Filter Results By:
Products
Applications
Manufacturers
-
product
Climate Chamber
ICH
Its excellent temperature and humidity homogeneity positions the climate chamber ICH in the international top league of stability test chambers. Thermal transfer to the interior whether heat or cold is guaranteed through a large-area air jacket on four sides. Thanks to its hermetically sealed interior, the climate chamber ICH does not consume any water once the setpoints have been reached, provided that the door is not opened. Two high-grade platinum temperature sensors with mutual monitoring guarantee interruption-free long-term operation even if one sensor should fail.
-
product
Compact Temperature Chamber
FB1.5V-UHC Series
Based on the proven Bemco FB1.5V Compact Temperature Chamber, the FB1.5V-UHC offers spectacular temperature change rates in excess of 75 C per minute. With an extremely compact footprint these chambers cost about 1/3 of the amount of a typical 2-zone thermal shock chamber such as a Bemco FS2V.
-
product
Double-deck High and Low Temperature Environmental Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Double-deck High and Low Temperature chamber was designed to test battery cell combined with charge and discharge equipment, and also available to thermal test for small products and components.
-
product
External Pyrometric Camera for Combustion Thermal Monitoring
PYROSCAN-U
Pyroscan-U is specifically designed to perform thermal monitoring and mapping of any object inside a kiln, furnace, boiler or reactor, while looking at the area of interest through a standard window, from outside the combustion chamber. This megapixel pyrometric camera captures both visible and infrared HDR (High Dynamic Range) images of the burning zone.
-
product
HASS Chamber
Typhoon 8.0
The Typhoon 8.0 doubles the width of our popular Typhoon 4.0 chamber. The thermal system in the Typhoon series has been carefully engineered to have superior thermal efficiency.
-
product
High and Low Temperature Thermal Shock Chamber
HLST-500D
The specimen is placed in test chamber specimen which cannot be placed in high temperature chamber or low temperature chamber. High temperature chamber pre-heats the air and low temperature air chamber pre-cools the air. When doing the test of temperature changing from high to low, the low temperature chamber will blow the pre-cooled air to the test chamber. Then, the air in test chamber will reach your target temperature in several minutes (“recover time”). When doing the test of temperature changing from low to high, the high temperature chamber will blow the pre-heated air to the test chamber. Then the air in test chamber will reach your target temperature within the recover time.
-
product
Liquid Thermal Shock Baths
TSB Series
CSZ's Liquid thermal shock chambers consist of separately controlled hot and cold baths. Product is submersed in fluid and thermally stressed between the hot and cold baths, resulting in immediate product temperature changes. CSZ uses perfluorinated fluid that does not coat the product or conduct electricity for use in both the hot and cold baths to eliminate cross contamination and reduce evaporation losses.
-
product
Liquid-To-Liquid Thermal Shock Chambers
TSB Series
Purchasing a liquid thermal shock chamber needs close consideration of the long term operating costs. The specialized liquids used can easily evaporate, causing the loss of thousands of dollars of fluid per year, if not properly contained. ESPEC has led the industry in developing a sophisticated test chamber with multiple mechanisms to significantly reduce fluid usage. The new TSB-51 loses just 1.4 grams per test cycle, or less than a liter per 1,000 cycle test.
-
product
Rotary Thermal Shock Chambers
TS Series
A Bemco exclusive product, the TS Series of Turboshock Rotary Thermal Shock Chambers feature an electrically driven, 180 degree reversing, rotating wall located between two chambers, one hot and one cold. Two loads can be handled simultaneously. Front loading and rear access doors allow full entry to each zone.
-
product
Temperature shock test chambers test
TSS series
The operating principle of Schocktestprfschrank based of two superposed test rooms (top hot chamber, cold chamber below), between which a car with the test specimens is moved up and down by the large thermal shock test equipment may be subjected
-
product
Thermal Abuse Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Thermal abuse test chamber is suitable for standard IEC 62133-2017, UL 1642 and GB 31241-2014.
-
product
Thermal Abuse Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Thermal abuse test chamber protect for short circuit caused by incorrect operation of the operator and battery electrode, battery positive and negative connection, etc
-
product
Thermal Profiler
KIC K2
The latest-generation mobile-friendly profiling technologyThe KIC K2 Thermal Profiler features a compact and robust design that allows it to fit through the tight, heated chambers of lead-free reflow ovens. A plug-and-play hardware and graphical user interface makes profiling both quick and easy. The profile data measured by the K2 can now be viewed on either a PC or on a mobile device using the Profile Viewer App.
-
product
Thermal Shock Chamber
Wewon Environmental Chambers Co, Ltd.
Makes it possible to quickly and autonomously transfer test items back and forth repeatedly between a hot and cold environment.
-
product
Thermal Shock Chambers
Weiss Technik Thermal Shock chambers are designed to give quick transitions between a HOT and COLD temperature zones. Available in vertical, horizontal and liquid models. Thermal stock chambers are used in all industries including Automotive, Electronics, Aerospace, and others to help find product defects in electronic components and product assemblies. Thermal shock is important with MIL -STD 883 test standard.
-
product
Thermal Shock Test Chambers
How well does your product stand up to the shock of extreme thermal temperature changes? Tenney Environmental's thermal shock test chambers take products from 200°C to -65°C in just seconds.
