- Pickering Interfaces Inc.
product
PXI/PXIe Battery Simulator Module, 6-Channel, Simplified Current Sink, 750 V Isolation
41-752A-901
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
Simulators
SAE J1708/J1587
The Au SAE J1708/J1587 simulators (Gen II, V1.00A release) can simulate up to 44 most frequently used Engine/Transmission/ABS parameters, warnings and diagnostic messages. Up to six Engine MID, three transmission MID and six ABS MID can be field configured. All editions can run independently (without personal computer). This family of simulators are designed very easy to use. It is widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration to product development and product validation.
-
product
Burst Simulators
EFTG
Our test generators simulate fast transient glitches as they are defined in the standard IEC / EN 61000-4-4. The individual pulses generate a wideband RF spectrum up to 300 MHz due to the very short rise time (5ns).
-
product
Grid Simulators
A grid simulator can be used to simulate the characteristics of low-voltage mains. For this purpose, all voltages and frequencies of the supply networks occurring worldwide can be simulated. Critical states such as short-term voltage dips or voltage peaks (surge/burst) can also be generated.The integrated sequencer function enables the generation of different network parameters, e.g. distorted waveforms and intermediate oscillations. Therefore, grid simulators are well suited for testing conformity to standards and especially for determining the behaviour of electrical equipment in borderline situations. Many European and other international standards are pre-programmed for testing.
-
product
Solar Simulators
Abet Technologies offer a wide range of ASTM, IEC, and JIS standards compliant solar simulators ranging from 150W to 3kW with one sun or greater illuminated field sizes from 50 x 50 mm to 35 x 35 cm. The direction of illumination, traditional down pointing, horizontal, or vertical up pointing can be specified at the time of ordering.
-
product
Partial Discharge Detector
PXDP-II
The PXDP-II partial discharge meter is a portable device that performs detection and measurement of partial discharges in electrical devices or components. It records partial discharge measurements for analysis and diagnosis through the optional PC software. The PXDP-II can be used in various applications and complies with IEC 60270.
-
product
HiL Simulators
NovaCarts Battery
Exact cell simulation for validating battery management systems (BMS). "NovaCarts Battery" represents one of the most powerful and precise cell simulation systems on the market. This is leveraged by the modular and scalable HiL system to create optimum conditions for developing new battery management functions such as state-of-charge (SoC) and state-of-health (SoH) controls, active cell balancing and electrochemical impedance spectroscopy.
-
product
Partial Discharge Detector
PDD 100
The Insulator partial discharge detector is a state-of-the-art technology used by NASA. The Parabolic design of the disc helps to maintain and detect ultrasound from safe distance of 100 Meters. Enhanced ultrasound detection is provided to the device, by combining the features of the already proven Ultra sound sensing technology with extended range and sensing capabilities. A pistol like grip laser pointer, and rifle sights make the Insulator partial discharge detector easy to handle and use.
-
product
ESD Discharge Simulator
Model 9910 PurePulse/PinScan
Model 9910 PurePulse / PinScan is used to determine the ESD susceptibility level of electronic devices up to ±4kV. PurePulse generates ESD pulses up to 4kV for testing electronic devices for susceptibility to Electrostatic Discharge (ESD) using HBM, MM and HMM models. PinScan provides automatic sequencing of ESD testing of up to 128 pin devices, applying a discharge, thenperforming a curve-trace test to identify a failure.
-
product
ECU Simulators
Easily configurable and customizable ECU solutions. Perfect for use as gateway nodes, simulators, automated testers, and ECU replacements.
-
product
Partial Discharge Measurements
MPD 500
The MPD 500 simplifies routine factory partial discharge measurements for electrical insulation systems. Engineered with OMICRON's long time experience, the MPD 500 is optimized for routine tests in high throughput environments.
-
product
Safe Discharge Rods
These instruments will allow you to conduct the safe damp discharge of the residual charge on the cable / equipment by limiting the discharge current.
-
product
Impulse Noise Simulators
INS Series
A simulator to reproduce fast rise-up noises which are generated when switching ON / OFF electric current on the inductive load. It can be used for performance evaluation of electronic equipment upon reproduction of line noises which are intruded to the power supply lines or induced noises onto the telecommunication lines.
-
product
Partial Discharge Testing
Weshine Electric Manufacturing Co., Ltd
Using the Windows system operating platform, you can freely choose ellipse, straight line, sine wave display, two-dimensional, three-dimensional graphic analysis mode, spectrum window, Q-V-F three-dimensional characteristic window, and static detailed measurement, observation and analysis of partial discharge pulse of one-cycle test voltage .
-
product
Computer simulators
There are three computer simulators offered by INFRAMET:*SIMTERM - computer simulator of thermal imagers,*VIRTEST - computer simulator of test proces thermal imagers ( MRTD measurement)*NIGHTMET - computer simulator of image intensifier tubes
-
product
Electrostatic Discharge Generator
Beijing KeHuan Century EMC Technology Co,.LTD
Electrostatic discharge generator
-
product
Large Area Solar Simulators
The LASI Beam Turner assembly allows the output of the LASI to be projected horizontally. It attaches to to the standard LASI downward facing stand that is included in the base LASI system.
