Filter Results By:
Products
Applications
Manufacturers
RJ45
Common name for any 8P8C modular connector.
-
product
Cble Assmbly Ins Push-On F To RJ45 Plug
#TCA001
Cable Assembly, Insulated Push-on F to RJ45 Plug, 849160004783
-
product
Coupling Decoupling Network for Communication Lines
CDN61000-5C
• Application Range: ≤4kV, 1.2/50us pulse, 8 wire unshielded twisted pair (UTP) • Test Voltage: Max 4KV, 2 kV (1.2/50 µs pulse when RJ45 connector is connected. Maximum test voltage is 1.5kV when RJ45 female is unconnected or auxiliary terminal is not protected.) • Coupling mode: 90V gas- discharge tube+250ohm Resistor/Each Wire, 8 Wires Simultaneously-Ground (Common Mode) • Input and output interface: RJ45 connector • Terminal layout (RJ45 connector): First pair of lines: pins 1/2 Second pair of lines: pins3/6 Third pair of lines: pins 4/5 Fourth pair of lines: pins 7/8 • Max. operating speed: 1000MBit/s • Max operating voltage: Max 50V DC • Max operating current: Max 1A Related Instruments
-
product
Day/Night IP Surveillance Camera
ENVIROMUX-IPCAM-N
View and control the camera from the ENVIROMUX web interface, the camera web interface, included software, or with a compatible cell phone. With the ENVIROMUX-2D/5D/16D, a triggered snapshot can be forwarded in alert e-mails. A snapshot can be triggered by any programmed event (motion detection, door open/close, glass break, smoke, liquid detection, etc.). Image sensor: 1/4" progressive scan CMOS sensor. Video Streaming: simultaneous Motion JPEG and MPEG-4. Frame rate: 30fps at 640x480 (VGA) resolution. Lens: F2.0, 4.3 mm (0.17 in), 12 infrared LEDs for night vision. RJ45 connector. Wireless models: wireless IEEE 802.11 b/g up to 54 Mbps. Regulatory approvals: CE, FCC, RoHS.
-
product
Erbium Doped Fiber Amplifier
EDFA
Sichuan Jiuzhou Electronic Technology Co.,Ltd
*Imported SDL or Lasertron 980nm / 1480nm Pump Laser.* Imported Lucent or Fibercore Erbium Doped Fiber.* Double Pump Lasers design ensures high power.* Wide range switch power supply.*Supports remote control with JIUZHOU HFC Net-managing Software via RJ45.
-
product
Ethernet to Relay Interface Boards
Model 8064 OEM
* 115631-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully VXI-11 compliant.* Easy configuration with any web browser.* Includes 50-pin mating connector for solder connections.* Optional terminal board for easy connections without soldering. See the Ethernet Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS Wiring Kit to connect to an RJ45 connector on the rear panel.
-
product
FPGA Mezzanine Card
FMC432
Sundance Multiprocessor Technology Ltd.
The FMC432 is a dual 10 Gigabit Ethernet (10GBASE-T) FPGA Mezzanine Card with two RJ45 connectors available on the front panel. Compliant with the VITA 57.1 standard the FMC432 is compatible with FPGA carrier cards offering High Pin Count connectors. It also allows for the option to stack an additional FMC over it. Any of the 4DSP FMC that use LVDS and single ended signaling only can be mounted over the FMC432, thus offering users with the ability to build a complete high speed data acquisition, waveform generation and communication solution while using a single FMC site on an FPGA carrier card.
-
product
Gigabit Ethernet
SFP Transceivers - Copper
Copper SFP transceiver modules (1000Base-T) are 100% compatible with Cisco equipment, include RJ-45 connector, and compliant with applicable industry standards.
-
product
Glass Break Detection Sensor
ENVIROMUX-GBS
Acoustically detects the cracking of glass. Adjustable sensitivity. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D.
-
product
Infrared Motion Sensor
ENVIROMUX-IMD
Registers movement in the area covered. Condition display via LED. Provides immunity from common-mode signals such as the effect of strong hot or cold air currents, variation in ambient temperature, background radiation and acoustic noise. 24 dual-element detection zones for long, mid and short range protections. Surface or corner mounting. Pulse count or single shot triggering. Good RFI protection. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Includes mounting bracket for installing the sensor to a ceiling or wall. Regulatory approvals: CE, RoHS.
