Filter Results By:
Products
Applications
Manufacturers
-
product
Combustible Monitor
SMC 5100-02-IT
The SMC 5100-02-IT gas sensor monitors combustible gases such as Methane, Hydrogen, Propane, and others. It is based on catalytic bead technology, a consistent and reliable method of detection that offers excellent response times to the target gases. The 5100-02-IT sensor offers multiple communication outputs including 4-20 mA and Modbus RTU.
-
product
Communication Test Software for MODBUS RTU
ComTest Pro
ComTest Pro Communication Test Software for MODBUS RTU Devices via Serial and Ethernet. This complementary program allows users to test and troubleshoot MODBUS RTU communication by sending single or multiple read or write commands to the device. The software offers comprehensive data-logging, data-formatting and error checking features.
-
product
Ethernet to Modbus RTU Interface
Model 9099
* Use Modbus TCP/IP, VXI-11, or Raw Sockets (Telnet) or to control Modbus RTU slave devices.* No special driver required which eliminates driver problems.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Interfaces with PLCs or any Modbus TCP/IP Controller.* Fully VXI-11 compliant.* Works with Agilent, NI and Kikisui VISA libraries.* Internal webserver with sample Modbus device control pages for Watlow F4, F4T and EZ-Zone Controllers.* Network connectivity eliminates GPIB Bus Extension problems.* Allows multiple users to access the Modbus network or devices.* 9099 is a 2x to 5x faster than the 8099 and includes a new Modbus device control page.
-
product
Handheld Serial Data Analyser
SDA-02
Non-intrusively displays, captures and analyses electrical asynchronous data. Directly accepts RS232, RS485/422 and CMOS/TTL signal levels. Modbus over Serial Line protocol capability (RTU & ASCII), automatically checks & generates CRC/LRC, can act as master or slave.
-
product
Magnetostrictive Level Transmitter
DM231
The Drexelbrook DM231 is an explosion proof liquid level transmitter offering high accuracy measurements based on the magnetostrictive sensing technology.The DM231 comes with a Modbus RTU digital output (optional analog output converter available) for total level, interface level and temperature sensor outputs. Sensors are available in 316SS rigid designs with a choice of single or dual NPT mountings. Temperature sensors are evenly distributed over the active length of the rigid 316SS tube.Due to a wide selection of floats and mounting accessories this level transmitter fits virtually any application.The DM231 level transmitter is FM approved for Class 1 Div. 1, Zone 1 Explosion Proof hazardous area installations. It is easy to install and requires no calibration.
-
product
Modbus Controllers
Datexel has a range of Modbus RTU Masters, Slaves, Controllers, Data Loggers and Modbus remote displays. The DAT9000 is a Modbus RTU Master with RS485, RS232 and Ethernet Interfaces. The DAT9000IO is similar to the DAT9000 but it has digital input and outputs. The DAT9000DL has an additional Data Logging facility and the DAT9000DLIO has both Data Logging and digital IO. The DAT9011 is a Modbus Master with 2 analog inputs which can chose from Thermocouple's, RTD's, Potentiometers, mA and mV's. It also has 2 outputs which can be mA or voltage. The DAT9011 can also accept digital inputs and provide 2 SPDT relay outputs. The DAT9011DL also has a Data Logging facility which can store up to 8gb of readings on a thumb drive.
-
product
Modbus Data Acquisition
The Datexel range of Data Acquisition equipment includes Modbus RTU Masters and Slaves, Modbus Input, Modbus Output Modules, Modbus Isolation Modules and Modbus Repeaters. The range also includes converters (RS485, USB, RS232, RS422, TCP-IP). By combining these units with the DAT3000 and DAT10000 series a complete solution for your Data Acquisition can be found from Datexel. The DAT9550 is a remote Modbus display unit that can be programmed to accept data from Modbus slaves or masters such as a PLC or the DAT9000 range of Modbus controllers.
-
product
Modbus Plant Simulator
If you are an Industrial Control engineer or technician dealing with Modbus RTUs, PLCs, Drivers and SCADA servers, you must have Modbus TCP Plant Simulator is your toolbox. With this tool, you can test and verify your SCADA tag names, IO Server mappings, Modbus addresses, alarms, visualization displays, historians, reports, data communication channel throughput, controls, and more without deploying even one RTU or PLC.
