Filter Results By:
Products
Applications
Manufacturers
-
product
120 GHz Frequency Extender, Pulsed DC Bias
N5295AX52
The N5295AX52 is a compact and broadband frequency extender with built-in pulsed bias-tee and provides 10 MHz to 120 GHz single-sweep measurements with N5292A test set controller systemized with a PNA/PNA-X B vector network analyzer.
-
product
120 GHz Frequency Extender, Pulsed DC Bias
N5295AX02
The N5295AX02 is a compact and broadband frequency extender with built-in pulsed bias-tee and provides 10 MHz to 120 GHz single-sweep measurements with N5292A test set controller systemized with a PNA/PNA-X B vector network analyzer.
-
product
110 GHz Frequency Extender
N5293AX53
The N5293AX53 modules are compact lightweight modules designed to interface to the N5292A test set controller that is driven with a PNA/PNA-X B model vector network analyzer.
-
-
product
PC-Based Bus Platform
PXIe 3U 8 Slot
PXI (PCI eXtensions for Instrumentation) is a PC-based bus platform for measurement and automation systems. PXI uses commercial PC-based PCI bus technology while combining rugged CompactPCI modular packaging, as well as key timing and synchronization features. While derived from cPCI, PXI adds the timing and synchronization features, among other things, that were not present in cPCI.
-
product
PC-Based Bus Platform
PXI 3U
PXI (PCI eXtensions for Instrumentation) is a PC-based bus platform for measurement and automation systems. PXI uses commercial PC-based PCI bus technology while combining rugged CompactPCI modular packaging, as well as key timing and synchronization features. While derived from cPCI, PXI adds the timing and synchronization features, among other things, that were not present in cPCI.
-
product
3U Format CompactPCI (CPCI) Bus IP Carrier
CPCI-SIP-2
The CPCI-SIP is a 3U format CompactPCI (CPCI) bus IP carrier. The CPCI-SIP-2 provides mechanical support and the electrical interfaces for two single width IP modules, or a double width IP module. Multiple CPCI-SIP-2 boards may be installed in a single system.
-
product
Card Extender Bracket
VECTOR Electronics and Technology, Inc.
Skate for reception & locating of modules that have to be tested (brackets are included with all VME test adapters)
-
product
CMC test Set Extender
RXB1
RXB1 extends CMC test sets with 4 additional binary relay outputs. Each binary output channel consists of a normally open ("make") and a normally closed ("break") contact.
-
product
CobaltFx 20 GHz 4' FET RF Cable Kit
This is a set of 4 cables, standard length 4 ft, for one extender: ULC50SMSM.4 cable (4)
-
product
CobaltFx 9 GHz 4' FET RF Cable Kit
This is a Set of 4 cables, standard length 4 ft, for one extender: ULC50SMSM.4 cable (4)
-
product
Dual Channel Day/Night Thermal Biocular
Recon® B2-FO
The Recon® B2-FO multi-sensor biocular combines long-range imaging and target geo-location in a compact, portable, lightweight package. Integrate B2-FO into a remote kit for wireless operation and live video streaming. Add on a 2.5x extender in the field to increase target range to >10 km for vehicle-size targets. Delivering crisp, clear thermal and visible imagery for target identification at maximum standoff, the Recon B2-FO gives forward observers the flexibility and performance required on today’s battlefield.
-
product
DVI
Products for full digital-to-digital DVI video connection such as signal extenders, cables, and adapters.
-
product
DVI Extender via Two Singlemode/Multimode Fiber Optic Cable up to 4,920 Feet
ST-2FODVI-LC
The XTENDEX® DVI Extender via Fiber Optic Cable locates a single link digital DVI display away from a computer up to 4,920 feet using singlemode fiber optic cable and 1,640 feet using multimode fiber optic cable. Supports resolutions to 1920x1200.
-
product
DVI Extender with IR and Stereo Audio Options via One CAT5/6/7
ST-C6DVI-300
The XTENDEX® DVI Extender transmits digital DVI video up to 300 feet away from a DVI source over a single CAT5/6/7 cable. Each video extender consists of a local unit that connects to a single link digital DVI source and optional IR emitter, and a remote unit that connects to a DVI display and optional IR receiver.
-
product
Extender
3690-2
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
Extender
3690-3
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
Extender
3690-16
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
Extender
3690-17
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
Extender
3690-26
VECTOR Electronics and Technology, Inc.
Height : 6.70"Length : 5.6"Contacts : 18 Contacts each side on 0.100" centers 31 Contacts each side on .100" centersTest Points : On each connector lineCurrent Rating : 5 amps at 10°F rise
-
product
Extender
3690-12
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
Extender
3690
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
Extender
3690-22
VECTOR Electronics and Technology, Inc.
Contact fingers at one end of extender card are gold plated provides low insertion force and positive contact with printed circuit board.
-
product
Extender
3690-15
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards.
-
product
Extender
3690-6
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
Extenders & Line Drivers
Extenders and Line Drivers enable reliable, long distance signal transmission over coaxial, twisted pair, or fiber optic cabling.
-
product
Frequency Extender
DC100
The DC100 system can be installed in the HP8568B(see H96 option below) without compromising the performance of the original instrument. The spectral purity and power accuracy of the primary band ( 100hz to 1.5Ghz) are insured from corruption by careful design of the DC100 system. Additional protection of the primary band is guaranteed as the DC100 system is automatically switched off (all power removed) when in primary band operation.
-
product
Gap Cover, G12/G12x, Rack Mount
310113433
Gap cover for use with rack mounting G12/G12x Receivers. The gap cover is not required if a rack extender kit is used.
-
product
HDMI
Products for full digital-to-digital HDMI connection such as signal extenders, cables, and adapters.
-
product
HDMI Extender via One SC Multimode Fiber Optic Cable to 3,280 feet
ST-FOHD-SC50
The XTENDEX® HDMI Extender via Fiber Optic Cable locates an HDMI display up to 3,280 feet (1,000 meters) away from a video source using a single SC multimode fiber optic strand. Each extender consists of a transmitter that connects to a video source and a receiver that connects to a display.
