Filter Results By:
Products
Applications
Manufacturers
SD Card
A non-volatile memory card format.
-
product
16-Bit Multi-Function With A/D, D/A And Digital I/O Channels CPCI Cards
GX3232 Series
The GX3232 is a multi-channel 16-bit, analog input and output cPCI module, supporting 32 single-ended or 16 differential input channels and four analog output channels. The inputs can be software configured for differential or single-end operation and are sequentially scanned with a maximum aggregate scan rate of 300 kS/s. Three input ranges are software-selectable: ±10 V, ±5 V or ±2.5 V. Optionally, the GX3232 is available with a high voltage input configuration and supports three ranges: ±60 V, ±30 V and ±15 V. The high voltage configuration supports 16 single-ended or 8 differential input channels for high voltage and 16 single-ended or 8 differential inputs for low voltage measurement. Four analog output channels provide software-selectable output ranges of ±2.5 V, ±5 V or ±10 V. The outputs can be updated either synchronously or asynchronously and support waveform generation. Each output can be clocked at rates up to 300 kS/s. A 16-bit digital I/O port is also provided, which supports 16 bidirectional data lines. Note that when used with a TS-700 system only 8 of these digital I/O lines are available at the test system's receiver interface.
-
product
3 Port RS-232/RS-422/RS-485 Interface CPCI Cards
GX3903 Series
The GX3903 is a 3-port, cPCI asynchronous communications interface board supporting RS-232, RS-422, and RS-485 interfaces. Each port is configured at the time of order for RS-232, RS-422 or RS-485 signaling. The default configuration is RS-232. For RS-232 mode, each port supports RTS, CTS, TXD, RXD, DCD, DRC, DSR, and RI signaling. The RS-422 mode supports TXD, RXD, CTS, and RTS with each line operating differentially with a uni-directional drive.
-
product
ARINC 429 Interface CPCI Card
RAR-429 Series
The RAR-429 module is a rugged, reliable, full featured, CompactPCI module designed to provide a stand-alone, ARINC 429 interface for avionics applications. Up to 16 ARINC429 channels are supported on a 3U CompactPCI module. The RAR-429 offers full functional test, simulation, and monitoring for ARINC 429 test and simulation applications.
-
product
16-Bit Multi-Function CPCI Card With A/D, D/A And Digital I/O Channels
GX3216 Series
The GX3216 is a multi-channel analog input and output cPCI module, supporting 16 differential input channels and two analog output channels. Dedicated 1 MS/s D to As and A to Ds allow simultaneous acquisition and generation of analog signals. Input ranges are software-selectable as ±10 V, ±5 V or ±2.5 V. The inputs are divided into two channel groups, with an independent software-controlled range assignable to each group. Two analog output channels provide software-selected output ranges of ±2.5 V, ±5 V or ±10 V and independent of the input range assignments. Output data is provided via two dedicated control registers, or through a 256 K-Sample FIFO buffer for waveform generation. Six bidirectional digital I/O lines are also available and can be programmed as inputs or outputs.
-
product
1553 Avionics Interface 3U CPCI Card
QCP-1553 Series
The QCP-1553 module is a rugged, reliable, full featured, Compact PCI module designed to provide a stand-alone, MIL-STD-1553A/B interface for avionics applications. Up to four independent dual redundant MIL-STD-1553 databus streams are supported by the 3U QCP-1553 module. Additionally, the module offers full functional test, simulation, monitoring and databus analyzer functions for MILSTD-1553A/B applications. An onboard IRIG-B time code decoder and generator allows users to accurately synchronize single or multiple QCP-1553 modules to a common time source. The QCP-1553 module is available in dual or full function (RT simulation, monitoring, and bus controller) configurations.
