Filter Results By:
Products
Applications
Manufacturers
-
product
Data Acquisition
Data Acquisition And Control Software offers complete control over the temperature and pressure schedules of oilfield laboratory instruments from a personal computer. Digital Chart Recorders provide secure data storage and digital backup of critical test data. Previously sold as ancillary equipment on all Chandler Engineering HPHT cement consistometers, pen and paper chart recorder technology is rapidly becoming obsolete as industry demands change.
-
product
Fineness Analyzer
HN-CF100
CHANGSHA KAIYUAN INSTRUMENTS CO., LTD.
HN-CF100 Fineness Analyzer is suitable for a variety of laboratories and industrial corporation: Nonmetallic powder: coal, cement, limestone, fly ash, calcium carbonate, silicone dioxide, magnesium oxide and so on. Metallic powder: aluminum, iron, zinc, rare earth metal, alloy and so on. Others: abrasive materials, silicon carbide, flour, lithium cell materials, porcelain ingredients, coating materials and so on.
-
product
Fluid Loss
Fluid Loss testers were designed to be as easy to use as possible, with clear and intuitive controls. Once the cement slurry or mud is placed into the test cell, a programmable temperature controller increases the temperature at the desired rate. The slurry is conditioned by stirring at 150 rpm similar to a consistometer.
-
product
Hand Held Microwave Moisture MeterFor Water/Cement Ratios of Fresh Concrete
Cementometer
The James Cementometer represents a break-through in modern moisture measurement technology. By utilizing the latest microwave and microprocessor science, the Cementometer can determine the moisture content of freshly mixed cement, concrete, and mortar. Simply insert the prongs of the probe into the material to be measured and instantaneously the water cement ratio is shown on the easy to read display.
-
product
High-Temperature Strain Gages
ZWH-, ZWN-, & ZWP-Series
ZWH-, ZWN-, and ZWP-Series strain gages are designed for dynamic and limited static strain measurement at hightemperature.These strain gages are manufactured using a round wire for superior bonding ability and performance. A high-fatigue wire (Option Z) is also available on each of the gages. These gages are supplied with a fiberglassreinforced tape carrier which holds the grid and leads in place during installation and are bonded using ceramic cements or Rokide® flame spray. The shelf-life of thesegages is 9 months.
-
product
Mechanical Properties
Mechanical Properties Analyzers (MPRO) continuously measures the elastic mechanical properties (Poisson's Ratio, Young's modulus, Bulk Modulus) and the compressive strength of API cement as it cures under high-temperature and high-pressure conditions.
-
product
Medium Voltage Drives
Target markets include Oil and Gas, Water and Wastewater, Power Generation, Rubber and Tire, Mining, Cement and other industrial applications. They can be applied equally well to applications requiring Constant Torque (CT) output performance as well as the traditional Variable Torque (VT) pump and fan loads.
-
product
Moisture Meters
Sper Scientific’s moisture meters accurately read the moisture content of all types of wood but of cement, plaster, brick and concrete. Home and building inspectors rely on moisture meters to identify potential problems and damage to structures from moisture buildup. Woodworking industries, such as furniture makers, use wood moisture meters to insure a quality product.
-
product
On-line Crossbelt Analyzers
CNA Range
CNA online elemental analyzers are available in three models:*CNA³: This cross belt analyzer is designed for minerals applications that feature wide conveyor belts with deep loads and large material size. It is an open analyzer that is installed below the belt with both the neutron source and the detectors below. *CNA Pentos Cement: This cross belt analyzer is used primarily in cement and related industries. It is a closed analyzer that encircles the conveyor belt with the neutron source below the belt.*CNA Nickel: This cross belt analyzer offers real-time quality control for the nickel ore mining industry.
-
product
Thermogravimetric Analyzer
TGA801
The TGA801 is the latest generation of automated macro thermogravimetric analyzers to enter our lineup. The TGA801 maintains the core capabilities and reliability of previous generations of LECO macro TGA instruments, while providing key improvements in performance and robustness. By incorporating state-of-the-art hardware with an on-board touch-screen software platform and a rugged design, the TGA801 provides accurate, high-precision thermogravimetric constituent analysis—moisture, ash, volatile content, and LOI in various organic, inorganic, and synthetic materials. Complying with ASTM standardized methods, the TGA801 is applicable to many industries and applications including coal, cement, catalyst, foods, and feeds.
-
product
zeta potential analyzer
ZetaProbe Analyzer™
The ZetaProbe is the easiest to use, most accurate zeta potential analyzer available. Samples can be measured without dilution or sample preparation at concentrations up to 60% volume. Even the direct measurements of pastes, gels, cements, and other difficult materials are possible with the ZetaProbe.
