- Virginia Panel Corporation
product
PCB Adapter, Receiver, TriPaddle, 64 Position, To PCB-Mounted 2x34 Pin (BERG 65496-019) Connectors
510104128
The 64 Pin Signal Receiver Module is made from Ryton® R-7 and will withstand temperatures up to 220°C. The 64 Pin Signal ITA Module is made from engineered resin and will withstand temperatures up to 150°C. Both the ITA and Receiver Modules have molded nomenclature.
-
product
Adapters
Amphenol Fiber Systems International
Amphenol Fiber Systems International (AFSI) offers a complete suite of passive fiber optic adapters to facilitate conversion from one network-based connector type to another. The small size of these adapters eliminates the need for bulky and expensive adapter cables.
-
product
Adapters
Teledyne LeCroy offers two quantumdata test point adapters as auxiliary devices for testing MHL and HDMI HEAC.
-
product
Adapters
They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
product
Adapter
HT-EM2
Hitron Americas Technologies Inc.
The HT-EM2 enables high-bandwidth trafic to be seamlessly distributed across the end-user’s home or office.
-
product
1.85mm Adapters
Pasternack 1.85mm adapter category majority are RoHS and REACH compliant. 1.85mm adapter components are part of a comprehensive adapter product line from Pasternack.Our 1.85mm adapters allow you to interface 1.85mm connectors with 1.85mm, 2.4mm, 2.92mm, 3.5mm, N, SMA or SSMA connectors. 1.85mm adapters are constructed in female to female, female to male, male to female or male to male gender designs.Pasternack's ISO 9001:2008 registered facility ships 1.85mm adapter series the same day from the broadest and deepest in stock inventory of microwave and RF parts. Excellent technical support and customer service are on hand to assist you.
-
product
Adapter
ZET 430
*Aligns sensor output signal with the FFT spectrum analyzer input;*Sends the FFT spectrum analyzer generator signal to the sensor calibration input;*Provides power supply to the sensor from the integrated ±12 V power supply unit.
-
product
Adapters
BroadWave designs and manufactures Coaxial Adapters and other coaxial RF components that are ideally suited for test, verification and system integration. Our products offer consistent performance at a low cost with an emphasis on performance and configuration flexibility.
-
product
Test Adapter
PMC-UNIV-TEST
PCI adapter for PMC with options for PCI and PMC Stack Pass through connections
-
product
RF Adapters
SMB Adapters
The SMB adapter allows connection to the SMB server to perform all the common CRUD (Create, Read, Update, and Delete) based operations for files and directories.
-
product
Test Adapter / Pneumatic Adapter
GPS testing technology offers a wide range of pneumatic adapters. The support with compressed air results in increased ease of use and larger pressures can be built up easily and thus more test needles can be contacted.
-
product
I2C Adapter
RS485
*RS485 address adjustable via DIP switch*I2C frequency adjustable up to 400kHz*I2C level shifter, I2C level from 2V to 15V*Interrupt input for external events*Simple software interface (ASCII commands)
-
product
RF Adapters
TNC Adapters
Amphenol RF offers a wide array of both in-series and between-series TNC adapters in straight and right-angle configurations. 50-ohm and 75-ohm impedance TNC adapters are available with and without panel mounting features. Popular mounting features in bulkhead, both front and rear mount, and 4-hole flange designs. 50-ohm TNC connectors have a frequency range from DC to 11 GHz. 75-ohm TNC connectors have a maximum frequency of 3 GHz.
-
product
VoIP Adapter
A VoIP adapter is a protocol converter (bridge) between analog phones and the digital (IP) network that carries voice calls.
-
product
Probe Adapters
Probe adapters provide simple and easy interface of third-party probes as well as change between the different Teledyne LeCroy Oscilloscope input and cable types (ProBus, ProLink, K/2.92 mm, BNC and SMA). Depending on the adapters, changing between the Teledyne LeCroy Oscilloscope's input type may have an effect on the overall performance of the channel.
-
product
Emulation Adapters
With some of the more advanced 32-bit microcontrollers and SoCs, the full program and data trace capabilities of the device are not made available on production silicon. Instead, semiconductor vendors provide special 'emulation devices'. These typically feature more pins than the production device, thereby providing the interface to the trace interface.
-
product
USB to TTL Adapter
SKU-012-0X
The USB to TTL adapter connects the Serial UART to the standard USB port for testing and monitoring functionality. The Adapter facilitates ease of use and helps to reduce board space and cost.
-
product
MTB Calibration Adapter
2450-CAL-30
The MTB Calibration Adapter (Catalog No. 2450-CAL-30)is a socket adapter that’s designed to bring phase A, B, and C current and potentials of a TESCO Multi-Position Test Board to an external RD-30 reference standard for calibration of the Test Board.
-
product
DVB-T SFN Adapter
MIPDVB
MIPDVB for HDc is ENENSYS’ SFN adapter module for DVB-T that inserts synchronization data to enable Single Frequency Network broadcasting.Running at the head-end after DVB multiplexer, the MIPDVB runs in the HDc chassis to embed up to 6x MIPDVB modules in 1U so that the same chassis can output up to 6 TS with MIP packets over ASI or IP.
-
product
Local DVB-T2 Adapter
T2 Edge DTH
T2Edge DTH is ENENSYS local DVB-T2 adapter of the OneBeam DVB-T2 solution. Running on the transmission site prior to the DVB-T2 transmitter, the T2Edge DTH aims at receiving a DTH stream to build a new DVB-T2 multiplex. It selects the services from the DTH stream and generates a T2-MI stream. The T2EdgeDTH performs an advanced PSI/SI processing to update PSI/SI information related to the filtered services.
-
product
Current Clamp Adapter
PeakTech Prüf- und Messtechnik GmbH
It uses a pair of jaw which allow clamping around an electrical conductor to measure the current in a conductor without the need to make physical contact unlike a normal multimeter.