- Pickering Interfaces Inc.
product
PXI Breadboard Module, 2-Slot, No Connector
40-220A-102
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
Mixed Signal Battery Test System
The Mixed-Signal Battery-Test System is an automated test platform designed to meet today’s advanced battery test requirements. The platform is ideal for testing a range of battery cells and packs, and can be used in applications such as research and design, quality control, and end-of-line manufacturing. Its distributed architecture provides a scalable solution with configurable system components to accommodate specific applications.
-
product
SoC Test System
V93000 SoC / Smart Scale
Advantest’s V93000 Smart Scale generation incorporates innovative per-pin testing capabilities. Each pin runs it own sequencer program for maximum flexibility and performance, for example in multisite applications. Full test processor control ensures time synchronization between all card types, like digital, Power, RF, mixed signal and so on. The user benefits are reduced test time, best repeatability and simplified program creation. The system design makes it easy to extend your configuration with new modules and instrumentation, as your test needs change.
-
product
Engineering Support Platform
ESP
ESP, or Engineering Support Platform, is a low cost, powerful and versatile platform for the development, deployment and support of FPGA Applications. ESP is powered by DSX core, ARC’s core element for the development and deployment of digital and mixed signal systems. The standard system contains 2 custom FPGA system, often configured in combination where one acts as the application firmware, and the other is used for test. But the system is expandable and configurable in any combination to sol...show more -
product
Mixed signal LSI test system
Multi-pin type model is now launched in WL27 Logic/Power mixed LSI test system.This system is suitable for multi-site test in A/D mixed device such as automotive・motor driver IC. It’s a high throughput and cost performance mixed signal LSI test system.
-
product
Mixed Signal Test Systems
MTS1000i
The MTS-1000i is lowest cost platform available in the MTS series of ATE. It has a reduced platform size compared to the MTS-2010i & MTS-1020i, reduced power supplies, and 4 slots. It is mainly intended for single site testing. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
product
GoldenGate RFIC Simulation Software
GoldenGate RFIC Simulation and Analysis Software is an advanced simulation and analysis solution for integrated mixed signal RFIC designs that is fully integrated into the Cadence Analog Design Environment (ADE). GoldenGate is part of Keysight's RFIC simulation, analysis and verification solution that also includes Momentum for 3-D planar electromagnetic simulation, SystemVue & Ptolemy wireless test benches for system-level verification, and the Advanced Design System (ADS) Data Display for advanced data analysis. This suite links the RF system, subsystem, and component-level design and analysis as part of a unique and comprehensive RFIC design flow.
-
product
JTAG Functional Test
JFT
JFT comprises a series of software modules that support boundary-scan test and programming activities under Python, National Instruments LabVIEW and Microsoft .NET framework. Using JFT users can create JTAG/boundary-scan test application scripts, VIs or programs for PCB assemblies and systems that control individual driver/sensor pins, groups of pins declared as variables or register bits. These applications are typically used to test logic devices or mixed signal clusters and can also be trans...show more -
product
A Popular Combination Of Flex 10 And Flex 20 In A Compact Footprint
Flex 30 ATE
A combination of both the Flex 10 and 20 system, the Flex 30 is floor mounted system that maintains a small footprint whilst offering that useful additional space. Generally it is fitted with either the G12 or G12X VPC interface allowing a large number of mixed signal connections to be routed to the test fixture.
-
product
Mixed Signal Test Systems
MTS2010i
The MTS-2010i are a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process.
-
product
Build to Print
In today’s fast paced manufacturing environment, where time to market and cost competitiveness is key, having a manufacturing partner like ARC can be a valuable resource for your company. ARC has a build-to-print manufacturing capability with our unique ‘engineer-to-print’ philosophy to make sure precision manufacturing and final build accuracy is top priority for your module level or system level builds. ARC can support up to several hundred module level assemblies (CCA subassemblies, cabling, ...show more -
product
Software
Digilent’s proprietary software solutions enable you to communicate with our system boards and a wide assortment of logic devices and use our available analog and digital test & measurement instruments. Refined by customer feedback for years, these powerful and FREE software applications allow you to fully customize your project, from creating and modifying designs for your system board to custom scripting of instruments for capturing, recording, analyzing, and generating mixed signal and mixed domain waveforms.
-
product
Mixed Signal Test Systems
MTS1020i
The MTS-1020i is a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
product
MEMS Device-Oriented Testers
Are your test requirements oriented to defined families of devices, with common characteristics? You do not need to purchase an expensive, general-purpose mixed signal tester: You can rely on SPEA DOT 100, a system designed to answer the test requirements of MEMS and other low-pin-count devices at an incredibly low cost.The DOT 100 is based on a revolutionary per-device architecture: each device under test has a dedicated CPU managing the entire test process, while each card hosts all the resources for the parallel test of 3 devices, in the size of a postcard.
