Filter Results By:
Products
Applications
Manufacturers
Passive Intermodulation
1.) Protocol Independent Multicast - network routing over existing unicast framework. 2.) Passive InterModulation - RF interference generation condition.
-
product
Passive Component Integration - PXIe
Passive Series
The Passive PXIe module is a highly customizable PXIe module that can integrate the passive components of your choice.We can customize the Passive module with a wide range of passive components: WDM couplers, splitters, circulators, band-pass filters, PM beamsplitters, MUX, DeMUX and more.Our spec sheet contains a selection of popular configurations.Please contact us to discuss your specific requirements at sales@quantifiphotonics.com.
-
product
Passive Component Integration
Integrate passive optical components of your choice such as WDM couplers, splitters, band-pass filters, PM beamsplitters and circulators. PXIe and benchtop models support SMF, MMF and PMF.
-
product
Passive Intermodulation Analyzers
The current standard of PIM testing offers a well-known system of two primary carriers and a calculated PIM frequency, which is monitored via a spectrum analyzer. This provides a measurement of the overall linearity of the antenna system and the surrounding environment.
-
product
Antenna, Omni-Directional Wideband Discone
EM-6105 | 10 KHz – 2 GHz
The EM-6105 is a broad band collinear array allowing very wide Omni-Directional frequency coverage in a single package. Below approximately 100 MHz, the EM-6105 acts as an active vertical rod which offers 10 to 12 dB more signal handling capability than competitive antennas (overload field strength: 2 V/meter) which greatly reduces intermodulation generated signals in a typical read world RF environment. In the congested spectrum above 100 MHz the antenna is passive and contributes no intermodulation products so the overload point is determined solely by the receiving instrument. This immunity to overload can often make the difference between useful signal output and an indecipherable jumble of spurious products and is accomplished without compromising sensitivity. The antenna collapses for convenient storage and transport. The EM-6105 is supplied with an EM-6106 Battery Pack.
-
product
Antenna, Wideband Discone
EM-6115 | 10 KHz – 2 GHz
The EM-6115 is a broad band collinear array allowing very wide Omni-Directional frequency coverage in a single package. Below approximately 100 MHz, the EM-6115 acts as an active vertical rod which offers 10 to 12 dB Greater unsaturated instantaneous dynamic range than competitive antennas (overload field strength: 2 V/meter) which greatly reduces intermodulation generated signals in a typical read world RF environment. In the congested spectrum above 100 MHz the antenna is passive and contributes no intermodulation products so the overload point is determined solely by the receiving instrument. This immunity to overload can often make the difference between useful signal output and an indecipherable jumble of spurious products and is accomplished without compromising sensitivity. The antenna collapses for convenient storage and transport.
-
product
Battery Portable Passive Intermodulation Analyzer
iPA Series
The iPA Series Passive Intermodulation (PIM) analyzer is the first battery powered PIM Test Analyzer versatile enough to support multiple test scenarios such as testing at the top of the tower, base of tower, roof top and in-building for DAS systems. This IEC compliant 20W, rugged, battery operated design includes a tablet computer in a ruggedized case for remote control. This allows hands-free dynamic testing that is safe and convenient. Add the optional Range to Fault (RTF) module to quickly identify the location of PIM and Return Loss sources.
-
product
Coaxial Switches
An electromechanical switch made primarily for routing microwave signals/RF energy from one point to another within a transmission line. Coaxial switches can be used in either an industrial environment or in the lab. These electromechanical devices are also used for RF testing equipment and in large RF communication systems and networks. Coaxial switches vary by port configuration, switch type, maximum frequency, isolation, insertion loss, voltage standing wave ratio (VSWR) and package type. Coaxial switches are able to route RF signals over a broad bandwidth from DC to 40 GHz, and are now offered with the Low PIM option which will improve Passive Intermodulation levels from -110dBc (standard switch) to -160dBc.
-
product
PIM Testing
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Passive Intermodulation (PIM) is a non-linear response of two or more signals of different frequencies mixing together in a passive device, e.g., antenna, cable, con- nector or splitter. Today, PIM has become a very serious, and challenging issue for mobile operators, equipment vendors, and component manufacturers due to frequency planning in modern communication networks, the usage of high-power transmitters and the usage of more sensitive receivers in base stations. If a PIM with sufficient magnitude generated from a transmitter falls within an adjacent receiver channel, it causes serious interfe- rences to the base station receiver and will significantly degrade the network quality of service.
-
product
Shielding Solutions
Antenna Test Chambers are especially designed for testing RF devices and antennas from frequency ranges of 700 MHz to 6000 MHz. These Antenna Test Chambers provide a shielding of more than 90 dB as well as lowest residual passive intermodulation.