-
product
4 Port RS-232 & 4 Port RS-422 Interface cPCI Card
GX3904
The GX3904 is an 8-port, cPCI asynchronous communications interface board supporting (4) RS232 and (4) RS422 signal levels. The four RS232 ports offer a full set of data and modem control lines configured for DTE operation. The four RS422 ports offer differential signaling and support DTE operation. Each RS422 differential pair is terminated by a 150 parallel resistor. An optional transition cable is available to convert the front panel SCSI connector to (8) DB-9, D-sub connectors.
-
product
48 Channel Threshold Comparator FPGA PXI Card
GX3748
The GX3748 is a user configurable, FPGA-based, 3U PXI card which features 48 voltage comparator channels. The daughter board interfaces to the GX3700 FPGA baseboard which employs the Altera Stratix III FPGA. Each input channel can accept input voltage signals from 0 to 50 volts, with programmable threshold levels. Three of the 48 channels are supported by the board's timestamp event feature.
-
product
Standards Reference for Test Systems PXI Card
GX1034
The GX1034 offers PXI system designers the capability to develop a system re-certification strategy that employs only internal system resources. By incorporating the GX1034 as part of a system configuration, it is possible to develop a system accuracy verification strategy that can recertify a system's source and measure baseband instrumentation resulting in simplified support / maintenance logistics and improved system availability.
-
product
Ethernet Network Interface Cards
Our Ethernet cards, which support copper and fiber, are designed to relieve your bandwidth bottlenecks in compactPCI and VMEbus applications.
-
product
Network Interface Card
PMC-GBIT-DT2BP
The Ethernet network interface complies with the IEEE 802.3 specifications for 10BaseT, 100BaseTX, and 1000BaseT over category 5 twisted-pair cable. Full-duplex and half duplex modes are supported. The PMC-GBIT-DT2BP is compliant with standard singlewide PMC IEEE P1386.1, PCI 2.2, and PCI-X 1.0 specifications.
-
product
Network Interface Card
NIC10G
Featuring the Intel 82599ES dual 10GbE controller, the NIC10G supports flow control, integrated IPsec security engines, optimized queues, IPv6 offloading, advanced filtering capabilities, and Tx/Rx IP, TCP and UDP checksum offloading capability. Also has integrated a PCI Express Gen 2 interface supporting up to 8 lanes.
-
product
Network Interface Card
XMC477RC
The XMC477RC is a quad switched mezzanine card (XMC) compatible module providing a 4-channel Gigabit Ethernet Small Form Factor pluggable (SFP) interface.
-
product
Network Interface Card
NIC10GBT
The NIC10GBT is a dual port 10GBase-T XMC module that brings 10GbE expandability to new and existing embedded systems with available XMC slots.
-
product
Network Interface Card
NIC10GFT
The NIC10GFT is a dual port 10GBase-T XMC module that brings 10GbE expandability to new and existing embedded systems with available XMC slots.
-
product
PCI Express Graphics Cards
ADLINK’s PCI Express Graphics Cards - based on NVIDIA's embedded GPUs - can boost the performance of a wide range of workloads, including image processing and analysis, computing acceleration, and artificial intelligence (AI). ADLINK’s PCI Express Graphics Cards offer high performance, high data bandwidth, power efficiency, and longevity support in a reduced hardware footprint. ADLINK’s PCI Express Graphics Cards connect via a common interface and are easy to integrate and use to increase system responsiveness and accuracy, as well as decrease latency for industrial automation, healthcare, transportation, aerospace and defense, gaming, and telecom applications.
-
product
PCI GPIB (IEEE-488) Interface Card - PCI-GPIB
PCI-GPIB
PCI IEEE-488 interface card (PCI Card for Windows OS)
-
product
(Bundle Sale) PCI Express Graphic Card with NVIDIA® Quadro® P4000
Quadro-E PEG P4000
The Quadro-E PEG P4000 perfectly balances performance, features, and compact form factor to deliver exceptional creative experience and productivity across a variety of 3D applications. The Pascal GPU with 1792 CUDA cores, 8GB GDDR5 onboard memory and support for up to four 8K (7680×4320 @ 60 Hz) native displays accelerate product development and creation workflow demanding fluid interactivity for large, complex 3D workpieces.
