Filter Results By:
Products
Applications
Manufacturers
-
product
Digital Durometer
TIME®5410
Beijing TIME High Technology Ltd.
TIME5410 is a digital durometer for measuring the hardness of hard rubber, plastic or elastomers.
-
product
High Flow Mass Flow Controllers
High flow thermal mass flow controllers and meters offer both elastomer and metal seals for flow rates up to 300 slm. Versions are available for standard and harsh environments where protection from water and dust is required.
-
product
High Performance UV Nanoimprint Resist
AMONIL®
UV Nanoimprint is a mechanical molding technique. A template made from quartz or a flexible elastomer with a 3D relief is brought into intimate contact with a UV-curable resist spin-coated on top of a substrate. Applying low imprint pressure at room temperature features are filled within seconds due to the low viscosity of the imprint resist. The resist is hardened via UV-light through the backside of the template. Finally substrate and template are separated. The replicated resist relief can further be transferred into the substrate via RIE-process or used as functional element.
-
-
product
Mass Flow Controllers
Enabling Productivity Through Flow Control Innovation. Our wide range of mass flow controllers are available in thermal and pressure based sensor technologies, analog and digital communication, and metal or elastomer seals.
-
product
Shore Durometer
UI-FT30
Shore Durometer is used to test hardness of rubber, thermoplastic elastomers, vulcanized rubber and other materials.
-
product
Socket Accessories (Lid Options)
GHz elastomer, spring pin and other socket technologies can accommodate different lid options depending upon the application requirement. Typical choices are swivel-lid, clamshell, double-latch, integral heatsink, etc. Custom lid solutions are also available.
-
product
Sockets
Ironwood Electronics Sockets – Embedded gold plated wire elastomer (SG) – Stamped & Etched spring pins (SBT) – Embedded silver ball elastomer matrix (SM/SMP)– Compressible silver button in polyimide (GT/GTP)– Surface mount adapters for sockets (SF)
-
product
Stainless Steel Bell Jar Chambers
MDC stainless steel bell jars are designed for use with MDC baseplates, base wells and feedthrough collars. A dovetail groove in the jar's base flange holds a Viton elastomer gasket, which makes the vacuum seal with one of the forementioned components. All stainless steel bell jars are fitted with a four inch view diameter Pyrex viewport. All vacuum welds are internal and provide UHV compatibility. For added convenience, all bell jars are fitted with a hoist or lift-ring that is welded to the chamber's domed top.
-
product
Long Travel Extensionmeters
The Instron model XL (long travel) extensometer is a precise device for measuring strain in highly extensible materials such as elastomers, semi-rigid plastics and films. Designed for use with electromechanical testing instruments, Instron XL units can be used to measure specimens elongation's up to 10 in or 250 mm. An optional of 15 in or 375 mm travel is also available.
-
product
Elastomer Socket
As a structure made of silicon and conductive powder, elastomer is a good solution for high speed, no ball damage, stable CRES, low force and high frequency testing.
-
product
Durometers
A durometer gauge or durometer tester is needed to perform a durometer hardness test procedure. Durometer devices determine the surface hardness of many different materials, including polymers and elastomers. Each durometer or hardness tester measures the depth of an indentation in the material caused by a defined force of a given geometric presser foot. The depth of the indentation reflects the hardness of the material. A general distinction is made between static and dynamic methods. In traditional static tests, the test force is applied uniformly with increasing magnitude, while in dynamic testing methods, an instantaneous load is applied.
-
product
Durometer Hardness Testing
Materials Evaluation and Engineering
Durometer testing is used to determine the hardness of thermoplastic elastomers, vulcanized rubber, elastomeric materials, cellular materials, gel-like materials, and other plastics that are unsuitable for measurement by conventional Rockwell or microindentation hardness testing.
-
product
Material Analysis
Analyzing physical and chemical properties of organic and inorganic materials to provide useful information for the identification of contaminants and unknowns.Material verification and confirmationMaterial performance and suitabilityInvestigative failure analysis and chemical decomposition/degradationAsbestos IdentificationTensile testing, hardness, dielectric breakdownAccelerated aging of materials - coatings, polymers, elastomers and textiles
-
product
Solderable Individual Conductive Elastomer Pin
The World’s First Solderable, Individual Conductive Elastomer Pin
-
product
GHz Elastomer Sockets
Ironwood’s GHz BGA & QFN/MLF sockets are ideal for prototyping and testing almost any BGA or QFN device application. These ZIF sockets provide excellent signal integrity yet remain cost effective. Innovative elastomer interconnect technology that delivers low signal loss up to >40GHz and supports BGA or QFN/MLF pitches down to 0.3mm was utilized in these sockets. GHz BGA sockets are mechanically mounted over a target system’s BGA lands using mounting and alignment holes at proper locations (page 2 of the individual socket drawing shows recommended PCB layout information). These low-profile sockets are only 2.5 mm per side larger than actual IC packages (industry’s smallest footprint). They support IC devices with body sizes ranging from 55mm down to 1mm. Larger body sizes may require a backing plate. If the backside of the target PCB contains capacitors and resistors, a custom insulation plate with cavities cut for those components can be designed. This insulation plate sandwiches between the backing plate and target PCB.
-
product
Abrasion Testers
Abrasion tester is used to determines the resistance of elastomers by the frictional loss of the rubber in products, such as tires, conveyor belts, hoses, footwear, floor covering etc.
