- Virginia Panel Corporation
product
Signal, Patchcord, Receiver, 36", TriPaddle, USB 2.0 Wire, to USB Type A Plug (1.5 Amps)
7-104872596-036
Signal, Patchcord, Receiver, 36", TriPaddle, USB 2.0 Wire, to USB Type A Plug (1.5 Amps).
-
-
product
MyoWare 2.0 Muscle Sensor
Using our muscles to control things is the way that most of us are accustomed to doing it. We push buttons, pull levers, move joysticks... but what if we could take the buttons, levers and joysticks out of the equation and control it with our muscles? The MyoWare® 2.0 Muscle Sensor is an Arduino-compatible, all-in-one electromyography (EMG) sensor from Advancer Technologies that allows you to do just that! The MyoWare 2.0 Muscle Sensor has been redesigned from the ground up with a new easy-to-us...show more -
product
PCIe 2.0 Test Platform
PXP-100B
The Teledyne LeCroy PXP-100B Test Platform provides a convenient means for testing PCIe 2.0 add-in cards with a self-contained portable and powered passive backplane. The PXP-100B provides power required for both cards under test, and an interposer can be used for connection to a protocol analyzer. As an alternative to an interposer, the PXP-100B includes two mid-bus probe footprints to allow connection to an analyzer via a mid-bus probe.
-
product
Portable Avionics Interfaces for USB 2.0
These versatile interfaces are suitable for a wide range of applications in the lab and in the field. They support maximum data throughput on all channels and have a large 32 MB built-in memory. All power necessary for operation is provided via the single USB port. Plug and Play and Hot Swap features make them easy to install and move between computers.
-
product
USB 2.0 Interface Module
USB 2.0 modules for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for the USB 2.0 link untouched.
-
product
USB 2.0 Protocol Analyzer
Mercury T2
The Mercury T2 is the industry's smallest, most affordable hardware-based USB 2.0 protocol analyzer that combines the defacto standard CATC Trace display with powerful analysis features. The pocket-sized Mercury T2 is bus powered and is controlled using any Windows PC. With comprehensive triggering, the Mercury T2 provides much of the same lab quality protocol analysis capabilities offered in Teledyne LeCroy's top-of-the-line USB analyzers.
-
product
80Gbps Video Analyzer/Generator for DisplayPort 2.0 Testing
M42d
The Teledyne LeCroy quantumdata M42d Video Analyzer/Generator provides functional and will support compliance testing for video, audio and protocol of DisplayPort 2.0 and DisplayPort 1.4. The M42d supports legacy DisplayPort lane rates of 1.62, 2.7, 5.4, 8.1 Gb/s and the new DP 2.0 higher speed lane rates of 10.0, 13.5, & 20.0 Gb/s data rates with the new line coding—128b/132b. The protocol analyzer provides a snap shot status view and deep analysis using captures of incoming DisplayPort 2.0...show more -
product
COMET VISION 2.0
CV
Software for COMET Dataloggers Sxxxx, Rxxxx, UxxxxM, Commeters Dxxxx and Multiloggers Mxxxx.
-
product
PCIe Cable: x8, 2.0 m
Y1202A
Use to connect a PXIe or AXIe chassis to a desktop or rackmount computer.
-
product
8 CANBus Channels, CAN 2.0 A/B Protocol
CB1
The serial bus system with real-time capabilities is the subject of the ISO 11898 International Standard and covers the lowest two layers of the ISO/OSI Reference Model. Our CANBus modules provide independent, isolated channels of CAN serial data bus links, conforming to the ISO 11898 International Standard. All CAN nodes are able to transmit data and several CAN nodes can request the bus simultaneously.
-
product
DisplayPort 2.0 Receiver Test
N5991DP2A
Use the Keysight N5991DP2A DisplayPort 2.0 Receiver Test Software to test, debug and characterize your DisplayPort Sink products maximizing the usage of your test instruments.
-
product
USB4 Version 2.0 Receiver Compliance Test Software
N5991U42A
N5991U42A is the receiver compliance test automation software, allowing you to test and characterize USB4 Version 2.0 PAM3 designs.