-
product
Carbon / Water Analyzer
CW‑800
Determination of released carbon dioxide and water is a special requirement for quality control in the cement and lime industry. ELTRA’s CW-800 analyzer is designed for the precise, simultaneous determination of carbon dioxide and water in lime, gypsum and cement from trace level up to 100 % (depending on sample weight). Other sample materials include ores, soil and minerals. The CW-800 is equipped with a resistance furnace with quartz tube for sample oxidation and can provide temperatures up to 1000 °C. The temperature of the CW-800 can be set up in steps of 1 °C and the temperature is fixed during measurement. As common carrier gas in the CW-800 nitrogen is used.
-
product
Carbon / Water Analyzer
CW‑800M
ELTRA’s CW-800M analyzer is designed for fractional analysis of carbon and water in one single operation. It is based on the proven technology of the CW-800 but has a modified furnace which allows fast adjustment of the temperature in the furnace. Different fractions of carbon and water of the sample are analyzed by applying different furnace temperatures. ELTRA’s CW-800M analyzer is designed for the precise, simultaneous determination of carbon (released as CO2) and water in lime, gypsum and cement from trace level up to 100 % (depending on sample weight). Other sample materials include ores, soil, minerals, slags and waste.
-
product
Stack Gas Analyzer
ENDA-7000 Series
After decades of experience in precise stack gas measurement, HORIBA's brand new ENDA series represents the ultimate stack gas analyzer. With enhanced lower cost and reduced maintenance time, high sensitivity, and usability, we focused on the users' point of view. The ENDA-7000 is designed to continuously measure the concentrations of NOX, SO2, CO, CO2, O2, and NH3 in stack flue gas streams. The model is offered in dozens of combinations based on your measurement requirements. The ENDA-7000 uses an extractive method which measures undiluted sample gases, and is very suitable to stack gas measurements such as shale gas, LNG, or biogas and other combustion applications. The ENDA-7000 is an excellent choice for measurements in power generation facilities, boilers, furnaces, steel manufacturing, cement plants, pulp and paper mills, etc.
-
product
Air Quality Analysis
Ambient Gas Monitoring: We offer a variety of analyzers for the ambient monitoring of the criteria pollutant gases, including CO, NOX, SO2, and others such as CH4 and CO2. Source Gas Monitoring (Emissions Monitoring): Experience reliable measurement in your process for emissions compliance every time.Ambient Particulate Monitoring: Experience our monitoring technology and gain the power to do more than just inform.Emissions Calibrators: For continuous monitoring of mercury in exhaust stacks, waste incinerators, and cement kilns, or multi-gas models to control the calibration of gas concentrations.
-
product
Arc Infrared Carbon and Sulfur Analyzer
CS-8620
Wuxi Tianmu Instrument Technology Co., Ltd.
Infrared carbon and sulfur analyzer is used together with high-speed automatic ignition furnace to quickly and accurately determines the mass fraction of carbon and sulfur in steel, iron, alloy, non-ferrous metals, cement, ore, catalyst and other materials. a high-tech product integrating light, electromechanical, computer and analytical technology. It has the advantages of wide measuring range, strong anti-interference ability, complete functions, simple operation, accurate and reliable analysis results, etc. It is the ideal for measuring Carbon and sulfur in many industries. Analytical equipment.
-
product
Blockage Locators
Shenzhen Noyafa Electronic CO.,LTD
Noyafa Blockage Locator can be used in both household and engineering. The sensing range is enhanced, and it is free from external interference. It can pass through the 60cm-thick cement wall and the pipe blockage under the floor to reduce the removal area. Accurate detection and adjustable sensitivity.
-
product
Building Materials Testing
Through Stanger Testing Services Limited a wide range of services are available to the construction industry, including standard cement tests, the assessment of aggregates and cladding stone, the valuation of admixtures and the determination of the mechanical properties of most building materials.
-
product
Concrete & Cement Testing Equipment
Torontech's offers many cement products which are built to the highest quality and standards. Torontech has a large range of cement products to accomplish anything you would like.
-
product
Concrete Testing Equipment
Concrete, a composite mixture of water, aggregates, cement and sometimes additives, is the most commonly employed man-made building material in construction projects. The quality of concrete is crucial if structures are to be safe and serve the purpose for which they were designed. Consequently, the testing of fresh, hardened and in-situ concrete is vital to ensure that concrete structures comply with specifications and relevant standards.
