Filter Results By:
Products
Applications
Manufacturers
-
product
CC-TLP Probe
CC-TLP-50-A1
High Power Pulse Instruments GmbH
*Capacitively coupled TLP probearm (CC-TLP) compatible with standard probing stations*18 GHz SMA connector*Tilt angle adjustment*Calibration gauge for needle height
-
product
Complete Probe Station
BD Series
Best for DC and RF probing, the platen lift is designed for smooth raise and contact of your probes simultaneously to your device. It is ideal for probing multiple spots on your device, or through multiple devices.
-
product
Controlled Environment Probe Station
CG-196
Everbeing controlled environment probe station allows vacuum and cryogenic probing down to 77K with liquid nitrogen or high temperature probing up to 1273K. Efficient in characterizing your devices at extreme temperatures, vacuum, specific gas, etc.
-
-
product
DYNAMIC TRACKING
VXTRACK
The C-Track dual-camera sensor is a complete portable 3D measurement solution that offers probing inspection and dynamic measurement capabilities. It is fitted with high-quality optics and special lighting, enabling it to measure all reflectors within its operating space. The probing stylus is very useful for aligning parts with respect to a referential (calculated using a group of reflectors), which allows movement or deformation monitoring directly on the part's referential.
-
product
Fixture and Software for Open/Leak Inspection
In addition to jigs and fixtures for probing conductors and electrode pads, NIDEC-READ provides specialized software for test point selection and log analysis.
-
product
Flexible Probearm for HBM and Flex-Pitch Applications
TPA-GFG
High Power Pulse Instruments GmbH
*Electrically isolated probearm for GND needle contact or general purpose DC, twin-wire HBM or flexible pitch VF-TLP/TLP/HMM/HBM force/sense probing based on the HPPI GF-A flexible pitch setup.*Flexible rotation of the probearm by precision gear 80:1*Suitable to mount the GF-A ground fixture needle for flexible pitch measurements. In addition a cable (e.g. for HBM) can be directly connected to the contact pin.*High stability
-
product
Gold Probes
4900 Series
The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.
-
product
High Power Probe System Solutions
MPI Advanced Semiconductor Test
MPI high power probing solutions offer variety of probing systems which include manual, automated and fully-automated versions to provide solution for different budgets and specific requirements.
-
product
High Voltage Isolator for Logic Analyzers
LX-08
The LX-08 series of high voltage logic analyzer adapters provides a safe isolated method of measuring high voltage control signals with a low voltage logic analyzer. All inbound signals are optically isolated and attenuated to a safe level for the delicate inputs typically found on logic analyzers. The inputs on the LX-08 are capable of withstanding voltages up to +/- 300V AC/DC, higher voltage configurations are available upon request. Rather than probing with multiple neon screwdrivers, the LX-08 can provide simultaneous viewing of up to 8 circuits in the STANDALONE mode via the indicator array. Need to catch a transient event or map out a timing sequence? Just add a logic analyzer to the outputs of the LX-08 and turn it into a high voltage logic analyzer. High voltage signals that were hazardous for a logic analyzer can now be measured safely. Typical outputs of a high speed PLC sequencer can be precisely timed and measured from both sides of the control relay. With the built in user selectable AC filter circuit, an AC signal can be measured as DC events or AC cycles.
-
product
Inline Micropositioner
SP-150
Signatone's most stable and precise micropositioner for sub-micron probing.
-
product
Laser Scanning
Laser scanning is the non-contact alternative to tactile probing, which along with point cloud processing software, enables an entirely digital inspection process. From measurement preparation to final report, this approach is significantly faster, provides a more profound insight and lowers development costs.
-
product
Logic Analyzer Cable
The logic analyser cable plugs in to the AUX port of the SmartScope, providing 8 shielded probe pins for each of the digital inputs, as well as the external trigger input. Each digital probe has its own ground connector and embeds a small passive filter close to the header, allowing for digital probing without signal cross-talk on the cable
-
product
Logic Analyzers
Verification and debug of today's high speed, low voltage digital signals requires probing solutions that can accurately acquire from a wide variety of electronic designs and protect signal fidelity. Tektronix logic analyzer probes contain a variety of connectivity options that are engineered to ensure that signal acquisition is a true reflection of your design's performance. Compare and learn more about Tektronix logic analyzer probe solutions.