-
product
PCIe 2.0 Protocol Analyzer
Summit T28
The Teledyne LeCroy Summit T28 PCI Express analyzer is for customers developing PCIe 1.0 or 2.0 x8 lane width server, workstation, desktop, graphics, storage, and network card applications.
-
product
4-CH 24-Bit 128kS/s Dynamic Signal Acquisition USB 2.0 Module
USB-2405
The USB-2405 is a 24-bit high-performance dynamic signal acquisition USB module equipped with 4 analog input channels providing simultaneous-sampling at up to 128 kS/s per channel. The USB-2405 also features software selectable AC or DC coupling input configuration and built-in high precision 2 mA excitation current to measure integrated electronic piezoelectric (IEPE) sensors such as accelerometers and microphones.
-
product
8 CANBus Channels, CAN 2.0 A/B Protocol or J1939 Protocol
CB3
The serial bus system with real-time capabilities is the subject of the ISO 11898 International Standard and covers the lowest two layers of the ISO/OSI Reference Model. Our CANBus modules provide independent, isolated channels of CAN serial data bus links, conforming to the ISO 11898 International Standard. All CAN nodes are able to transmit data and several CAN nodes can request the bus simultaneously.
-
product
ABex in System Programmer with Onboard SMH FlashRunner LAN 2.0 NXG
ABex AM-307 FR-NXG Flashrunner
The ABex AM-FR-NXG incorporates the FlashRunner LAN 2.0 Next Generation from SMH Technologies. The FlashRunner is used to program microcontrollers, flash and other logic and memory devices. All DIO’s, the programmable voltage lines and the corresponding ground lines can be switched by relays.The ABex AM-FR-NXG is equipped with an onboard Ethernet Controller which connects the FlashRunner directly to the PXIe Backplane of the ABex Chassis. Using a windows host, each AM-FR-NXG will provide its own network adapter.
-
product
PXIe USB 2.0 Hub With Programmable Connect & Disconnect
42-738A-001
The 42-738A-001 is a single-slot 3U PXIe USB Hub module that combines an 8-port USB 2.0 hub and USB data/power switching to provide a controlled connection between the backplane and USB products. Each port can connect and disconnect the power and data paths separately, simulating various connection faults.
-
product
Embedded Protocol Decode/Trigger Software for USB 2.0, 10/100 ETH, PCIe 2/1 for Infiniium Oscilloscopes
D9010EMBP
D9010EMBP includes the following powerful protocol decode and trigger software: PCI Express Gen 1 and Gen 2, USB 1.1, USB 2.0, eUSB2, USB HSIC, USB-PD, 10BASE-T Ethernet, and 100BASE-TX Ethernet.
-
product
USB4, USB 3.x, USB 2.0 and eUSB2 Protocol Decode/Trigger Software for Infiniium Oscilloscopes
D9010USBP
This application includes a suite of configurable protocol-level searches and software-based triggering specific to all USB standards. It is compatible with EXR-Series, MXR-Series, UXR-Series, S-Series, V-Series, and Z-Series Infiniium oscilloscopes. USB4 and USB 3.2 trigger and decode are not available for the EXR-Series, MXR-Series or S-Series oscilloscopes.USB4 and USB 3.2 trigger and decode are not available for the S-Series oscilloscopes. For detailed information on the decode and trigger settings, please refer to the datasheet. For assistance with using the applications, refer to the Infiniium help guide.
-
product
USB 2.0 Adapter
ADP-USB-445
The ADP-USB-445 USB 2.0 adapter converts one of the USB 2.0 headers on-board the WINSYSTEMS SBC35-427 single board computer to two type-A connectors on the front I/O panel. The integrated circuitry ensures noise immunity from the type-A connections to the single board computer and provides a robust power solution for external devices.