-
product
IP Surveillance Camera
ENVIROMUX-IPCAM
View and control the camera from the ENVIROMUX web interface, the camera web interface, included software, or with a compatible cell phone. With the ENVIROMUX-2D/5D/16D, a triggered snapshot can be forwarded in alert e-mails. A snapshot can be triggered by any programmed event (motion detection, door open/close, glass break, smoke, liquid detection, etc.). Image sensor: 1/4" progressive scan CMOS sensor. Video Streaming: simultaneous Motion JPEG and MPEG-4. Frame rate: 30fps at 640x480 (VGA) resolution. Lens: F2.0, 4.0 mm (0.16 in). RJ45 connector. Wireless models: wireless IEEE 802.11 b/g up to 54 Mbps. Regulatory approvals: CE, FCC, RoHS.
-
product
Legacy Liquid Detection Rope Sensor
ENVIROMUX-LDSx-y
For warning of flooding. Detects liquid depth >0.1" (2.5 mm). Minimum puddle: 0.6" (15 mm) diameter. 100% waterproof electronics. Detects any liquid or moisture, except deionized water. RJ45 connector. Voltage Supply: 12VDC. Current Consumption: 20mA. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Available water sensor cable (x) lengths: 1/10/50/100/200/400/600/800/1000 feet. Plenum rating: CL2P (UL). Available 2-wire cable (y) lengths: 5/10/20/50/100 feet. Powered by ENVIROMUX-SEMS-16U and SERIMUX-S-x. Regulatory approvals: CE, RoHS. Requires the ENVIROMUX-SEMS-16U and SERIMUX-S-x to operate. Use self-adhesive clips (ENVIROMUX-CLP10-LD) to prevent sensor rope cable from shifing after installation. ENVIROMUX-CLP10-LD includes 10 clips.
-
product
LiFi HotSpot Evaluation Kit
The Li-Fi HotSpot Evaluation Kit allows the establishment of an optical wireless bidirectional point-to-point full-duplex data connection over medium distances in the meter range. Data rates of up to 1 GB/s are supported at a distance of up to 5 meters. The kit consists of two Li-Fi HotSpots, two CAT-6 cables (RJ45), two external power supplies and a user manual. Users can thus get to know the technical advantages of Li-Fi technology with little effort and test and evaluate them in their own network or environmental conditions.
-
product
Light Intensity Sensor
ENVIROMUX-LIS
Detects and measures the luminous intensity of light. Ideal for monitoring unmanned closets, telecom rooms, remote data rooms, or other low traffic facilities. Applications from 0 to 128,000 lux. Human eye response (540 nm peak sensitivity). IR and UV rejection. RJ45 connector. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS. Compatible with ENVIROMUX-2D/5D/16D.
-
product
M2T Transmitter
The M2T half-rack transmitter houses two stereo transmitters to provide two stereo audio channels, and for up to four mono audio channels in a single rack space. The audio inputs can be individually configured to be analog or Dante compatible. The analog input connectors are full-size XLR/TRS combo types for balanced line-level analog signals while the input preamp circuits use a special balanced amplifier with very high common mode rejection to minimize hum and noise. A Dante™ Ultimo™ interface via dual RJ45 connectors accepts Dante networked audio inputs and can daisy chain the digital stream to additional units via CAT6 cables. An additional RJ45 jack provides an Ethernet connection for programming and control via Wireless Designer™ software and a USB jack on the front panel allows for firmware updates. The transmitter features a full color, backlit LCD for high visibility in any environment, while the chassis is all-metal and can be racked singly or in pairs using included rack mount hardware.
-
product
Mini Lan Tester
21-8572-00
Auto decipher the straight and cross-over pinning?RJ45 each pair connected display.
-
product
Mini Media Converter
MX Series
The MX mini media converter provides one RJ45 10/100/1000Base-T connector supporting auto-negotiation, MDI/MDI-X, full-duplex and half-duplex. The other connector is a 1Gbps SFP slot, suitable for any 1Gbps SFP module.
-
product
Modules
Cimetrics offers several modules that can enable you to add BACnet capability to your products. Our modules, based on the Lantronix XPort, are elongated Ethernet RJ45 connectors that can be built into your product. Each module contains a microprocessor, memory, Ethernet MAC/PHY, serial (UART) interface, and firmware written by Cimetrics. The serial interface is typically used to communicate with another microprocessor in your product.
-
product
Multifunctional Cable Detectors
Shenzhen Noyafa Electronic CO.,LTD
NOYAFA Multifunctional Cable Detector has a very high cost-effective, it can quickly trace and identify UTP/STP RJ45/ RJ11/BNC/ metal cable.
