- Pickering Interfaces Inc.
product
PXI 24 Channel High Voltage Multiplexer
40-320-101
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
product
Harness Testers/Thickness Gauge
Our Hardness Testers/Thickness Gauges includes premium models such as the EMHT40, UTEMHT20 and UTEGEMTT2. These testers are precision instruments designed to measure the thickness or hardness of most metals. Two cost effective units - FHT801 and FHT803 are tailored to agricultural applications such as checking the ripeness of fruits and vegetables in fields/warehouses.
-
product
Harness Studio
Harness Studio is a browser for cable harness data, that brings together electrical and mechanical CAD-data into one program. It allows to navigate through very large cable harness data sets. Main aim of Harness Studio is being a tool that is very easy to use and allowing very flexible extraction of sub data sets.
-
product
Wire Harness Tester
Panther4HT Master- Slave DSU
Qmax Test Technologies Pvt. Ltd.
The Master- Slave DSU based Panther4HT Wire Harness tester is designed for testing and verifying electrical connections in a cable, harness, backplane or any other wired assembly. It offers unique Qmax MASTER - Slave concept and SATELLITE UNIT Options to avoid looping back of cable to the ATE. All Satellite Units communicates the measurements through LAN interface which is very useful for on-board applications in Aircrafts / Ships and similar applications where large cable looms are used. This i...show more -
product
5 ft Harness, 78-Pin Male Connector
GT96110
5 ft harness, 78-pin male connector on both ends
-
product
Harness Design and Manufacture
When designing an underwater cable harness, there are some factors which need to be considered, and we have produced the following list as a guide for customer information:Component considerations:- Electrical requirements- Mechanical considerations- Quality requirements- Reliability- Design redundancy (contact count)- Connector selection (type and form)- Locking requirements- Backpotting requirements- Waterblocking in moldings- Cable specification- Cable jacket material and compatibility with e...show more -
product
Automatic High Voltage Wire Harness Testers
Automatic high voltage wire harness testers are used in a variety of industries, such as aerospace and defence through to rail, and are used to test any equipment which contains a high number of electrical wires, or active components ensuring these pass specified test criteria at the sub-assembly and final stages of construction. These systems ensure the wiring and components are 100% compliant and undamaged, recording every test measurement and aiding diagnosis of detected faults.
-
product
Wire Harness Tester
NX Solo
The Dynalab NX Solo Wire HarnessTester is a low-cost, feature-packed, stand-alone tester with a maximum capacity of 256 test points. The flexibility of the NX System allows each program to perform multiple tests, display custom messages or sounds, and analyze the results of a test or an input to decide which operation to perform next. Testing for continuity, shorts, and a variety of components.
-
product
1' Harness, 50-Pin Male D-Sub Connector
GT97108
1' harness, 50-pin male D-sub connector on both ends.
-
product
Communication Protocol Test Harness
Simulate Master or Outstation Devices.Monitor Communications.Create Custom Functional Tests with any .NET programming language, Python, or Tcl/Tk scripts.Exercise a device as it will be used on the utility SCADA network.Automatically Perform Conformance Test Procedures.
-
product
Light-Guided Connector Assembly | Cable & Harness Tester
CableEye Light Director System
Our Light Director™ system (patented) provides a computer-guided technique for assembling connectors used in aerospace, medical, and other high-reliability applications. This system uses light fibers driven by super-bright LED lamps to individually illuminate target cavities in the connector being assembled. When the technician enters the wire code printed on unconnected wires, or touches a wire connected at the other end, the CableEye software turns on the appropriate fiber, thereby causing a b...show more -
product
2100Vdc Screw Terminal Connector Board | Cable & Harness Tester
CB29H
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with four 16-pole screw terminal blocks, the board addresses high voltage (HiPot) testing to 2100Vdc/1200Vac. Of particular interest to the harness testing market, the CB29H is also available as a transition board variant (CB29AH). The CB29H and CB29AH boards are high voltage versions of the CB29 with the high voltage traces running on inner layers to afford additional safety, and protection from contamination.
