Filter Results By:
Products
Applications
Manufacturers
Interposers
interconnect between one connection to another.
-
product
Diode Laser Driver
D200
The D200 is a compact, DC-coupled fast laser driver, providing up to 4 amps of regulated constant current. A built-in edge-triggered pulse generator produces up to 1 microsecond pulse widths and 2 nanosecond transition times, capable of driving lasers with forward voltages up to 9 volts. A pulse-follower mode is also provided, accommodating externally-defined trigger widths up to 100% duty continuous-wave (CW). Power, pulse width, drive current and differential triggering functions are accessible through a ribbon cable header for embedded OEM applications. A low-inductance laser drive interface permits direct laser connection or custom interposer and flex-cable attachment.
-
product
Flat Flex Test Fixtures
Z-AXIS Flex Circuit Test Fixtures are used to connect flex circuits to test equipment. 20,000 plus cycles. Using the Z-Axis Elastomeric Connector Interposer, the connection to the OEM FFC connector becomes permanent and is thereby saved from over-use.
-
product
Test & Burn-In Socket for Devices up to 13mm Square
CSP/MicroBGA
Test & Burn-In Socket. Socket is easily mounted and removed to & from the BIB due to solderless pressure mount compression spring probes which, are accurately located by two molded plastic alignment pins and mounted with four stainless steel screws. Standard molded socket format can accommodate any device package of 13mm or smaller, by using machined (for small quantities) or custom molded (for large quantities) pressure pads and interposers.
-
product
Analyzer Probes
The following probes are available for the MA51x0 and MA41x0 series analyzers. These probes are designed for low-voltage and high-speed midbus probing or probing with an interposer. The following JEDEC memory standards are widely used by these probes: DDR5 (JESD79-5), DDR4 (JESD79-4), DDR3 (JESD79-3), LPDDR5 & LPDDR5X (JESD209-5), LPDDR4 & LPDDR4X (JESD209-4), and LPDDR3 (JESD209-3).
-
product
Memory Interposers
Memory interposers for logic analyzers and oscilloscopes are ordered by memory type. Please select the memory type/technology of interest.
-
product
XMC Interposer
XMC850
The PCIE850 provides a complete test and debug solution for PCI Express Bus. Interposers and probes connect to the PCIE850 providing access to PCI Card, AMX, XMC and VPX systems.
-
product
PCI Express Card Slot Interposer
PCIE850
The PCIE850 provides a complete test and debug solution for PCI Express Bus. Interposers and probes connect to the PCIE850 providing access to PCI Card, AMX, XMC and VPX systems.
-
product
VPX Interposer
VPX850
The PCIE850 provides a complete test and debug solution for PCI Express Bus. Interposers and probes connect to the PCIE850 providing access to PCI Card, AMX, XMC and VPX systems.
-
product
PCI Express® 5.0 Interposer
OCP NIC 3.0
The Summit product family includes a wide variety of Interposer systems, designed to reliably capture serial data traffic while minimizing perturbations in the serial data stream. Probes include interposers, which are designed to capture data traffic crossing the PCI Express card connector interface, and MidBus probes, which are designed to capture traffic flowing within a PCB.
-
product
PCIE/NVME Interposers
SerialTek’s PCIe Gen3 Slot (AIC) Interposers with SI-Fi technology are specially designed test adapters that are physically placed in between the PCIe slot and a PCIe endpoint to intercept and relay a copy of the high-speed signaling and discrete data lines to the PCIe Analysis system in real-time.
-
product
Interposers and Probes
The Summit product family includes a wide variety of Interposer systems, designed to reliably capture serial data traffic while minimizing perturbations in the serial data stream. Probes include interposers, which are designed to capture data traffic crossing the PCI Express card connector interface, and MidBus probes, which are designed to capture traffic flowing within a PCB.
-
product
DIMM Interposer Probe
FS2361
The FS2361 is a logic analyzer probe used to test DDR3 DIMM memory. When used with the triggering and analysis capabilities of Keysight’s U4154/64 Logic Analyzer modules, it gives the user an extremely effective tool for debugging, testing and verifying DDR3 DIMMs.
-
product
Active Interposer
FS2660A
The FS2660A is our newest and fastest logic analyzer probe used to test DDR5 RDIMM or LRDIMM memory. It is designed to work exclusively with 2 Keysight U4164A logic analysis modules operating with CHA + CHB independent busses. This gives the user an extremely effective tool for debugging, testing and verifying DDR5 RDIMM/LRDIMMs and DDR5 Memory Channels.
-
product
DDR3 X16 Non-Stacked DRAM BGA Interposer For Logic Analyzers
W3636A
The W3636A DDR4 x16 BGA interposer allows you to gain signal access to the DDR3 signals critical to your debug and validation effort through a logic analyzer. The probe works in existing designs and eliminates the need for up-front planning or redesign. The probe connects directly to the balls of the DDR3 x16 non-stacked DRAM or with an optional 3rd party socket (not provided) enabling operation and acquisition of high-speed DDR3 signals without impacting the performance of your design.
-
product
DDR4 X16, 2-Wing, Small KOV, BGA Interposer For Logic Analyzers
W4636A
The W4636A DDR4 x16 – 2 wing BGA interposer for 96 ball DDR4 DRAM is designed for data rates up to and including 2.4 Gb/s. The W4636A probes all ADD/CMD/CNTRL and partial DQ/DQS, and it is designed for minimal KOV for space limited systems under test. The W4636A is the least expensive DDR4 BGA interposer for a logic analyzer.