-
product
Optical Platform
Sichuan Jiuzhou Electronic Technology Co.,Ltd
* Supports 12 functional modules.* Hot-plug & auto recognition.* LCD displays key parameters of functional modules.* Supports remote control with JIUZHOU HFC Net-Managing Software via RJ45.* Power supply module fixed inside of platform, does not occupy any space of functional modules
-
product
Optical Transmitter
Sichuan Jiuzhou Electronic Technology Co.,Ltd
* JDSU DFB laser* JDSU External Modulator.*2 optical outputs, 7/9/10/11dBm available.* SBS Threshold 13/16/18dBm adjustable.*Wide AGC range -10~+10dB.* ATC, APC functioned.* Redundant power supply: AC 85~265V and DC -36~-60V.* Supports remote control with JIUZHOU HFC Net-Managing Software via RJ45.
-
product
Outdoor Infrared Motion Sensor
ENVIROMUX-IMD-O
Outdoor weatherproof - high reliability against water and insects. Double conductive shielding to eliminate false alarms from light sources. Registers movement in the area covered: 40 ft (12 m) x 50 ft (15 m) - 120° wide. LED lights during detection. Selectable detection paterns: Multi-Level (40 zones) or Pet Alley (18 zones). Unwanted detection areas can be eliminated using the included area masking strips. Selectable Sensitivity: High, Mid and Low. Adjustable to the brightness of surrounding environment with the Day/Night Mode switch. Tamper switch opens when cover is removed. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: -4 to 122°F (-20 to 50°C). IP54 compliant. Powered by ENVIROMUX-2D/5D/16D.
-
product
Professional LAN Installation Tool kit
CTK400LAN
The StarTech.com Professional LAN Installation Tool kit provides all the necessary tools to install and test RJ45 networks in a compact, handy, carrying case.
-
product
Rear-Panel I/O Transition Module
CP3-GESW8-TM8
CP3-GESW8-TM8 is a rear-panel I/O transition module providing flexible access to CP3-GESW8 or NETernity™ CP3-GESW8N rear-panel I/O. Up to eight Gigabit Ethernet ports of the switch are accessible from the transition module's stacked RJ-45 connectors. Each Ethernet port is routed as four 100 Ohm differential pairs.
-
product
RF Down-Converter
CDC100A
Systems Engineering & Management
The CDC100A Series Down-Converter is a 1U rack-mount device designed for use with antennas that have a Tri-Band Feed. The CDCMA100 Series Down-Converter is a synthesized down-converter supporting 1415-1585 MHz, 1650-1850 MHz, 2185-2485 MHz and 4400-5250 MHz, down-converting 4400-5250 MHz to 1415-2485 MHz. The CDC100A is provided as a 1U Expansion Chassis that communicates with any SEMCO receiver via an RS-485 protocol. The communications I/O is via RJ45 and the operator interface is via the receiver RCMS GUI.
-
product
RJ45 Connectors
*Multiple Platforms Available, 1×1, 1xN, 2xN, Vertical Mount, Offset, Low profile*CAT3 to CAT5e Connectors Available*With & Without LEDs*With & Without Shields*Extended Temperature -40°C to +85°C*THT, Pin-In-Paste & SMT Options
-
product
RJ45 (Ethernet 100 Base T) to 90 Series Interface
J90RJ45I
RJ45 Ethernet connector for VPC Tripaddle ITA module Up to 3 connectors per module For Cat 5 Fast Ethernet cable IEEE 802.3 standard 100 Base-T
-
product
RJ45 (Ethernet 100 Base T) to 90 Series Interface (R)
J90RJ45R
RJ45 Ethernet connector for VPC Tripaddle 90 series RCV module Up to three connectors per module For Cat 5 Fast Ethernet cable IEEE 802.3 standard 100 Base-T
-
product
Shield
Arduino Ethernet Shield 2
The Arduino Ethernet Shield 2 connects your Arduino to the internet in mere minutes. Just plug this module onto your Arduino Board, connect it to your network with an RJ45 cable (not included) and follow a few simple steps to start controlling your world through the internet. As always with Arduino, every element of the platform – hardware, software and documentation – is freely available and open-source. This means you can learn exactly how it's made and use its design as the starting point for your own circuits. Hundreds of thousands of Arduino Boards are already fueling people’s creativity all over the world, everyday. Join us now, Arduino is you! *Requires an Arduino Board (not included)
-
product
Smoke Detection Sensor - CE Approved
ENVIROMUX-SDS-CE
For warning of smoke. Photoelectric smoke detector. Smoke sensitivity: 0.08-0.14 dB/m. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: 14 to 122°F (-10 to 50°C). Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
product
Smoke Detection Sensor - UL Approved
ENVIROMUX-SDS
For warning of smoke. Photoelectric smoke detector. Smoke sensitivity: 0.98-2.4%/ft. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: 14 to 122°F (-10 to 50°C). Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL, RoHS.