-
product
Electrical Circuit / Wire Harness Analyzer
ECAD System 2005
The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.
-
product
Wire/Cable Harness Tester
PANTHER 4HT
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
product
RF Coaxial Interconnect System VPX Compatible Rectangular Harness Solutions
VITA 67 Rectangular Harness
VITA 67 is a VPX standard for blindmate coax connectors that allows high density, high performance RF connections to be made between a backplane and plug-in modules.
-
product
USB Type-C Test Fixture | CB26U | Cable Harness Tester
A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test.
-
product
Cable and Harness Tester
CHT
The Cable and Harness Tester (CHT) provides multiple testing capabilities for up to 300 connector/harness test points. Test capabilities include DC Insulation Resistance (IR), DC and AC Dielectric Withstanding Voltage (DWV), and 2-Wire and 4-Wire Continuity.
-
-
product
Connector Board for Cable and Harness Tester
CB49
Populated with solder pads to accept a suite of TE-Connectivity Micro-MaTch connectors, this board addresses markets plagued by vibration and fretting corrosion, and requiring "miniaturized connectivity". Rated to 500Vdc/350Vac, the CB49 may be used on all CableEye models. The CB49, sold without connectors, contains nine sets of 20 solder pads accommodating numerous configurations of Micro-MaTch connectors.
-
product
Cable Harness EM Solver
MHARNESS
Electro Magnetic Applications, Inc.
MHARNESS to Complete the Last Mile of EM Coupling Simulation Traditionally, electromagnetic effects simulation has focused on the transients induced on the overall cable bundle of complex systems. MHARNESS is a transmission line solver that reveals the EM transients on the most critical element of systems: the pin interface to electronics systems. Now, EMA3D and MHARNESS can co-simulate in one self-consistent simulation.
-
product
3'Harness, 50-Pin Male D-sub Connector on one end, loose wired (numbered) other end
GT97107
3' harness, 50-pin male D-sub connector on one end, loose wired (numbered) other end.
-
product
CableEye Tester Calibration Verification Board | Cable & Harness Tester
CB50
Populated with precision resistors, it allows users to determine empirically whether the tester requires calibration. The CB50 may be used on all CableEye models. The CB50 is intended for periodic verification of tester calibration. To ensure that resistance measurements remain accurate, CAMI recommends yearly calibration. However, depending on environmental conditions and usage, testers may need calibrating more or less frequently.
-
product
Wire/Cable Harness Analyser
Qmax Test Technologies Pvt. Ltd.
Wire/Cable Harness Analyser by QMax
-
product
Hipot Wire Harness Testers
NX Hipot
* 50 to 1500VDC Hipot Testing* 50 to 1000VAC (optional) * 5Mohm to 1Gohm Insulation Resistance * Simple 4-button user interface * Tests for continuity and shorts * Tests a variety of components * Precision resistance measurements * Continuous high speed scanning for real time complete status information of harness assembly progress * Keyed security access and control * Built for rough industrial environments * 2 serial ports for connection to printers and scanners * Standalone operation * Uses a high capacity memory card * Available from 64 to 1024 test points * Networkable
-
product
Wire Harness Tester
NX Pro
The Dynalab NX Pro Wire Harness Tester is a low-cost, feature-packed, stand-alone continuity tester with a maximum capability of 512 test points. The flexibility of the NX System allows each program to perform multiple tests, display custom messages or sounds, and analyze the results of a test or an input to "decide" which operation to perform next. The NX Pro Tester has 1.3Mb memory capacity for program storage and is compatible with Printers, Scanners, and all other Dynalab NX System accessories.