-
-
product
RC BGA Interposer, LPDDR4 200-ball, Rigid, Connects Using 2x U4207A
W6602A
The W6602A LPDDR4 rigid RC BGA interposer for LPDDR4 200-ball DRAM enables capture of simultaneous read and write traffic at data rates and has been tested to 3200 MT/s. Two U4207A zero Ω, 34-channel, soft touch pro, single-ended, 4 x 160-pin direct connect probes are required to connect the W6602A LPDDR4 BGA interposer into two U4164A logic analyzer modules. The W6602A LPDDR4 rigid RC BGA interposer allows signal access to the LPDDR4 signals critical to your debug and validation effort through a U4164A logic analyzer system. The probe works in existing designs and eliminates the need for up-front planning or redesign. The probe connects directly to the balls of the DRAM using a LPDDR4 200-ball riser (included) or an optional 3rd party socket (not provided), enabling operation and acquisition of LPDDR4 signals.
-
product
DDR4 X4/x8 BGA Interposer For Logic Analyzer, Connects To 61-pin ZIF
W4643A
The W4643A DDR4 2-wing BGA interposer for DDR4 x4/x8 BGA DRAM probing takes full advantage of the quad sample state mode on the U4164A. The W4643A is the smallest BGA interposers for DDR4 x4/x8 DRAM capable of capturing simultaneous read and write traffic at data rates exceeding 3.2 Gb/s. U4208A and U4209A probe/cables connect any W4640A Series DDR4 BGA interposer directly into the U4164A logic analyzer module from 61-pin high density zero insertion force (ZIF) connectors that attach to the W4640A Series BGA interposer wings.
-
product
LPDDR3 178-ball BGA Interposer For Logic Analyzers
W3301A
The W3301A LPDDR3 rigid BGA interposer for LPDDR3 178-ball DRAM enables capture of simultaneous read and write traffic at data rates in excess of 1866 Mb/s. E5406A Soft Touch probes and U4201A cables connect the W3301A LPDDR3 BGA interposer into the U4164A logic analyzer module. The W3301A LPDDR3 178-ball rigid BGA interposer allows signal access to the LPDDR3 signals critical to your debug and validation effort through a U4164A logic analyzer. The probe works in existing designs and eliminates the need for up-front planning or redesign. The probe connects directly to the balls of the DRAM using a LPDDR3 178-ball riser (included) or an optional 3rd party socket (not provided), enabling operation and acquisition of LPDDR3 signals.
-
product
DDR4 X16 2-wing BGA Interposer For Logic Analyzers, Connects To 61-pin ZIF
W4641A
The W4641A DDR4 2-wing BGA interposer for DDR4 x16 BGA DRAM probing takes full advantage of the quad sample state mode on the U4164A the W4641A is the smallest BGA interposers for DDR4 x16 DRAM capable of capturing simultaneous read and write traffic at data rates exceeding 3.2 Gb/s. U4208A and U4209A probe/cables connect any W4640A Series DDR4 BGA interposer directly into the U4164A logic analyzer module from 61-pin high density zero insertion force (ZIF) connectors that attach to the W4640A Series BGA interposer wings.
-
product
DDR5 X4/x8 78-ball BGA Interposer For Use With U4164A Logic Analyzers
W5643A
The W5643A DDR5 2-wing BGA interposer for DDR5 x4/x8 BGA DRAM probing takes full advantage of the quad sample state mode on the U4164A. The W5643A is the smallest BGA interposers for DDR5 x4/x8 DRAM capable of capturing simultaneous read and write traffic at data rates exceeding up to 5GT/s for protocol analysis and up to 4Gb/s for DQ capture. U4208A and U4209A probe/cables connect any W5643A DDR5 BGA interposer directly into the U4164A logic analyzer module using 61-pin high density zero insertion force (ZIF) connectors that attach to the W5643A BGA interposer wings.
-
product
DDR4 BGA Interposers, DDR4 DRAM X4/x8 Packages
N2114A
The N2114A DDR4 BGA interposers provide signal access to the clock, strobe, data, address and command signals to the DDR4 BGA package for making electrical and timing measurements with an Infiniium oscilloscope. With the DDR4 JEDEC specification defined at the DRAM ballout, the BGA probe adapter provides direct signal access to BGA package for true compliance testing.
-
product
BGA Interposer, LPDDR4 200-ball, 2-wing For Logic Analyzer, Connects To 61-pin ZIF
W6601A
The W6601A LPDDR4 2-wing BGA interposer for LPDDR4 200-ball BGA DRAM probing takes full advantage of the quad sample state mode on the U4164A logic analyzer module it is compatible with. The W6601A is the smallest BGA interposer for LPDDR4 200-ball DRAM capable of capturing simultaneous read and write traffic at data rates in excess of 3.2 Gb/s. U4208A and U4209A probe/cables connect W6601A LPDDR4 BGA interposer directly into the U4164A logic analyzer module from 61-pin high density zero insertion force (ZIF) connectors that attach to the W6601A BGA interposer wings. Refer to the W6601A data sheet for complete list of LPDDR4 signals probed with the W6601A.
-
product
DDR4 BGA Interposers, DDR4 DRAM X16 Packages
N2115A
The N2115A DDR4 BGA Interposers are soldered in between the DRAM and PC board or DIMM raw card where the DRAM would normally be soldered. They are designed with the PCB or DIMM foot print on the bottom side and the DRAM footprint on the top side. The signals from the memory controller chip and DRAM are then passed directly to the top side of the BGA probe adapter where they can be accessed with the oscilloscope probes.
-
product
DDR3 MSO Probes
The DDR3 DIMM and SO-DIMM Mixed Signal Interposers connect Address, Command and Control signals of a DDR3 bus to the Keysight V-Series Oscilloscopes with the MSO option. These interposers also provide accessibility to DDR3signals for convenient analog probing.