-
product
Modbus RTU Analog Input
Provide direct connection to a wide variety of sensors to any host with an RS232 or RS485 port. The modules perform all signal conditioning, scaling, linearization, and A/D conversion. They each contain some discrete digital I/O lines and can measure signals such as:
-
product
Modbus RTU Analog Input Modules
The Datexel range of Modbus RTU analog input cards for both RS485 and RS232 with Modbus or ASCII protocol can be combined with the DAT9000 series of Modbus Masters. A choice of input cards or modules are available and have various optional inputs such as Voltage, Current, Thermocouples, RTD, and Resistance. Also a choice of 2, 4, 8 channel options are available. The DAT3011 is a Modbus RTU Slave with 1 selectable universal input (Thermocouples, RTD, mV, RTD's or Resistance), 2 x 4-20mA or 0-10V input and 2 x4-20mA outputs. The DAT3011 also has 3 digital inputs and 3 relay outputs. Each module is isolated from each other and is set up using the DAT3000 software Development package which is free of charge from the Datexel download web page. Datexel also has universal input modules. An 8 channel analog input card is available making the DAT3000 series a very economical solution to large and small scale Data Acquisition. Combining these analog input cards with the analog output cards, the digital input/output cards and the communication devices make Datexel the smart choice where Data Acquisition is required.
-
product
MODBUS RTU Test Software
MODBUS RTU Communication Test Program that helps users troubleshoot MODBUS RTU Communications. The software supports function codes, #3, #6 and #10(hex)
-
product
Modbus to DeviceNet Converter
D485
The D485 Modbus to DeviceNet Converter acts as a gateway between a Modbus RTU network and a DeviceNet network. Integration of Modbus devices into DeviceNet networks is enabled without loss of functionality, control, and reliability, both when retrofitting to existing equipment as well as when setting up new installations.
-
product
Modbus to Profibus Converter
P485
The P485 Modbus to Profibus Converter acts as a gateway between a Modbus RTU network and a Profibus-DP network. Integration of Modbus devices into Profibus networks is enabled without loss of functionality, control, and reliability, both when retrofitting to existing equipment as well as when setting up new installations. The P485 Modbus to Profibus Converter is an external DIN-rail mounted device which provides Profibus network connectivity to Modbus devices via a serial RS232/RS422/RS485 interface.
-
product
Modbus Utility
A test tool of Modbus connection. Support Modbus TCP, Modbus RTU, Modbus ASCII connections. Support Modbus Functions: 01: Read coil status. 02: Read input status. 03: Read holding register. 04: Read input status. 05: Write single coil status. 06: Write single holding register.
-
product
Multifunction Meters
Measures V, A, PF, Hz, KW, KVA, KVAr, Kwh, KVAh & KVArhTRMS MeasurementCan be used for Continuous MonitoringAuto / Manual Scroll Display (User Selectable)State of Art Microcontroller DesignPortable, Handy, Plug-n-Play and Easy-to-useLCD Display with BacklightRS-485 5KV Isolated Port (Optional) with MODBUS RTU Protocol (Optional)POWER MASTER Software for MIS Reports (Optional)
-
product
Networked Absolute Inclinometer
T7
The T7 is available in several interface and protocol options. The physical interface can be RS232, RS485 or US Digital's CAN (Controller Area Network). The protocol can be either US Digital's serial protocol or Modbus RTU. The RS232 version supports a single T7 with up to 100 ft of cable. For users that need longer cable lengths or multiple T7s on a single bus, the RS485 or US Digital CAN (Controller Area Network) version can be used. The USD-CAN protocol allows a network of up to sixty-four T7s to be connected to a single host. Power for each T7 is supplied over the CAN network cable. The host accesses the USD-CAN T7s through US Digital's low cost CANA-232/CANA-485 adapter module. This module allows the host to access each T7 on the network using simple, easy serial port commands, just like the RS232 version. The RS485 version supports up to 32 T7s on the bus.
-
product
Oxygen Analyzer
DT3000
The Datatest Model DT3000 is a Zirconia sensor, microprocessor based, oxygen analyzer. The DT3000 comes with probe configurations for temperatures up to 3200F. The microprocessor based controller provides long-term stability and reliability, plus optional features for controlling back purge, calibration gas injection, and self-calibration. 4 - 20 mA output and Modbus RTU serial port are standard. The DT3000 is available in either a NEMA 4 wall mount or panel mount configuration.
-
product
Wiring Boxes
Radio receiver for heating / cooling systems equipped with an integrated antenna, an output with SPDT relay and an RS485 Modbus® RTU slave communication port.
-
product
Metering
Based on our field experience, we have developed one of the EASIEST TO INSTALL meter interfaces on the market today. If you have an electric, gas, steam, or water meter that is able to output data via Modbus RTU or Modbus TCP, then we probably have a pre-made template that converts your meter''s data to BACnet/IP. We also have a product for pulse meters.
-
product
Residual Current Protection
Solutions to ensure the safety of people and installations against any ground currents. Available with ultra-immunized system as an essential solution to avoid financial losses due to outages caused by inadvertent trips. Specially designed to protect industrial installations in AC networks (type A), installations with both AC and DC components and DC-only installations (type B). Available with RS-485 communications (Modbus RTU) and remote control inputs/outputs.