-
product
Harness Design and Manufacture
When designing an underwater cable harness, there are some factors which need to be considered, and we have produced the following list as a guide for customer information:Component considerations:- Electrical requirements- Mechanical considerations- Quality requirements- Reliability- Design redundancy (contact count)- Connector selection (type and form)- Locking requirements- Backpotting requirements- Waterblocking in moldings- Cable specification- Cable jacket material and compatibility with elastomers- Abrasion resistance- Stiffness profile at termination- Connector format (straight or right angle)- Molding format (straight or at an angle)- Clearance allowance for molding and cable routing- Elastomer compatibility (eg oil filled units)- Metalwork selection re: corrosion and cathodic delamination- Surface finish for metalwork as appropriateOperational considerations:- Operating depth profile (not just max. depth)- Tensile loads- Torsional loads- Bending loads- Bend control requirements (to limit bending at termination)- Deployment and recovery loads- Dynamic loading-Flow turbulence effects.
-
product
Mass Flow Controller for Medium Flow
HFM-205 / HFC-207
The HFM-205/HFC-207, Teledyne Hastings' flexible, general purpose series of mass flow meters and controllers accurately measure and control mass flow in a variety of applications. Featuring reliability and stability, the 200 Series is chosen for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow controller compatible with most gases.The HFM-205 / HFC-207 meters and controllers have flow ranges from 0-1000 slm to flows of 0-2500 slm; provide analog outputs, are constructed of stainless steel and can be configured with normally open or normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. With a full complement of fitting and elastomer options, the HFM-205/ HFC-207 covers a wide range of high flow applications.
-
product
Mass Flow Controller for Low Flow
HFM-200 / HFC-202
The HFM-200/HFC-202 is Teledyne Hastings' flexible, general purpose series of mass flow meters and controllers. Featuring reliability and stability, the 200 Series is chosen by OEM's for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow controller compatible with most gases.
-
product
MICRO IRHD System
Hildebrand Prüf- und Meßtechnik GmbH
The MICRO IRHD SYSTEM provides hardness readings on elastomers according to MICRO IHRD. Recommended specimen thickness is 1 to 5 mm. It complies to international standards such as DIN ISO 48, ISO 48 and ASTM D 1415.
-
product
Structural Durability Solutions
Instron offers a variety of testing systems and rigs for static, quasi-static and dynamic loading of structures and components. This includes Component Test Systems, Shaking Tables, Road Simulators, Axle Test Systems, Full Vehicle Test Systems, Wheel Test Systems, Shock Absorber Test Systems, Elastomer Test System and Dynamic Torsion Test Systems.
-
product
Pneumatic Flat Grips
For tensile testing rubbers, plastics, elastomers, textiles, cloth, and paper, in specimen geometries such as plates, films, and wires, a good option is pneumatic flat grips. Quick clamping and a repeatable clamping force are advantages of pneumatic flat grips.
-
product
Viscometers
MV 2100
The Benz Mooney Viscometer (MV 2100) measures and records the viscosity of natural and synthetic rubber and plastic elastomers, including rubber in the raw or compounded state. It is also used to determine the curing characteristics of compounded rubber.
-
product
MACRO IRHD System
Hildebrand Prüf- und Meßtechnik GmbH
Durometer Hardness System provides hardness readings on elastomers and plastics with a specimen thicker than 6 mm according to IRHD and Durometer hardness. It complies to international standards DIN ISO 48, ISO 48, ASTM D 1415 and DIN 53505.
-
product
Materials Lifecycle Management
MaterialCenter
MaterialCenter is a Materials Lifecycle Management System designed to link material specialists to mechanical simulation. MaterialCenter captures data from integrated processes to ensure full traceability across the enterprise and throughout the product lifecycle. It addresses unique process and data requirements, and drives product innovation in complex materials such as alloys, elastomers, plastics, composites, and many more. MaterialCenter works directly with many commercial CAE products and delivers on-demand commercial Databanks to engineers across the industry.
-
product
Din Abrasion Resistance Tester
SG-P01D
This tester is used to determine the abrasion characters of elastomers, rubber, soft synthetics, leather. etc or is with characters of high efficiency, good reproducibility and easy operation.
-
product
Micro durometer
MD-1 Capa
High-precision measurement of micro-sized specimens with a Fully-automatic Micro Hardness IRHD System. simple operation. A hardness tester for thin and small specimens of various rubbers, thermoplastic elastomers, nonrigid plastics. Unlike conventional durometers, it enables direct measurement of the hardness of objects with higher reproducibility.
-
product
Shore Hardness Tester
HT-6510
Application: shore A is designed to measure the penetration hardness of rubber, elastomers and other rubber like substances such as neoprene, silicone, and vinyl. It can also be used for soft plastics, felt, leather and similar materials. Shore D is designed for plastics, Formica, Epoxies and Plexiglass. Application: shore C is designed for various foam and sponge.
-
product
Mass Flow Controller for Medium Flow
HFM-205 / HFC-207
The HFM-205/HFC-207, Teledyne Hastings' flexible, general purpose series of mass flow meters and controllers accurately measure and control mass flow in a variety of applications. Featuring reliability and stability, the 200 Series is chosen for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow controller compatible with most gases.The HFM-205 / HFC-207 meters and controllers have flow ranges from 0-1000 slm to flows of 0-2500 slm; provide analog outputs, are constructed of stainless steel and can be configured with normally open or normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. With a full complement of fitting and elastomer options, the HFM-205/ HFC-207 covers a wide range of high flow applications.