-
product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty cri...show more -
product
4/5 Pin Trailer Harness Checker / Towing Maintenance Kit
#8026
Innovative Products of America
Test, clean and restore 4/5 pin trailer connections. Tester will verify tow vehicle is sending proper signal to the connector, while cleaning tool removes corrosion and verifies proper pin size on both male and female truck/trailer plugs. For use with 4/5 flat connectors. Patented. Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardsKit Includes: #7866: 4/5 Pin Trailer Harness Checker, #8021: 4/5 Pin Cleaner, and #8030: 2 ml DeoxIT Cleaner
-
product
3 Ft Harness, 78-Pin Male Connector On One End, Loose Wired (Numbered) Other End
GT97102
3' harness, 78-pin male D-sub connector on one end, loose wired (numbered) other end.
-
product
High Voltage, Continuity & Hipot, Cable & Wire Harness Test Systems
CableEye HVX, HVX-21
Fast ● Simple ● Preciseshow more
Advanced wiring analyzer scans for continuity (opens, shorts), miswires, resistance, capacitance, components (resistors, diodes, LEDs, capacitors) dielectric breakdown, insulation resistance, intermittent connections
HVX (Item 829) 1500 Vdc, 1000 Vac
HVX-21 (Item 829A) 2100 Vdc, 1200 Vac
For diagnostic and Pass/Fail Testing — Permits expanded testing (compared to models in our low voltage product line) for insulation resistance (IRI) and dielectric breakdown (DWV).
Al...- USB certified, PC-based tester for a versatile, fast, robust system with long life-cycle.
- Multilingual, dynamic, graphic-rich display (netlist & wiring schematic) provides clarity and speeds diagnostics.
- 128 Test Points, expandable to 1024 providing flexibility as your product line changes.
- User-selectable voltage to each connection group in the cable simplifies an otherwise complex process, accelerating testing.
- Programmable Ramp Up, Ramp Down, Dwell Time (same as Test Time), Trip Current, and Trip Delay (same as Soak Time) adds versatility.
- Current leakage detected during HV test phase provides a measure of insulation resistance up to 1 GΩ (HVX) and 5 GΩ (HVX-21) - any leakage current exceeding a preset limit reveals the presence of moisture, flux, or other contamination on exposed contacts.
- Real-time screening for intermittent connections for pinpointing elusive faults and improving quality.
- Automation scripting in a simple, intuitive language allowing non-programmers to reduce operator error by automating repetitive steps.
- Pop-Up Work Instructions. choose the exact amount of detail, imagery, language and automation you need to ensure your work instructions and tests are carried out flawlessly.
- Flexible tolerancing: optionally define as percentages or absolute terms, as well as asymmetrically (e.g. +0%/-10%) for improved yields.
- Barcode-tracking & archival data-logging to achieve error-proof test process and improved traceability & productivity.
- Print PASS/FAIL labels, test reports (with or without color wiring schematics/netlists) and log reports to satisfy ISO9000 reporting requirements.
- Compatible with laptop and touchscreen PCs for fieldwork and rack/off-bench mounting.
Includes:
CB29 board set (Item 759) for bare wire connections; comprehensive PC software with Database of >200 standard cables; 2 yr Product Support Subscription comprising Warranty, free tech support, and free software upgrades.
Select Add-On Options:
Hardware: 128-point Expansion Modules (attach to base); 4-Wire Kelvin Resistance Measurement, 1 mΩ at 1 A; Advanced Measurements; External Measurement Instrument Port (e.g. 10 GΩ Isolation at 100 V); Remote Control Connector for Deadman Switch; Environmental Sensor
Software: PinMap™ fixture editor, Connector Designer™ connector editor, or Autobuild™ guided assembly modules
camiresearch.com |@CAMI_CableEye |+1.978.266.2655 -
product
Cable Harness Test System
Data Patterns has built high reliability Cable Harness Test Systems for large installations. These are primarily used in launch vehicle aircraft and missile level cable harness test validation. Installations with upto 20,000 lines test capability at a single location have been supplied by Data Patterns. Portable version capable handling of as small as 384 points have also been addressed.
-
product
Training/Verification/Demonstration Fixture | CableEye Cable Harness Tester
Item 802 (CB-T2)
This multi-purpose CBT2 fixture can be used for operator training, tester system verification, and facility verification.