-
product
AMIDA 5000 Tester
AMIDA 5000 is a high-end performance test system, combining analog, mixed-signal and logic with the latest test solutions. High pin count - as many as 512 smart multi-function pinframes and 128 sites. Ability to provide cost-optimized test solutions for a variety of consumer components in power management and mobile device components. This system has a higher number of parallel tests and a higher level of capability. This series of test systems provides a powerful test combination with high-spee...show more -
product
Photonics Wafer Probing Test System
58635
The advancement of the photonics device technology continues to enable broader and more demanding applications in the industry.
-
product
Laser Diode Burn-in Reliability Test System
58604
The Chroma 58604 is a high density, multi-function, and temperature controlled module for laser diode burn-in and lifetime tests. Each module has up to 256 SMU channels which can source current and measure voltage in various control modes as described below.
-
product
Laser Diode Reliability Burn-In / Life-Test System
58602
Chroma 58602 is a high density, precision multi source measurement Unit (SMU) module with temperature control and exchangeable interface developed for burn-in, reliability and life test of optoelectronic components including laser diodes, VCSELs, VCSEL Arrays, silicon Photonics, photo-diodes and other similar components.
-
product
Regenerative Battery Pack Test System
17040
Conforms to international standards for battery testing: IEC, ISO, UL, and GB/T, etc.Regenerative battery energy discharge (Eff. >90%, PF >0.95, I_THD <5%)Multiple voltage and current ranges for auto ranging function to provide optimum resolutionHigh accuracy current/voltage measurement (0.05%FS/0.02%FS)2ms current slew rate (-90% ~ 90%)Dynamic (current/power) driving profile simulation tests for NEDC, FUDS, HPPCTest channel parallel functionTest data analysis functionData recovery prot...show more -
product
Regenerative Battery Pack Test System
17020E
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
product
VLSI Test Systems
50/100 MHz clock rate50/100 Mbps data rate1024 I/O pins (Max :1280 I/O pins)Up to 1024 sites Parallel testing32/64 M pattern memoryVarious VI sourceFlexible HW-architecture (Interchangeable I/O, VI, ADDA,)Real parallel trim/match functionTime & frequency measurement unit (TFMU)High-speed time measurement unit (HSTMU)AD/DA test optionSCAN test option (max 1G M/chain)ALPG test option for embedded memorySTDF tools supportTest program/pattern converter(J750, D10, V50, E320, SC312, V7, TRI-6020, ITS9K)User friendly windows 7 environmentCRAFT C/C++ programming languageSW (Software) same as 3380P & 3360P
-
product
Photonics Module Test System
58625
Chroma 58625 provides characterization testing for 3D sensing illumination devices. various test modules are combined for validation testing under precise temperature control.
-
product
CPE Design Verification System
Jupiter 310
Jupiter is the industry standard for automated DOCSIS physical (PHY) layer testing. It provides the most comprehensive test coverage and accurate results on the market for DOCSIS 3.1 devices.
-
product
In-Circuit Test Systems For Sale
Forwessun offers a comprehensive range of global services for a variety of Test Systems. We provide refurbished systems that have undergone rigorous testing, giving you reliable performance at a fraction of the cost of new equipment. Whether you’re looking for a long-term solution to enhance your testing capabilities or a temporary setup to meet increased production demands, we have flexible options to suit your needs. - HP3070- Agilent - Keysight- GenRad- Teradyne Our bespoke rental agreements ...show more -
product
Custom Test System Solutions
No time to think about test? One-size-fits-all testers not ideal? Existing solution no longer fits your needs? Then count on integrated test solutions from Astronics. We’ll assist you with your test strategy and your test system, setting you on the path to market at a pace and ROI that ensures your program success.
-
product
Communication Test System
CTS-2700
The CTS-2700 is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The field-upgradeable, software-defined architecture features easy-to-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets can be created easily using the included TestEZ® software suite.
-
product
Regenerative Battery Pack Test System
17040E
High-power testing equipment up to 1,700V/ 4800A/ 1.2MW Multiple safety protections for personnel safety risk management and control of battery testing Flexible Integration for automated battery verification solutions
-
product
Radio Frequency, Communications, & Navigation Test Systems
Reduce testing time and costs with the Astronics radio test sets for use in military, avionics, and civil security industries.Available in commercial and military grades, these integrated test systems make it easy to develop test program sets and leverage them securely and instantly across all deployed testers at the factory, depot, and operational levels.
-
product
Communications Test System for Frontline Diagnostics
ATS3000P
The ATS3000P is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000P also includes the sophisticated IF and baseband I/Q DigitalSignal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easyto-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets are available for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
product
Advanced SoC Test System
3680
The Chroma 3680 is an advanced SoC test system with data rate up to 1Gbps. The Chroma 3680 is capable of conducting parallel tests on multiple chips to meet the digital and analog IC testing requirements, with applications including MCU, digital audio, digital TV, set-top box, DSP, network processor, field programmable gate array (FPGA) and consumer electronics.
-
product
Configurable Functional Test System
ATS-5000
Maximize the uptime of your most critical electronics with the ATS-5000 Functional Test System from Astronics Test Systems. Deployed globally for more than 20 years, the newest version of this tester provides a configurable, affordable solution that delivers just enough test.
