Filter Results By:
Products
Applications
Manufacturers
-
product
Carrier Card
VIPC627-ET
VIPC627-ET is a 6U VME carrier card with four IP slots and extended temperature range. Two 50-pin, 0.1 inch flat ribbon cable connectors mounted in the front panel provide access to all IP I/O lines. Also, all I/O lines of 'IP D' are routed to VME P2 and 14 user selectable I/O lines of 'IP C' can be routed to VME P2 via a jumper field.
-
product
Connector Adapter
MCA-ST connector adapter for the connection of micro plugThe connector adapter allows the direct connection of fine-pole connectors on circuit carriers or jumpers. The adapter is guided over the connector housing, which overcomes the tolerances of carrier and mounting.
-
product
Connectors, Jumper - Black
INT-10901
Jumper for 0.1" (2.54mm) spaced headers. These are also known as a 'shunt'. These mate with the 0.1" square-pin headers and are the 'open' frame style. RoHS compliant.
-
product
Deci-Center™ Jumpers
Series 112, 113 & 114
Deci Center Jumpers. Reliable, electronically tested solder connections. Pitch bars help maintain .100 [2.54] conductor spacing. 10-color cable allows for easy identification and tracing.
-
product
Deci-Center™ Jumpers
SERIES 150/151
DECI-CENTER JUMPERS. Pitch bars help maintain .100 [2.54] conductor spacing.Consult factory for jumper lengths under the specified minimum length.
-
product
DIN Backplane
VECTOR Electronics and Technology, Inc.
Universal (uncommitted) multilayer backplanes are designed for unique one of a kind applications requiring custom pin-out wiring from connector to connector. Each individual connector pin must be "assigned" by connecting to adjacent power or ground pins with wire or jumpers. Power or Ground input through a labeled series of power taps (screw terminals) along to top and bottom of the board.
-
product
DIP-ER™ Logic Jumper
Series 115, 116, & 117
DIP-ER Logic Jumper. Reliable, electronically tested solder connections. Protective covers are ultrasonically welded on and provide strain relief for cables. DIP-ER Logic jumper wiring is point to point. Consult factory for other wiring needs.
-
product
DIP Jumpers
Series 100 thru 111
DIP Jumpers. Aries offers a wide array of DIP jumper configurations and wiring possibilities for all your programming needs. Protective covers are ultrasonically welded on and provide strain relief for cables. 10-color cable allows for easy identification and tracing.
-
product
Economy Mini-Link™ Miniature Jumper
Series ME-100
Economy Mini-Link Miniature Jumper. Mini-LinkTM miniature jumpers are useful for jumpering .025 [.63] square pins on .100 [2.54] centers. Their miniature size makes it possible to stack one on top of the other.
-
product
Economy Model Vertisocket™
Series 800 and 822
Thrifty Model Vertisockets with Bifurcated Contacts. These low cost VertisocketsTM are recommended for high volume vertical display mounting applications. Very useful for connection of board-to-board jumpers and for DIP switches as well as LED devices.
-
product
Flat Pin-Staked Flex Jumpers
Series 171 thru 173
Flat Pin Staked Flex Jumpers. Aries Flat Pin Staked Flex Jumpers combine thin, flexible, solid Copper conductors embedded between layers of tough, flexible, flame- retardant insulation.
-
product
Fusion Bonded Cable Jumpers
Series 152FB
Fusion Bonded Cable Jumpers. Aries Series 152FB Fusion Bonded Cable Jumpers are flexible...plug them directly into PC boards or sockets. Stranded wire conductors are fusion bonded with an overcoat of tin for easy soldering or socketing. Each jumper is shipped with protective tabs on both ends for maintaining proper conductor spacing.
-
product
High Frequency Clock Divider Board
Alliance Support Partners, Inc.
Clock Divider is designed to divide high frequency signals, up to 2.5GHz, from 4 to 256 times. It will accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms. The clock division is controlled by 4 shunt jumpers. The circuit can be disabled and the divide by counter reset with 2 control signals. The on board regulator will accept voltages from 4.85 to 15.0V. The output is capable of driving 700mV Peak to Peak into 50 Ohms.
-
product
High Impedance Differential Clock Divider
Alliance Support Partners, Inc.
he ASP-DCD-00 board is a high impedance input clock divider circuit. It is designed to provide minimum load to a clock source for frequency measurement. It accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms; it divides the input signal frequency from 2 to 256 times depending on shunt jumper selections on J3. The board requires 5VDC 500mA power source to operate. The output is capable of driving 5V TTL logic levels.
-
product
Isolated SCIM5B Analog Signal Conditioning Products
SCIM5B
BEE INSTRUMENTS offers cost- effective, isolated industrial signalconditioning modules. The SCIM5B analog modules are form, fit, and functional equivalents to similar products from other manufacturers. The product range includes a complete selection of backpanels, interface cables, racks, fuses, jumpers, power supplies, and other accessories.
