Filter Results By:
Products
Applications
Manufacturers
Laser Interferometers
measure distances to within 1nm. Ligo can measure less than a ten-thousandth the charge diameter of a proton.
-
product
PCI Three-Axis High Performance Laser Board with External Sampling
N1231B
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
product
PCI Three-Axis Laser Board
N1231A
The Keysight N1231A PCI Three-Axis Laser Board is a register based PCI bus board that implements three axes of laser measurement for position monitoring and closed-loop servo control. The hardware outputs, optimized for connection to a DeltaTau PMAC servo control system, provide parallel digital position data at rates up to 4MHz. The same position data along with velocity data is available over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
product
Fixed Wavelength CW Laser Source (DFB)
Laser 1200 Series
The Laser 1200 Series is a highly customizable fixed-wavelength Continuous Wave (CW) laser source available in a wide range of wavelengths and powers.With seamless PXI integration, it can be easily integrated into new or existing PXI test setups. Save space, lower your costs and improve testing efficiency while delivering reliable and repeatable results in production or research environments.
-
product
Tunable Laser Source - PXI
Laser 1000 Series
The Laser 1000 Series PXIe module is a Continuous Wave (CW), tunable laser source offering high-power output, narrow 100kHz linewidth and 0.01pm resolution tunability.With seamless PXI integration, it can be easily integrated into new or existing PXI test setups. Save space, lower your costs and improve testing efficiency while delivering reliable and repeatable results in production or research environments.
-
product
Tunable Laser Source - MATRIQ
The Laser 1000 Series is a fully-compliant micro-ITLA laser with up to four channels in a compact benchtop form factor.Offering 0.01 pm resolution tunability across C or L bands, exceptional power accuracy up to 16.5dBm, and optional dither suppression, this is a versatile and cost-effective general purpose instrument.
-
product
Fixed Wavelength CW Laser Source (FP) - PXI
Laser 1100 Series
The Laser-1102 is a Continuous Wave (CW) laser source offering high power 850 nm output into multimode fiber with stable output power operation.
-
product
Fixed Wavelength CW Laser Source (FP) - MATRIQ
The Laser-1102 is a Continuous Wave (CW) laser source offering high power 850 nm output into multimode fiber with stable output power operation.
-
product
Optical Wavelength Meters
Optical wavelength meter that uses a He-Ne laser as reference wavelength and employs the Michelson interferometer method, providing high-accuracy measurement. It can measure emission center frequencies of LDs for DWDM with high resolution and accuracy.The 8471 even provides a high sampling rate of 10 times per second, and is suitable for oscillation wavelength adjustment. In addition, its deviation display function allows wavelength variation to be measured with high resolution and accuracy.
-
product
Wavelength Meter
HighFinesse/Ångstrom offers sensitive and compact wavelength meters with a large spectral range for high speed measurement of lasers. The optical unit consists of temperature-controlled Fizeau-based interferometers that are read out by photodiode arrays. The high absolute accuracy is achieved by use of solid state, non-moving optics.
-
product
Cylindrical Crankshaft/Camshaft Gage
1200
The Adcole Model 1200 Cylindrical Coordinate Measurement Machine (CCMM) is a highly accurate gage for measuring camshafts, crankshafts and other cylindrical parts that feature tight part tolerances. The system employs a proprietary laser interferometer technology to deliver precise radial and length measurements.
-
product
Laser Interferometer
1200LX
The Adcole Model 1200-LX is a high-speed, high-precision gage designed to measure crankshafts, camshafts, pistons, and other cylindrical components in demanding production environments. Simple to operate, with comprehensive, easy-to-understand pass/fail output reports, the Model 1200-LX is vital for verifying part tolerances, minimizing scrap, flagging potential quality issues, qualifying grinders and machining tools, and helping to eliminate quality breaches.
-
product
Interferometric Laser Encoders
The RLE system is a unique, advanced homodyne laser interferometer system specifically designed for position feedback applications.
-
product
Machine Calibration and Optimisation
Renishaw's laser interferometer and ballbar measurement systems assess, monitor and improve the static and dynamic performance of machine tools, co-ordinate measuring machines (CMMs) and other position-critical motion systems.
-
product
Dynamic Laser Interferometer
DynaFiz
Purpose built for reliable interferometry in vibration-prone environments; versatile and flexible enough to address a wide range of application needs from high-end telescope testing to live phase feedback for active alignment of optical systems.
-
product
Optical Spectrum Analyzer
an optical spectrum analyzer for analyzing short wavelengths from 350nm to 1000 nm. Because it adopts a Fourier spectrum system with a Michelson interferometer, the 8341 can measure the coherence. With its narrow wavelength resolution of 0.01nm * , the 8341 is very effective for the evaluation of not only CD/DVD laser diodes, but also for blue-violet laser diodes. In addition, the built-in He-Ne laser acts as a wavelength reference to ensure a high wavelength measurement accuracy of ±0.01nm * . Finally, with its fast 0.5s * measurement speed, the 8341 is ideal for building into systems for mass production and evaluating temperature characteristics of system components.