-
product
PXI Millivolt Thermocouple Simulators
Series 41-760
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channelseach channel providing a low-voltage output across two connector pins capable of providing 20mV with 0.7V resolution, 50mV with 1.7V resolution and 100mV with 3.3V resolution, covering most thermocouple types. These thermocouple simulators use two wire outputs with a remote output reference sense to ensure the modules deliver accurate low-level voltages, even if the system has common mode voltages present. In addition, each simulation channel is also able to provide an open circuit setting to simulate faulty wiring connections to a sensor.
-
product
Partial Discharge Meter
APD-LT
The APD-LT equipment is a partial discharge meter in cable accessories (heads or insulators) to improve safety and maintenance. The PD level is presented numerically in the wireless unit.
-
product
Expert Partial Discharge Detector
XDP-II™
The well-established XDP-II™ is a battery-operated portable device allowing partial discharge detection and analysis. The data is saved in its internal memory for local or further analysis on the PC-based XDP-SOFT™. Paired with the proper accessories, the XDP-II™ becomes a powerful solution for many applications such as Cable Joints and Elbows, Switchgear, Offline, Acoustic, TEV, Rotating machines, Transformer, etc…
-
product
Capacitive Discharge Testers
For IEC Testing of residual voltage after plug disconnect. The CDT-240 disconnects the line at the voltage peak and analyzes results to the requirements of various Standards, allowing quick results. Scope output for viewing decay waveform. Presets for EN 61010, EN 60065, EN 60950, EN 60601-1 and EN60335. Recommendations for Pluggable Type B equipment. NIST calibration supplied; A2LA calibration available. 16A option for testing large equipment.
-
product
Space Simulators
A6H Series
Bemco offers up-to-date space simulators incorporating all of the preferred features needed for reliable combined temperature and high vacuum testing. The A6H series includes a fully integrated and appropriately sized PCL-III Portable Liquid Chiller utilizing liquid nitrogen for cooling. The PCL-III is mounted within the A6H system structure and permanently attached to the chamber thermal shroud. Mechanical cooling is available as an option.
-
product
Module Solar Simulators
QuickSun® 800-Series
800-Series simulators are always tested, certified and results reported exactly as specified in the applicable solar simulator standards and this is being proved by a globally recognized inspection body, SGS Fimko Ltd.
-
product
EFT/Burst Simulators
Suzhou 3ctest Electronic Co.,Ltd.
High-end test instrument of EFT/Burst for new energy, which fully comply with CE and CCC certification. With a built-in three-phase five-wire automatic coupling /decoupling network EFTN 69100T, it can meet the requirements of new energy test system and high power load test. It is featured with good reliability, stable performance and easy use.
-
product
Battery Discharge Test Unit
125V DC 100A
KV Hipot Power Test Equipment Co.,Ltd
Battery Discharge Capacity Tester is used to perform discharge testing which is the verifiable method to determine actual capacity of battery systems.
-
product
Damped Oscillatory Wave Simulators
Suzhou 3ctest Electronic Co.,Ltd.
Damped oscillatory wave test system for new energy can produce repeatable transient on HV or medium voltage power cord, control line and signal line. It can meet the requirements of CE and CCC certificate. With internal three-phase five-wire high power CDN DOPN 69100T, it can conduct new energy test and high power load test with good reliability, stable performance and easy operation.
-
product
Partial Discharge Testing Equipment
AR700
PD Defect Location in High-Voltage Equipment Insulation by Acoustic Sensors To act on deteriorating insulation the source of PD must be known.The insulation defects produce partial discharges, which emits electrical impulses, radiation of electromagnetic waves as well as acoustic signals.The AR700 measures acoustic signals with multiple sensors spread over the transformer. Then the software determines the failure location using the time difference of all incoming signals. Finally, these coordina...show more -
product
Modular Solar Array Simulators
MP4300A Series
The output power of solar cells varies with numerous environmental conditions (e.g., temperature, irradiation) and operational conditions (e.g., eclipse, spin). The Keysight MP4300A Series solar array simulator enables you to test all these conditions with high accuracy. It delivers fast current-voltage (I-V) curve changes with a quick recovery time, emulating rapidly changing conditions.
-
product
Partial Discharge Measuring System
LDS-6
The Doble LDS-6 is a highly sophisticated digital measuring system for partial discharge detection and analysis. It is trusted as a valuable tool for factory and laboratory testing.The LDS-6 can be used to test a variety of high voltage apparatus. Use the LDS-6 to perform PD quality tests on motors, generators, transformers, MV and HV cable systems, switchgear and additional HV accessories.The LDS-6 complies with IEC 60270, VDE 0434 as well as various IEEE and other standards.
-
product
Solar Simulators
TriSOL CPV
Concentrating Photovoltaics (CPV) has the promise of producing solar cells with high cell efficiencies, which result in a reduction in the cost of operating a PV module. However, a CPV system requires the integration of CPV solar cells, modules and CPV optics into one efficient system. OAI’s focus is CPV cell testing methodology. The CPV cells can now be tested using OAI’s advanced standalone CPV Simulators for low dose and high dose configurations. The low dose CPV Solar Simulator provides expo...show more -
product
Customize your power system simulators
Testing requirements can vary from team to team and company to company.That's why Doble's test equipment and software solutions are customizable. We allow you to choose what functions you need in order to perform testing of protection devices and schemes.From manual testing through to high burden testing, choose the options that make sense for your budget and business requirements.
