Filter Results By:
Products
Applications
Manufacturers
-
product
Ignition Driver Units
A compact inductive ignition drive unit which drives two banks of five ignition coils. The drivers are controlled via direct logic signals from a host ECU and provide fire-by-fire diagnostics back to that unit via CAN. The coils can be run at voltages up to 30V with this unit in order to minimize dwell times for optimum response.
-
product
Liquid Chromatograph Mass Spectrometer
LCMS-8040
The LCMS-8040 was designed to provide significantly higher sensitivity while maintaining the high speed offered by the LCMS-8030. Ultrafast MRM transition speeds, up to 555 MRMs per second (dwell times of 1 msec and pause times of 1 msec) are achieved. In addition, the LCMS-8040 features the polarity switching at 15 msec and high speed scanning rate of 15,000 u/sec. By incorporating newly improved ion optics UF-Lens™ and UFsweeper™ II collision cell technology, the LCMS-8040 provides higher multiple reaction monitoring (MRM) sensitivity. This higher sensitivity expands the potential range of LC/MS/MS applications.
-
product
Multichannel Analyzers
A family of USB-connected, software controlled Multichannel Analyzers with 4 - input MCA with 32k resolution, > 1 M events / sec on each channel, MCS mode, RTC (option). The MCA-4 offers two multiscaling inputs with a counting rate capability of 300 MHz at dwell times as low as 70 ns.
-
product
Thickness Gauges
Precision Thickness Gauge is specifically designed to quickly and accurately measure the thickness of a variety of substrates including film, paper, board, foil, tissue and textiles.Operated via an intuitive touch screen interface the instrument will allow the user to define batch size, dwell time & measuring speed.Full test statistics can be easily viewed or printed to label for easy documentation control.
-
product
6GHz RF Signal Generator
TGR6000
0MHz to 6000MHz frequency range10Hz setability, ±1ppm frequency stabilityLocking to external frequency standard-110dBm to +7dBm amplitude, 0.1dB stepsFast stepping sweep with dwell times down to 10msList sweep of up to 1000 points of amplitude vs frequencyUser compensation tables for specific test set-upsStorage for 12 generator set-ups and 16 sweep listsCompact half-rack 2U casing uses minimum bench spaceFull remote control through RS232, USB, LAN and GPIBSignificantly lower cost than other 6GHz generators
-
product
Automotive Digital Multimeter, 1999 Count, Average, Manual Range, 3.5 Digit
72-9275
Full featured multimeter with additional functions for automotive diagnosis. Measures AC/DC voltage, DC current, resistance, frequency, dwell, tach, duty cycle and temperature.
-
product
Heat Seal Tester
HST-H3
Heat seal tester (Laboratory heat sealer) is to determine the suitable sealing parameters (sealing temperature, dwell time and pressure) for materials.
-
product
Heat Seal Tester
HST-01A
Jinan Leading Instruments Co., Ltd.
HST-01A Heat Seal Tester seals the specimen to determine the seal parameters of basicfilm, laminated films, coating paper and other heat sealing laminated films according to the requirement of relative standards. The seal parameters include heat seal temperature, dwell time, and the pressure of heat seal. Heat sealmaterials that have different melting point, heat stability, fluidness, andthickness of could show various heat seal properties, which cause obviouslydifferent seal technique.
-
product
Heat Seal Tester
HST-01
Jinan Leading Instruments Co., Ltd.
HST-01Heat Seal Tester seals the specimen to determine the seal parameters of basicfilm, laminated films, coating paper and other heat sealing laminated filmsaccording to the requirement of relative standards. The seal parameters includeheat seal temperature, dwell time, and the pressure of heat seal. Heat sealmaterials that have different melting point, heat stability, fluidness, andthickness of could show various heat seal properties, which cause obviouslydifferent seal technique.
-
product
Digital E-Gun Sweep
XYC-20
The XYC-20 E-beam evaporation controller is in a class by itself. The unit can be calibrated by the user to their specific system and e-gun. An algorithm determines the beam error from front to back and side to side within the pocket, eliminating pocket overshoot and burn-thru. The pattern control is effectively made linear saving time in programming and setup. Beam dwell time can vary at each location to compensate for variation in beam density. Six pocket sizes and two shapes can be selected.