-
product
Multi-Axis Laser Interferometer
The award-winning XD Laser is a multidimensional laser measurement system that simultaneously measures all 21 degrees of freedom including linear, angular, straightness and roll errors for rapid machine tool error assessment. Measurements Include:- Rotational accuracy- Geometric error- Angular error- Flatness- Squareness- Parallelism
-
product
Regeneration Station
This equipment is a stand-alone device that enables to coherently regenerate an optical signal allowing long-haul dissemination of an ultra-stable optical frequency reference. Its architecture is based on the heterodyne phase-locking of a narrow spectral width laser diode on the reference signal. The station is equipped with low phase noise optical interferometer that perform a thorough characterization of the phase noise accumulated by the incoming signal, and a compensation system of this phase noise.
-
product
Infrared Interferometer
M-WAVE 339 MWIR
The M-Wave 339 Infrared Interferometer is a state of the art LUPI (Laser Unequal Path Interferometer) operating at 3.39 micrometers. It is the ideal instrument for testing mid-wave infrared imaging components/systems and optical material homogeneity.
-
product
Laser Interferometers & Calibration Systems
Keysight Technologies is a world leader in the design and manufacture of laser interferometry systems, advanced electronic measurement systems, high-precision optical components, complex monolithic optics (CMOs), and opto-electronic systems design for the most demanding metrology applications. Keysight systems offer high precision in a wide dynamic range, the ability to simultaneously measure a position with multiple degrees of freedom, and the highest accuracy available in both air and vacuum systems.
-
product
Laser Interferometers
ZYGO laser interferometers support and enable the most demanding metrology applications in industries from semiconductor and lithography to space-borne imaging systems, cutting-edge consumer electronics, defense-related IR and thermal imaging systems and ophthalmics.
-
product
Fibre Optic Laser Encoders
The RLE system is a unique, advanced homodyne laser interferometer system specifically designed for position feedback applications.
-
product
Universal (ID/OD) Measuring Instruments
Pratt & Whitney Measurement Systems, Inc.
The most popular ID/OD instrument in the world. Automatic probe movement with a push of a button. High accuracy is maintained by its laser interferometer, zero Abbe offset design, and large measuring table with swivel, center, tilt, and elevation control knobs.
-
product
Inside Dimension (ID) Measuring Instruments
Pratt & Whitney Measurement Systems, Inc.
High accuracy is maintained by its laser interferometer, zero Abbe offset design, and large measuring table with swivel, center, tilt, and elevation control knobs.
-
product
Laser Interferometers
Measurements of the length displacement or yawing and pitching, measurements of rotation angles, measurements of overshoots during vibrations or when stopped and of uneven speed, etc. can be handled. Length measuring instruments can be used for a variety of purposes, including precise inspection of heavy duty equipment.
-
product
50% Beam Splitter BK7, Fixed Horizontal-Bend Mount
E1834G
The E1834G is a 50% beam splitter in a high performance horizontal mount that offer the high pointing stability for Keysight laser interferometer measurement system. The 8 flexure feet are designed for stable beam pointing.
-
product
High-Resolution VMEbus Laser Axis Board
10897D
The 10897D High-resolution VMEbus laser axis board provides excellent resolution of up to 0.3 nm with a high resolution interferometer. The data age uncertainty is dramatically reduced allowing extremely accurate measurement and control of moving systems. The very high data rates accommodate high-bandwidth and high-performance closed-loop applications. Configured with appropriate lasers and optics components, the 10897D supplies unsurpassed positioning accuracy for dynamic measurement.
-
product
Laser Head
5517C
The Keysight 5517C is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Option 009 allows a larger angular range of measurement by providing a 9 mm beam diameter for use with three-axis interferometers. Please contact Keysight for custom requirements.
-
product
Angular Interferometer
10770A
The Keysight 10770A Angular Interferometer is a high accuracy plane mirror interferometer ideal for use in precision calibration applications. Used with the 10771A Angular Reflector in an 5530 Laser Calibration System, the interferometer measures pitch and yaw motions along each axis that a machine tool or measuring machine travels. The system can help quickly locate and evaluate unwanted angular motion.
-
product
1/4-Inch Cube Corner
10713D
The Keysight 10713D is one component of a family of measurement optics that tailor interferometer systems for the physical layout and measurement requirements of individual applications. Configured with appropriate laser head and system electronics, the optics are part of a precise positioning system that improves product quality, increases yields, and facilitates manufacture of precision products.
-
product
67% Beam Splitter BK7, Fixed Horizontal-Bend Mount
E1834J
The E1834J is a 67% beam splitter in a high performance horizontal mount that offer the high pointing stability for Keysight laser interferometer measurement system. The 8 flexure feet are designed for stable beam pointing.