-
product
Manual Probearm for HBM and Flex-Pitch Applications
TPA-GFM
High Power Pulse Instruments GmbH
*Electrically isolated probearm for GND needle contact or general purpose DC, twin-wire HBM or flexible pitch VF-TLP/TLP/HMM/HBM force/sense probing based on the HPPI GF-A flexible pitch setup.*Suitable to mount the GF-A ground fixture needle for flexible pitch measurements. In addition a cable (e.g. for HBM) can be directly connected to the contact pin.*High stability
-
product
Mercury Four Point Probe
Based on decades of experience with needle four point probes and C-V, I-V Mercury probing stations, Four Dimensions developed a Mercury four point probe (patent pending). The liquid metal Mercury is used to form temporary electrical contacts at four terminals. These probes cause no damage to the sample and permit no contact pressure probing.
-
product
Mercury Probes
Materials Development Corporation
MERCURY PROBES are precision instruments that enable rapid, convenient, and non-destructive measurements of semiconductor samples by probing wafers with mercury to form contacts of well-defined area.
-
product
Metra Scan 3D
The most accurate scanning and probing solutions, whether in lab or on the shop floor.Highly accurate measurementDynamic referencingComplete metrology solution
-
product
Micropositioner
S-725
Primarily used for probing targets that are approximately 0.5 mil (12.7 microns) and larger, with 80 TPI resolution.
-
product
Micropositioner
XYZ 500 MIMT
Quarter Research and Development
Submicron manipulator and translation stage. The XYZ-500-MIMT Micropositioner is intended for precise probing and instrumentation for industrial, medical, biological, semiconductor, and general scientific applications. It provides 3-axis motion with .500" movement on each axis. Motion is controlled by three precision stepping motors attached to precision gear heads 64:1 (standard), that drive a 100 threads per inch screw (standard).
-
product
Micropositioner
MP-40
Engineered for highly demanding probing needs, the Korima Model MP-40 Micropositioner is precision-built for micropositioning to meet ever smaller industry standards. Featuring linear motion on all three axes, the MP-40 provides precise control for sub-micron probing.
-
product
Micropositioner
MP-80
Engineered for highly demanding probing needs, the Korima Model MP-80 Micropositioner is precision-built for micropositioning to meet ever smaller industry standards. Featuring linear motion on all three axes, the MP-80 provides precise control for sub-micron probing.
-
product
Microscopes
A digital or traditional optical microscope can help engineers check on their high-speed probing activities much more easily. It will assure the probe tips will touch on the right contact(s), with correct contact angle and right amount of force. We use both digital and optical microscopes in our own lab. The information in this page is to help you choose a microscope best suits you.
-
product
Microscopes
Probing Solutions offers Microscopes made by Azoom, Excelitas, Meiji, Leica, Mitutoyo, and Motic. To order Microscopes, please call PSI at (775) 246-0999, or email sales@probingsolutions.com for a quote.
-
product
Micro-Surface Microprobe
ICT-4
ICT-4 Micro-Surface Microprobe - For use on integrated circuits and other micro specimens. 0.013'' diameter .5'' straight stainless steel shaft; slightly protruding sensor bead to facilitate temperature probing. 5'' tubular handle fits micro-manipulators. Maximum intermittent temperature 200°C, continuouse use 100°C, Time constant 0.025 Seconds. 5 foot lead. Not isolated.
-
product
Mini Probe Station
C-2
The smallest probe station which still preserves the key functions and precision that are fundamental to all probing. This size is still capable of DC and RF measurements, making it the most versatile in its size.
-
product
Nano Technology Products
We are instrumental in offering quality range of nano technology products that find application in defense research and development organization. Our range encompasses probe station, microscope, extension cable, adopter and RF probing, and vibration isolation products. We have the ability and resources to design products in line with the exact specifications provided by the clients.
-
product
Passive Oscilloscope Probes
5900 SERIES
Probe Master's new 5900 series passive oscilloscope probes are available in 400 MHz & 500 MHz bandwidths. Probes are also available with readout actuators for oscilloscopes with the readout feature. The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.The probe body is made of high impact ABS. Soft molded strain reliefs at all stress points assure long cable life. In short it has been designed to offer you high performance coupled with high quality.
-
product
PCB Holders
PacketMicro offers a family of horizontal and vertical PCB holders for engineers to hold PCB in a desired orientation for steady and easy probing.
-
product
PORTABLE COORDINATE MEASURING MACHINE
CMM
The HandyPROBE arm-free probing system generates high-accuracy measurements (accuracy of up to 22 µm), and outperforms traditional portable CMMs on the shop floor. The HandyPROBE portable CMM is currently used on the production lines of major players from the automotive, aerospace and manufacturing industries.