-
product
PIM Chamber
Passive Intermodulation (PIM) occurs when two or more signals are present in a passive device (cable, connector, isolator, switch, etc.) that exhibits a nonlinear response.PIM chambers vary in size and design depending on the size of the DUT; a typical PIM requirement is -110dBc or more. Cuming Lehman Chambers has successfully provided PIM Chambers with measured levels in excess of 150dBc.
-
product
3-Channel LOW PIM Attenuator
Corry Micronics' 3 channel, LOW PIM attenuator covers the 400 to 3000 MHz frequency range and has been specifically designed for major mobile access carriers who are attempting to measure or monitor passive intermodulation distortion/interference in communications systems.
-
product
Bench PIM Tester - iBA series
iBA
Passive Intermodulation (PIM) occurs when multiple RF signals encounter defects in materials or workmanship in an RF path. These defects behave like a mixer causing noise to be generated at mathematical combinations of the original carrier frequencies. PIM interference that falls in the receive band of a wireless system elevates the noise floor resulting in high dropped call rates, call blocking, slow data transmission speeds and decreased system capacity.Kaelus is the industry leader in Passive Intermodulation test solutions. Since 1996 Kaelus has supplied RF equipment manufacturers around the world with precision IEC compliant test equipment to perform this critical test. From initial product design through high-volume manufacturing, Kaelus offers a wide range of PIM test solutions that enable equipment manufacturers to quickly and confidently verify the performance of their products.
-
product
Coaxial Switches
Dow-Key Coaxial RF switches are employed in RF testing equipment and large RF communication systems and networks to efficiently route microwave signals or RF energy within a transmission line. Our Coaxial RF switches route RF signals over a broad bandwidth from DC to 40 GHz, and are now offered with a Low PIM option to improve passive intermodulation levels from -110dBc (standard switch) to -160dBc.
-
product
2-port Battery Portable Passive Intermodulation Analyzer - iXA Series
iXA
The Kaelus iXA Series Passive Intermodulation (PIM) analyzer is a dual-port, battery powered PIM Test Analyzer. It supports multiple test scenarios such as testing at the top of the tower, the base of the tower, rooftop, in-building for DAS systems and external PIM Finding.No other PIM tester has ever been integrated to this level! The iXA includes a network of electronic switches to change from one-port to two-port measurement seamlessly. In addition, with integrated Range-to-Fault (RTF) on each port, the user can first troubleshoot the system for internal PIM. Then, without reconnection, the user can progress with the external PIM process, making the entire process much more efficient.With integrated RTF on each port, the user can collect four times more range-to-fault data than the standard 1-port PIM Finder solution. Thus, the user can easily locate and swiftly eliminate the strongest PIM source.
-
product
Low PIM Coaxial Switch, DC to 26.5 GHz, SP6T
87106R
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87106R is a low PIM SP6T coaxial switch, operating from DC to 26.5 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
Low Passive Intermodulation (PIM) Coaxial Switches
Low Passive Intermodulation (PIM) Coaxial Switches
-
product
Low PIM Coaxial Switch, DC to 4 GHz, SP6T
87106P
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87106P is a low PIM SP6T coaxial switch, operating from DC to 4 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
Low PIM Coaxial Switch, DC to 26.5 GHz, Transfer
87222R
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87222R is a low PIM transfer coaxial switch, operating from DC to 26.5 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
Low PIM Coaxial Switch, DC to 20 GHz, SP4T
87104Q
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87104Q is a low PIM SP4T coaxial switch, operating from DC to 20 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency and ultimately maximizes test throughput.
-
product
Low PIM Coaxial Switch, DC to 20 GHz, SP6T
87106Q
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87106Q is a low PIM SP6T coaxial switch, operating from DC to 20 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
Low PIM Coaxial Switch, DC to 4 GHz, SP4T
87104P
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87104P is a low PIM SP4T coaxial switch, operating from DC to 4 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
Low PIM Coaxial Switch, DC to 26.5 GHz, SP4T
87104R
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87104R is a low PIM SP4T coaxial switch, operating from DC to 26.5 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
External/In-Building Antennas
Pulse’s External and In-Building antenna solutions are used worldwide, providing organizations and Public Safety entities with the coverage that they rely on every day. In both portable and fixed designs, for a variety of frequencies UHF, VHF, 4G LTE/5G, WiFi 6e, GNSS and more, our External/In-Building antenna products are critical to a network’s functionality. Our V-Thinity and Clarity series antennas offer sleek low profile, aesthetically pleasing designs that can be implemented in a variety of solutions throughout in-building applications. Our portable antennas are designed and tuned specifically to work with your handheld radios and devices of choice. Pulse’s capability to adhere to Passive Intermodulation (PIM) requirements while maintaining carrier grade quality has made us a leader in the In-Building market. You can search through our selection of catalog External/In-Building products using the table below to extend your wireless coverage.