-
product
(Bundle Sale) PCI Express Graphic Card with NVIDIA® Quadro® P2200
Quadro-E PEG P2200
The Quadro-E PEG P2200 perfectly balances performance, features, and compact form factor to deliver exceptional creative experience and productivity across a variety of 3D applications. The Pascal GPU with 1280 CUDA cores, 5GB GDDR5 onboard memory and support for up to four 5K (5120x2880 @ 60Hz) native displays accelerate product development and creation workflow demanding fluid interactivity for large, complex 3D workpieces.
-
product
Power Switch Card
1260-120
Each channel of the 1260-120 can switch up to 13A, 250VAC or 10A, 125VDC; its switching capability makes it the ideal solution for applications requiring high-current switching of AC power, DC power supplies, and AC or DC current sources.
-
product
High Density DPDT Plug-In Switch Card
1260-112
The Astronics 1260-112 is a 96-channel, high-density, double-pole, double-throw (DPDT), switch for the Adapt-a-SwitchTM platform.
-
product
80/24 Channel SPST Plug-in Switch Card
1260-118/118A
The Astronics 1260-118/118A is an 80/24-channel, SPST (Form A) plug-in relay card for the Adapt-a-Switch™ platform.
-
product
High Density, 64-Channel Switch Card - 64 Channel, SPDT, High Isolation, Low Crosstalk Switch Module
1260-16A
The Astronics 1260-16A is a 64-channel, SPDT, high isolation; low crosstalk switch module designed for switching and routing sources such as AC and DC power supplies in automated test systems. The 1260-16A switches currents up to 6A, AC or DC, and voltages up to 110VDC or 250VAC.
-
product
Modular VXI Switch Card Carrier
1260-100
The 1260-100 Switch Carrier accommodates up to six plug-in switch cards, providing optimum switching solutions while reducing the ATE size requirements.
-
product
Digital I/O Switch Card - 96 Open Collector Channels in 12 Groups of 8 Bits Each
1260-14/14C
The Astronics 1260-14 Digital I/O Switch Card provides 96 open collector channels in 12 groups of eight bits each. With the open collector version each independent group can utilize a separate internal or external pull-up supply up to 32VDC.Each channel can be configured as an input or an output and individually controlled in the asynchronous mode, or be synchronous with other channels.
-
product
Modular VXI Switch Card Carrier
1260-101
The 1260-101 Switch Carrier accommodates two plug-in switch cards in a single slot VXI module.
-
product
52/20 Channel SPDT Plug-In Switch Card
1260-117/A
The Astronics 1260-117/A is a 52/20-channel, SPDT (Form C) plug-in switch card for the Adapt-a-Switch™ platform.
-
product
Microwave SPDT Plug-In Switch Card
1260-160B/E
The Astronics 1260-160B/E is a 1 or 2-slot microwave switch plug-in for use in either the Astronics 1260-100 Adapt-a-Switch™ VXI carrier or the 1256, GPIB/RS-232 Switching Mainframe.
-
product
Coaxial Plug-in Switch Card
1260-152/172
The Astronics 1260-152/172 is a high- frequency coaxial switch card for use in either the Adapt-a-Switch® 1260-100, VXI carrier, or the 1256, GPIB/RS-232 Switching Mainframe.
-
product
High Density SPDT Plug-In Switch Card
1260-116
The Astronics 1260-116 is a 24-channel, Form C, single-pole double-throw (SPDT) switch card for use in either the 1260-100 VXI Carrier or the 1256 GPIB/RS-232 Switching Mainframe.
-
product
Matrix Switch Cards
1260-145
These quickly and easily plug into the front of Astronics 1260-100 and 1260-101 Adapt-a-Switch™ carriers or Astronics 1256 GPIB/Ethernet and 1256L (LXI Core 2011 Compliant) switching mainframes.