-
product
Cement Testing Equipment
High quality cement is necessary to produce concrete and mortar that meets relevant construction industry specifications. ELE international designs and manufactures a wide range of sample preparation and cement testing equipment which complies with global standards for the assessment of fineness, consistency, setting time, workability, flow, strength, soundness, heat of hydration and chemical composition.
-
product
Oil Well Cementing
Chandler Engineering has produced the highest quality Oil Well Cementing instruments for the Upstream Oil & Gas Industry. Today, Chandler Engineering, the industry's largest instrument supplier continues its effort to help customers improve the efficiency and productivity of their drilling and production operations. Below is a portfolio of API and ISO specified instruments for testing key performance properties of oil well cements.
-
product
Building Electronic Thermometer
NF-514
Shenzhen Noyafa Electronic CO.,LTD
*Cement Concrete Professional Thermometer.*Built-in LCD Lighting Function: Working in harsh environments, clear readings.*Exquisite material selection and lightweight design.*Built-in Temperature Measuring Line, Durable and High Temperature Resistance.*Embedded Line Asphalt Temperature Measurement.*Small size,light weight, easy to carry, suitable for construction sites and field operations.*Certification. Passes RoHS, FCC, and CE compliance testing, and Noyafa is certified to the ISO 9001 standard.*100% Affordable. Manufactured in China and a lot cheaper than competitor products with similar quality.
-
product
Universal Calibrators
We offer our clients an exclusive range of Universal Calibrators which is designed and manufactured by our technical team. Our range is designed using superior quality material, and is widely appreciated for its rugged designs and durability. Also, these are presented with dual operating ability of source & sink of signals that make them appropriate for labs and process plants. Further, our assortment is extensively used in the calibration of instruments, commissioning of field instruments, repair & maintenance of filed instruments and as millimeter with limited facilities in various industries, such as chemical, cement, textile, fertilizer and automobile.
-
product
Moisture Testing
Determine moisture in concrete and other construction materials. Meter for rapid determination of moisture content in sand and other fine or coarse aggregates. moisture content in Solid Materials. Includes Meter, Test Cable and Case. Meter for the Rapid Determination of Moisture Content in Different Types of Soil. Determination of Water/Cement Content Ratio in Fresh Concrete. (Type R for Regular Water Cement Ranges. Type L for Low Water Cement Ranges.)
-
product
Slurry Preparation
Slurry Preparation Constant Speed Mixers blend cement slurry at an automatic maintained, constant shear rate in accordance with API standards. Atmospheric Consistometers are a simple and accurate means to prepare cement slurries for the testing of rheological properties, fluid loss and various other properties in strict compliance with API standards. Wettability Testers are two instruments in one; a constant speed mixer and an instrument for the evaluation of oil/water phase transition of oil-based drilling fluids as they interact with spacer and/or pre-flush systems.
-
product
Single Position Automated Electric Fluxer
Single-position fully automated electric fusion machine with a typical sample throughput of 5-7 samples per hour. Ideal for preparing fused beads for XRF analysis and solutions for AA, ICP, and wet chemistry analysis. Patent PendingTypical samples include: Cement, Clinker, Ores, Slag, Refractories, Ceramics, Catalysts, Glass, Rocks, Minerals, Soils
-
product
Precision Current Sensing Resistors
PCR4T
Precision cement resistors designed with four terminals, are distinguished by excellent long term stability & TCR. The Kelvin connections of this device allow high precision measurements even with low resistance values. PCR 4T has a non-inductive copper manganin element inserted into the ceramic case and finally sealed with a ceramic molding. This resistor has low inductance and has high pulse power.
-
product
High Power Precision Current Sensing Resistors
HPCR4T
High Power Precision Current Sensing Resistors of HPCR4T designed with four terminals, are distinguished by excellent long term stability & TCR. The Kelvin connections of this device allow for high precision measurements even with low resistance values. HPCR 4T has a non-inductive copper manganin element inserted into the ceramic case and finally sealed with a cement molding.
-
product
Whiteness Meter
Guangzhou Amittari Instruments Co.Ltd
AMITTARI l Whiteness Meter is mainly used to directly measure the whiteness value of object or powder with flat surface. It can be widely used in whiteness measurement of textile printing and dyeing, paint, chemical building materials, paper board, plastic products, white cement, ceramics, enamel, talc powder, starch, flour, salt, detergent, cosmetics and other substances. The instrument pass strict inspection and testing, conforms to the JJG 512-2002 Whiteness Meter Verification Regulation. Also conforms to GB3978、GB3979、GB7973、GB7974、ISO2470、GB8904.2、QB1840、GB2913、GB13025.2、GB1543、ISO2471、GB10339、GB5950、GB12911、GB2409 and other standards.