-
product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
product
Low PIM Cable Assemblies
Low-PIM jumper cables feature a maximum PIM level of -155 dBc and are made with UL910 plenum-rated SPP-250-LLPL cable. The PIM levels of each cable have been fully tested with the results of those tests marked on each cable. These Low-PIM cables boast a maximum operating frequency of 6 GHz and a maximum VSWR of 1.25:1 up to 2 GHz and 1.35:1 up to 6 GHz. These Low-PIM cables are lightweight, flexible and have an operating temperature range of -55°C to +125°C and are available with 4.3-10, 7/16 DIN, N and 4.1-9.5 mini-DIN connector combinations, including right-angle connectors.
-
product
Male/Female DIP Jumpers
Series 200 thru 216
Male/Femaie DIP Jumpers. Reliable, electronically tested solder connections. Protective covers are ultrasonically welded on and provide strain relief for cables. 10-color cable allows for easy identification and tracing.
-
product
Mini-Link™ Miniature Jumper
Series ML-100
Mini-Link Miniature Jumpers. Used to jumper from row-to-row or from pin-to-pin. Their miniature size makes it possible to stack one on top of the other. A convenient test probe slot is provided as well. Mini-Links are available from the factory with or without a handle, used for ease of inserting or extracting.
-
product
MPO / MTP® Patch Cords
Multi-fiber jumpers and loopbacks deliver the performance and reliability needed in todays’ demanding high-speed broadband and data networks.
-
product
n-Line Jumpers on 0.100 [2.54] Centers
Series 152, 156 & 157
In-Line Jumpers on .100 [2.54] Centers. End connectors have Gold plated, solid Brass pins on .100 [2.54] centers. Available single-ended (Series 156), double-ended (Series 157), or bare-ended (Series 152). Reliable, electronically tested solder connections.
-
product
Passive Devices
Fiber Splitters, Muxes, CWDM, DWDM, WDM, PON, Fiber Jumpers, Fiber Attenuators.
-
product
PCI POST Code Display
post4d
During power on self-test (POST), most PC BIOSes will write diagnostic codes to port 80h or port 84h (jumper selection). Use post4d to display these codes on a dual digit LED display. Additional LEDs indicate the status of the power supply rails. Convenient business card size.
-
product
PicoBuck LED Driver
The PicoBuck LED Driver is an economical and easy to use driver that will allow you to control and blend three different LEDs on three different channels. By default, each channel is driven at 330mA; that current can be reduced by either presenting an analog voltage or a PWM signal to the board. Version 12 of the board adds a solderable jumper that can be closed to increase the maximum current to 660mA. The new voltage regulator also increased the voltage rating on the various components on the board, allowing it to be used up to the full 36V rating of the AL8860 part.
-
product
Pin-Line™ Vertisocket™
Series 0517
Pin-Line Vertisockets. For mounting components, jumpers, etc., at right angle to PC board. Available 1 to 25 positions; cuttable to any number desired.
-
product
Relay Test Jumper Kit
56810
Set includes four jumpers to fit the most popular size relays on domestic and import vehicles. Simply remove relay to be tested, insert correct jumper and insert relay into jumper. When using green four pin jumper be careful to align pins on jumper and relay correctly. No need to pierce wires or connect multiple jumper wires. Jumpers have tabs for clamping and flat pads to place test leads on. Set comes in blow-molded case for storage.
-
product
Relay Test Jumper Kit II
60610
Set includes four jumpers to fit many popular relays on Honda, Nissan, Toyota, newer Ford and GM mini micro relays as well as International trucks. Set comes in blow-molded case for storage. Simply remove relay to be tested, insert correct jumper and insert relay into jumper. When using grey four pin jumper be careful to align pins on jumper and relay correctly. No need to pierce wires or connect multiple jumper wires. Jumpers have tabs for clamping and flat pads to place test leads on.
-
product
Screw-Terminal & Power Adapter Board - DC-coaxial-jack connectivity for 1 or 2 External VDC Power Supplies
TE3202
- Provides DC-coaxial-jack connectivity for 1 or 2 external 48 VDC power supplies- Provides screw-terminal connectivity for all sense, return, & output lines- May be directly connected to the HD-DB15 on the TE3200 front panel, or extended with a standard VGA extension cable.- Provided header pins for jumpering sense & return lines to channel output & return lines.- Provides a 2-pin header for jumper configuration with only one externally supplied 48VDC input (but, halves the maximum output current)
-
product
SparkFun Digital Temperature Sensor
TMP102 (Qwiic)
We all like to know the temperature, right? Well, with the SparkFun TMP102 Digital Temperature Sensor, we've made it just about as easy as it gets. Based on the original Digital Temperature Sensor Breakout - TMP102, we've added Qwiic connectors to bring this board into our plug-and-play Qwiic Ecosystem and added an address jumper instead of breaking out the address pin. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