-
product
2.0 ~ 68.0 Gb/s Pulse Pattern Generator
CA9809
The UC INSTRUEMNTS CA9809 2.0 ~ 68.0 Gb/s Pulse Pattern Generator pulse pattern generator and error detector is a high performance, flexible and costeffective broad band data rate covered Pulse Pattern Generator that can operate from 2.0 Gb/s to 68 Gb/s. The CA9809 can be used with existing equipment to generate higher rate bit streams for use in telecom applications up to 68 Gb/s. Broadband test systems will benefit from the low power dissipation, precision connectors, and excellent output waveform characteristics. The compact size of the equipment allows the CA9809 to be placed at the measurement plane, reducing or eliminating artifacts related to long cables.
-
product
I2C Fast Mode Interface for USB 2.0, I2C Multimaster and Monitor
Connii MM 2.0
telos EDV Systementwicklung GmbH
Connii MM 2.0 is a small, compact, easy-to-use solution for a PC driven I2C transmitter and receiver. The I2C interface works as an I2C multimaster device. Thus, it is able to drive buses running multiple I2C bus masters. Additionally, Connii MM 2.0 is a limited I2C monitor for traffic up to 400kHz.
-
product
USB 2.0 Protocol Analyzer
LE-650H2
LE-650H2 is the hardware-based USB analyzer, which can record a large amount of data on the HDD/SSD of the PC, display translation with each class decode, and measure VBUS power consumption. The analyzer automatically detects the High/Full/Low speed of USB2.0/1.1 and starts measuring by simply pressing the space bar of the PC. The low cost device of easy operation by connecting it to the USB port of the PC is useful for developing/debugging the firmware/driver and study purpose of USB standard.
-
product
USB 2.0 SmartCable For MIL-STD-1553 Test And Simulation
ASC1553
The ASC1553 (AIM SmartCable) USB module offers full function test, simulation, monitoring and recording for MIL-STD-1553B applications implemented in an ultra compact form factor.
-
product
USB 2.0 SmartCable™ For ARINC429Test And Simulation
ASC429-x
USB 2.0 SmartCable™ for ARINC429 Test and Simulation with 6 channels (2Tx/4Rx) and 12 channels (4Tx/8Rx).
-
product
Dual 2.0 Gsps. 12 Bit ADC FMC
ADF-D2000
This FPGA Mezzanine Card (FMC) converts two channels of up to 2.8GHz analog input bandwidth at 1.0, 1.6, 1.8, or 2.0 Gsps and 12-bit resolution. Additionally, this FMC can be used in an interleaved mode to convert a single channel at 2.0, 3.2, 3.6, or 4.0 Gsps and 12-bit resolution. Based on the VITA 57 specification, the ADF-D1600 enables direct coupling of unparalleled analog-digital conversion capability with the VME/VXS/AMC/VPX/PCI-E carrier board of your choice. DEG engineers have designed this product and associated HDL firmware to work with both Altera and AMD FPGAs.
-
product
USB 2.0 Protocol Analyzer
LE-650H2-A
LE-650H2-A is the hardware-based USB protocol analyzer, which can record a large amount of data on the HDD/SSD of the PC, display translation with each class decode, and measure VBUS power consumption. The analyzer automatically detects the High/Full/Low speed of USB2.0/1.1 and starts measuring by simply pressing the space bar of the PC. The low cost device of easy operation by connecting it to the USB port of the PC is useful for developing/debugging the firmware/driver and study purpose of USB standard.
-
product
3.5" Embedded SBC With AMD LX800, Dual LANs, 4 COM, 4 USB 2.0 And VGA/LVDS/TTL
SBC84622
The SBC84622 supports an onboard low power AMD LX800 500 MHz processor with the AMD Geode CS5536 chipset. The flexible display function is supported by integrated graphics controller which allows users to configure both CRT and LVDS LCD or CRT and TTL LCD as simultaneous mode. Onboard one DDR SODIMM supports up to 1GB of system memory. Having such compact design with fanless operation, the SBC84622 can be applied in widely embedded and automation applications such as industrial automation, automation control, telecommunication, and process control.
-
product
USB-C® – USB 2.0 C Receptacle to A Plug
AUT17032-CRAP
This fixture is designed for USB-C 2.0 Plug and USB-A products.