-
product
Self-reclosing Overcurrent And Residual Current Protection
Wide range of solutions to guarantee personnel safety as well as maximum service continuity in the event of a ground current or breaker trip, with automatic reconnection of the installation. Available with RS-485 communications (Modbus RTU) and remote control inputs/outputs.
-
product
4 Digits Temperature(TC) Meter
CM1-TC
Chuan Sheng Electronics Co., Ltd.
CM1-TC Thermocouple Temperature Meter has been designed in simple function and 4 digital 20.0mm LED displays with economic cost.They are can be programmed by tact switches that are hidden in front panel.They are also available to option relay output or an analog output or RS485(Modbus RTU Mode) communication.
-
product
Digital Panel Meter
CM3-VA7
Chuan Sheng Electronics Co., Ltd.
CM3-VA7 is a multifunctional 3-phase voltage/ current meter.With 3 phase voltage or current display at the same, configurable display range via front buttons, anti-inference design, reliable quality and easy to use and install CM3-VA7 also has multiple I/O functions including 3 relay outputs, an analogue output and a RS485 communication port running the Modbus RTU Protocol.
-
product
Digital Panel Meter
CM3-VA9
Chuan Sheng Electronics Co., Ltd.
CM3-VA9 is a multifunctional 3-phase voltage/ current meter.With 3 phase voltage or current display at the same, configurable display range via front buttons, anti-inference design, reliable quality and easy to use and install, CM3-VA9 also has multiple I/O functions including 6relay outputs, 3 analogue output and a RS485 communication port running the Modbus RTU Protocol
-
product
Digital Panel Meter
VAM
Chuan Sheng Electronics Co., Ltd.
VAM Voltage & Current Meter has been designed with high accuracy dual channels(isolated) measurement, dual display and communication of 0~600V and 0~10A for DC/AC/TMRS. In compact size(48 x 96mm)● Build in mathematic function such as Addition / Subtraction / Multiplication / Division / high or low selector in 2 channels input to meet various testing equipment inquiry.They are also build in 4 Relay outputs, 1 Analogue output and 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of industrial applications.
-
product
6 Digit Weighing Controller
A6-SG
Chuan Sheng Electronics Co., Ltd.
A6-SG weighing controller has been designed with high accuracy measurement (24bit A/D), 6 digital display, flexible I/O functions and communication port for general weighing application.They are also build in 4 Relay outputs, 4 External Control Inputs, 1 Analogue output and 1 RS485 (Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of industrial applications.They was designed the tracking zero and tracking stable function in programming level. According to the system, user can set the function to get the suitable reading.According the purpose, the 4 relays can be selected individual for feeder, discharge, peak, or alarm in 7 control modes.
-
product
4 Digits Temperature (RTD) Meter
CM1-TR
Chuan Sheng Electronics Co., Ltd.
CM1-TR RTD Temperature Meter has been designed in simple operation and 4 digital 20mm LED display with economic cost.They are can be programmed by buttons that are hidden in front panel.They are also available to option relay output and an analog output or RS485(Modbus RTU Mode)communication.
-
product
4 Digit Temperature Meter (5 Channels)
CM1-TX5
Chuan Sheng Electronics Co., Ltd.
RS-485 Modbus RTU protocol (with communication LED indicator)RS-485 address 1~255Communication Baudrate 9600, 19200, 38400, 57600, 115.2KParity check N81, N82, E81, O81Input 5 channels of signal selectable：thermocouple/PT100.5 channels of input can be set to play 1~10 seconds loop display.1~5 channels of display value limits can be set, and the number of channels of carousel display screens can be set by yourself.5 channels of input signals with LED unit cycle display.Standard 2 groups of alarms Hi, LO with communication LED indicators to ensure the normal operation of the field system.Suitable for HVAC refrigeration and air conditioning PLC, DDC, PC brands to achieve remote real-time monitoringCan be used in solar panels, medical control, clean room, ice water host, boiler, motor, chemical plant, power plant, school energy-saving control, remote control of power monitoring panel
-
product
5 Digit Programmable Speed/Velocity Meter
CM1-RL
Chuan Sheng Electronics Co., Ltd.
CM1-RL series provides a simple economic programmable speed/velocity table, it 20.0mm, 5-digit LED display, press the key to set the display range and its anti-jamming design and reliable quality, simple installation, you can meet the needs of general measurement of speed/velocity.This instrument also has 2 group relay outputs, 1 analog output, or 1 groups RS485 (Modbus RTU mode) communication features three a (More features please refer to page description). Operation press the inner design, the more human-no action can be avoided, especially suitable for all kinds of machinery used.
-
product
4 Digit Process Meter
CM1-PR
Chuan Sheng Electronics Co., Ltd.
CM1-PR 4 Digits Process Meter has been designed in simple function and 4 digital 20.0mm LED displays with economic cost.They are can be programmed by tact switches that are hidden in backside of front bezel.They are also available option of 2 Relay outputs, 1 Analogue output or 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of industrial applications.
