Filter Results By:
Products
Applications
Manufacturers
Drop Testers
determine impact resilence of packaging and products. 2) in-flight test of craft carried aloft then released.
See Also: Impact Test, Pendulum Impact, Impact Hammers
-
product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
Bit Error Rate Tester - MATRIQ
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
PAM4 Bit Error Rate Tester.
BERT-1102
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
product
Automated Coherent Receiver Tester
CoRx Tester.
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
product
MTM-Bus Tester
PXIe-1149.5
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
product
Electric Servomotor Free Fall Tester
An electric servo motor type packaged cargo drop tester compliant with "JIS Z 0202 Packaged cargo-Drop test method". It is possible to test large test pieces safely, stably and quietly.
-
product
Geotextile Cone Drop Tester
TG015
TESTEX Testing Equipment Systems Ltd.
Geotextile Cone Drop Tester, to determing the resistence of cone drop from certain height.
-
product
Heavy-load Pallet Drop Tester KD-500
KD-500
King Design Industrial Co., Ltd.
*To evaluate impact effects of shock, drop and tumble encountered in repair and handling process, so do the safety strength assessment. *The general drop test is against bottom, angle, edge and tumble. According to related specifications you can lift one side of the product by angle to make it drop freely.
-
product
Battery Drop Tester for Battery Safety Test
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's battery drop tester is used to test the drop impact performance of large, heavy-duty packaging products by simulating real surface, edge, and corner differences.
-
product
Automatic Huge Drop Tester
KD-8688
King Design Industrial Co., Ltd.
Reliability & Photovoltaic (PV) Testing Equipment.
-
product
Drop Tester
KD 688 A
King Design Industrial Co., Ltd.
*PLC control, linear motor fast speed control the height setting.*Alarm warning before testing.*Light support structure decreases the test impact.*Support dropping very smooth with dual lubrication guide.*No second impact. *A data acquisition for the impact wave record (Option).*Non maintenance request for continue operation.*According to ISTA, ASTM .....etc international standard.*Equipped edge & corner holder.
-
product
Battery Pack Drop Tester
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Battery Pack Drop Tester Relevant standards requirement:Test object: battery pack and systemTest procedure: The test object is most likely to fall in the direction of actual maintenance or installation. If it is not possible to determine the most likely fall direction, fall in the Z-axis direction, and the battery pack will fall from the height of 1 m to the concrete floor and observe for 2 hours.Accept standard: The battery pack or system has no electrolyte leakage, fire nor explosion.
-
product
Coefficient of Friction Tester
COF-01
Jinan Leading Instruments Co., Ltd.
COF-01 Coefficient of Friction Tester is applicable in static and kinetic coefficient of friction tests of plastic films, sheets, rubber, paper, PP woven bags, fabric style, metal-plastic composite strips/belts for communication cable, conveyor belts, wood, coatings, brake pads, windshield wipers, shoe materials and tyres, etc. With the material smoothness testing, users can control and adjust material quality technical indexes to meet application demands. Besides, this tester is applicable for the smoothness measurement of cosmetics, eye drop and other daily chemistry.
-
product
Drop Tester
KD-2768
King Design Industrial Co., Ltd.
Drop tester is applied to test the anti-vibration, covering-protection capability of packaging material, or product’s impact-resisting capability to determine the improvement parts of related packing design, material and structure. It contribute to promote the packing material and product’ strength. According to the result of packing drop test, you can judge whether the product has reach the required strength encountered in future. Through doing the drop testing of product independently, you’ll know its affordability to withstand external impact and assess the damage.
-
product
Coefficient Of Friction Tester
COF-02
Jinan Leading Instruments Co., Ltd.
COF-02 Coefficientof Friction Tester is applicablein static and kinetic coefficient of friction tests of plastic films, sheets,rubber, paper, PP woven bags, fabric style, metal-plastic composite strips/belts for communication cable, conveyor belts, wood, coatings, brakepads, windshield wipers, shoe materials and tyres, etc. With the materialsmoothness testing, users can control and adjust material quality technicalindexes to meet application demands. Besides, this tester is applicable for thesmoothness measurement of cosmetics, eye drop and other daily chemistry.
-
product
DC Vibration Unit Tester
BK2116
As the technology for BLDC motors advances, more advanced testing is also needed. The BK2116 DC Vibration Motor Tester was designed when of several of our clients needed to test the new generation of 3 port DC vibration motors. Using the BK2116, you can test the electrical specifications (RPM, current, drop pulse, and start up voltage) and also vibration level, and noise of motors with either 2 or 3 ports. The BK2116 can concurrently test 2 DUT's and BaKo's Test Shop software makes it very easy to set up and test. And because you use it with a PC or notebook, you can see graphs of the data as you test, and also save it to analyze later, or to analyze the data you gather over time.