-
product
(two/three-zone) Thermal Shock Chambers
TSA Series
Traditional three zone thermal shock chambers can be quite large, as three separate chambers are used. The TSA series has just one chamber, substantially reducing its size. Instead, it circulates cold, hot, or ambient air as needed. The conditioned air can be pre-cooled or pre-heated beyond the setpoint, allowing quicker recovery of the desired condition after transfer.
-
product
Integrated Thermal Control System
The Vektrex Integrated Thermal Control System (ITCS) uses proprietary water-based thermal control to maintain consistent LED and laser device temperatures during high power testing applications. LED/VCSEL manufacturers and third-party test facilities standardize on ITCS chambers for their testing needs.
-
product
Wafer Bonder
AML
Wafer bonding has found many applications in the field of MST, MEMS and micro engineering. These include the fabrication of pressure sensors, accelerometers, micro-pumps and other fluid handling devices. The process is also used for first-order packaging of silicon microstructures to isolate package-induced stresses. The OAI AML Wafer Bonder facilitates both the alignment and bonding to be performed in-situ, in a high vacuum chamber. For anodic bonding the wafers are loaded cold and heated in the process chamber. For high accuracy alignment the wafers are aligned and brought into contact only after the process temperature has been reached, thus avoiding differential thermal expansion effects which can compromise alignment. The AML Wafer Bonder is excellent for anodic bonding, silicon direct and thermal compression bonding applications. These features enable the bonder to be used with virtually any processing tool.
-
product
Environmental Test Chambers
Infinity Machine International Inc.
Environmental Test Chambers by Infinity Machine International Inc. - for applications such as hydrostatic test chamber for soles, thermal shock chambers, temperature and humidity test chambers, rainproof testers, UV light testing, and more.
-
product
Thermal Cycle Test
thermal test chamber from -40°C to +100°C with a programmable temperature controller and an accuracy of ±1°C. With a chamber size of 470 L x 420W x 460H mm (80L), it becomes a cost-effective testing unit for rechargeable batteries.
-
-
product
6 Slot VPX PCIe Gen2 Chassis
Desert Gecko
The 6 slot conduction cooled chassis can dissipate 120W in a non-moving air environment. The fin design and wall thickness was designed and analyzed with Flowmetrics software and designed for minimum delta T offset in an average thermal load application. The design was then verified in real life enviromental chamber experiments with a sealed chassis using our 3U heat simulator modules. Data available upon request.
-
product
Belt Starter Generator Test Systems
D&V has developed 12 V, 48 V and higher voltage BSG and ISG testing systems for performance, endurance and production testing, complete with thermal chambers, chillers and assembly lines.
-
product
2-Zone and 3-Zone Vertical Thermal Shock Chambers
FS
Originally developed for testing microelectronic devices for use in military and aerospace electronic systems, Bemco Vertical Thermal Shock Chambers are widely used for screening and quality evaluation of smaller electronic parts.
-
product
Altitude & Space Simulation Test Chambers
Weiss Technik’s vast experience with altitude, thermal vacuum, low temperature and space simulation test chambers can provide you with the right solution. We offer both pre-engineered and custom altitude chambers for ultra-low cooling, extended mbar, and extended temperature ranges that will meet your testing exact requirement.
-
product
2 Zone Thermal Shock Test Chamber
2-Zone Thermal Shock Testing Equipment with programmable electronics.
-
product
Combined Environmental Reliability Test System
VTC SERIES
HALT/HASS testing challenges the design, components, sub-assemblies and final assemblies of today's manufactured products. Stresses are applied through a number of conditions to set operational limits and ultimately precipitate failure in the HALT/HASS test environment. Rapid thermal change rate is one of the classic conditions that facilitate product stress.VTC Series chambers are equipped with an LN2 cooling system, with modulating valve and directed air flow to the product, provides the rapid thermal change rates required to achieve maximum product stress. Additionally, these rates are accomplished with smaller space requirements, lower audible noise, no water requirement, and lower maintenance costs than a typical refrigeration system.
-
product
Temperature Forcing System
Wewon Environmental Chambers Co, Ltd.
Wewon Technology specializes in the research, development, production and sales of laboratory testing equipment system services. Through more than ten years of accumulation in the field of equipment, the business of wewon Tech is mainly divided into three fields, namely optical communication, automobile and new energy industry.Specialized equipment from Wewon Environmental Chambers Co., Ltd. includes thermal stream instrument, environmental chambers, walk in chamber, salt fog test chamber, vibration testing machine, xenon lamp aging tester, ultraviolet weather testing equipment, tensile testing machine and various IP protection level test equipment. The system characteristic of Wewon Tech thermal stream temperature test system as below technical parameters mentioned.https://www.wewontech.com/temperature-forcing-system/
-
product
Environmental Simulation Testing
Innovative Testing Solutions, Inc.
We have multiple chamber capabilities of simulation most environmental conditions. Our chamber range in capacity from 1 ft3 to 64 ft3 volume. Specialty chambers include air-to-air thermal shock, inert gas injection oven, high/low pressure water spray and direct-injection LN2 chambers.
