the cable. Logic circuitry controls the gain functions of the individual stages so that the lowest noise can be achieved at short-to-medium cable lengths.
-
product
CAT-5 Video Drivers
Analog Devices provides designers with a robust portfolio of high speed triple, differential, and single-ended input to differential output CAT-5 video drivers. We designed the technology for the highest resolution component video signals, but it can be used for any type of analog signals or high speed data transmission over either Category 5 UTP cable or differential printed circuit board (PCB) transmission lines. Manufactured with our second generation XFCB bipolar process, the drivers have large signal bandwidths of 700 MHz, fast slew rate, and output amplitude and phase matching balanced to –60 dB at 50 MHz.
-
product
CAT-5 Video Receivers
Analog Devices high speed, differential CAT-5 video receivers and equalizers compensate for the transmission losses of UTP and coaxial cables up to 300 meters in length. Various gain stages are summed together to best approximate the inverse frequency response of the cable. Logic circuitry controls the gain functions of the individual stages so that the lowest noise can be achieved at short-to-medium cable lengths. Our video receivers provide excellent common-mode rejection that enables the use of low cost, unshielded twisted pair cables in noisy environments.
-
product
CATx Surge Protector
SP-CAT5-6V
Protects sensors running on CATx unshielded twisted pair (UTP) cable against the effects of electrostatic discharge, faulty wiring and lightning. The use of two protectors on each end of the line will provide increased protection for each end against surges. Protected pins: (1,2) (3,6) (4,7) and (7,8) pass through. Impedance: 85 to 115 Ohms. Surge suppression: 22Vpeak @ 100A 10/1000µs. Maximum continuous voltage: 6Vpeak. Dimensions WxDxH: 1x3.6x0.9 in (25x91x23 mm). Regulatory approvals: GR 1089, NEC 800.100 and 830.100, ITU 703, UL94 V0 Flame Rated.
-
product
Coupling Decoupling Network for Communication Lines
CDN61000-5C
• Application Range: ≤4kV, 1.2/50us pulse, 8 wire unshielded twisted pair (UTP) • Test Voltage: Max 4KV, 2 kV (1.2/50 µs pulse when RJ45 connector is connected. Maximum test voltage is 1.5kV when RJ45 female is unconnected or auxiliary terminal is not protected.) • Coupling mode: 90V gas- discharge tube+250ohm Resistor/Each Wire, 8 Wires Simultaneously-Ground (Common Mode) • Input and output interface: RJ45 connector • Terminal layout (RJ45 connector): First pair of line...show more -
product
Ethernet Media Converter
A physical layer equipment which interconnects the Ethernet, Fast Ethernet, or Gigabit Ethernet on copper UTP and the related fiber optics network. Ethernet media converter meets corresponding IEEE 802.3 standards.
-
product
Ethernet Media Switch
Ethernet media switch is a layer 2 switch running on Ethernet or Fast Ethernet. It equips with one or two fiber ports and four copper UTP ports and hence acts as easy-to-use add-drop equipment for connecting network devices into optical fiber network. Ethernet media switch meets corresponding IEEE 802.3 standards.
-
product
Function Tester with Low Number of Channels
UTP 6010 RF
The UTP 6010 is one of our smallest test systems and therefore a cost-effective entry into our UTP tester series.The fast system is used to implement scalable functional test applications for a test item (single device under test) with multiple RF channels and mixed-signal test options. Depending on the adapter, the DUT can be tested at circuit board level (FKT) or when installed at the end of the line (EOL).Depending on the test item requirements, we configure the appropriate number of channels...show more -
product
Glass Break Detection Sensor
ENVIROMUX-GBS
Acoustically detects the cracking of glass. Adjustable sensitivity. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D.
-
product
Smoke Detection Sensor - CE Approved
ENVIROMUX-SDS-CE
For warning of smoke. Photoelectric smoke detector. Smoke sensitivity: 0.08-0.14 dB/m. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: 14 to 122°F (-10 to 50°C). Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
product
Smoke Detection Sensor - UL Approved
ENVIROMUX-SDS
For warning of smoke. Photoelectric smoke detector. Smoke sensitivity: 0.98-2.4%/ft. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: 14 to 122°F (-10 to 50°C). Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL, RoHS.