-
product
Pneumatically Powered Bed of Nails Testers
Automator Pneumatic Family
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
product
Lever Handle Bed of Nails Testers
Automator Manual Family
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
product
Motorcycle Battery Testers
ELAK Motor-Cycle Battery Testers are designed for testing batteries used in motor-cycles, scooters, ATV''s, etc. These testers check the voltage drop of the battery under a fixed load and confirm the status of the battery full, weak or dead. The new generation motor-cycle and scooters are fitted with an electrical start. It is therefore very essential to test these batteries under load, to ensure that the batteries are capable of starting the vehicle.
-
product
Smoke Detector Tester
Solo 365
The fire industry’s most popular range of detector test equipment is about to get even better. Solo, the test equipment used world-wide to functionally test fire detectors has a new tester in its range – Solo 365. This exciting innovation provides fire safety professionals with an array of stand-out features which make for faster, simpler and cleaner functional testing of smoke detectors. Key features include automatic generation of smoke which ensures only the amount of smoke needed to activate the detector is produced – minimizing smoke wastage and eliminating the risk of detector contamination. In addition, Solo 365 is light in weight and has a slim-line design which allows easy access into tight spaces – making it possible to test detectors which are hard to access with other portable testers. In response to market feedback, Solo 365 features an LED torch which automatically illuminates when light levels drop, making for easy detector alignment and testing in dark environments. Smoke is generated via newly designed smoke cartridges which fit neatly into the rear of the tester. With no reliance on pressurised aerosol cans, the cartridges can be easily shipped and stored and are unaffected by new regulations, set for 2018, which will affect availability of some pressurised smoke aerosols.
-
product
Premise Toner Drop Cable Continuity Tester
RPT-AAA Series
Electronic testing tool designed to check the circuit integrity in new or installed cable up to 5,000 feet (1,500 meters) in length LED indicates DC shorts, splitters & other self-grounding devices in cable while a loud audio tone identifies the line carrying the signal Equipped with a right angle male push-on connector to maneuver in tight areas & a female push-on connector for speed toning Tool includes a pocket clip & (1) AAA 1.5V battery.
-
product
Small Objective Drop Tester
KD-208 A
King Design Industrial Co., Ltd.
Testing of Mobile phones, batteries, PDA, digital camera and other hand-held communications and IT product.
-
product
Small Objective Drop Tester
KD-208
King Design Industrial Co., Ltd.
Testing of Mobile phones, batteries, PDA, digital camera and other hand-held communications and IT product.
-
product
Negative pressure Leak Tester
SKZ1016A
Leak Tester is a kind of tester that use compression air to produce negative pressure by vacuum device totest the seal capability and processing technique of soft plastic packaging material in food andpharmaceutical industry. It also can test the specimen which has done the drop and compression test. Theproduct is designed and manufactured according to GB/T15171-94 (the Seal Testing Method for softpackaging). ASTM D 3078 Standard Test Method for Determination of Leaks in Flexible Packaging
-
product
Drop Dart Impact Tester
Qualitest offers a Drop Dart Impact Tester which is simple to use as a stand-alone, non-instrumented tester. It is used to measure impact resistance of film, sheet, and laminated materials.
-
product
Drop Weight Impact Tester
The Falling Weight Impact Tester is used to perform impact tests on plastic pipes, conforming to ISO 3127, EN744 and EN1411. Test pieces are subjected to blows from a falling striker, of specified mass and shape, dropped from a known height onto specified positions around the circumference of the test piece. The true impact rate of the batch, or production run from an extruder, is estimated.
-
product
Drop Testing Machines
Infinity Machine International Inc.
Drop Testing Machines by Infinity Machine International Inc. - for applications such as: tumble tester, drop weight impact testing machine, mobile phone roll drop tester, micro drop testing machine for mobile phone, and more.
-
product
Loading Adjustable Drop Tester Machine
CX-DL15A
Shenzhen Chuangxin Instruments Co., Ltd.
Package Impact Drop Testing Machine is used to measure the dropping impact incidence when the package in using, transportation and decorating. Labtone "1G+" project strictly ensure the accuracy. Besides precision plane drop testing, it also can undertake edge and angle test to ensure the complete performance evaluation for the package. During the products handling or transport process, there may be drop/ fall, which results in damage within the products. And this Drop Tester simulates the drop/ fall of a finished product to evaluate the damage. All the rhombohedrons, angles and faces of the products can be tested.
-
product
IEC60529 IPX1-IPX2 Vertical Drop Tester
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60529 IPX1-IPX2 vertical drop testerIPX1 uses the vertical drop of water tank, shell in the speed of 1r/min turntable, turntable axis and the specimen axis distance eccentricity is about 100mm, the water flow is 1mm/min, duration of 10 minutes. IPX2 uses the vertical drop of water tank, shell four fixed positions in the tilted 15 degrees, table does not turn, the water flow of 3mm/min, eac
