Filter Results By:
Products
Applications
Manufacturers
-
product
Electronic Product Testers
Infinity Machine International Inc.
Electronic Product Testers by Infinity Machine International Inc. - for applications such as connectors insert and extract testing machine, touch screen torsion, abrupt pull tester for power wire and headphone cable, double station electronic product cable tester, cord flexing rotary bending fatigue tester, button click electronic product tester simulation, and more.
-
product
Charger Tester
G5.CT
The G5.CT series are unidirectional regenerative sinks. It was developed specifically for testing chargers and is suitable for use in laboratories and on test benches. The modular and finely graded G5.CT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The G5.CT series can simulate the electrical charging characteristics of a modern battery pack. This includes active voltage output and Ri realtime simulation.
-
product
HPx-310 Radar Signal Output Card
The HPx-310 Radar Signal Output card is a replacement for the HPx-300, form, fit, and function. It generates representative radar signals for system testing, simulation, training or radar video streaming. Under software control, the card generates radar video, trigger and azimuth signals similar to those generated by real radars.
-
product
ARINC825 Cards
AIM’s ARINC825 cards can work either with full functionality as an active CAN node for testing and simulating or in listening only mode for monitoring and recording purposes of Avionic CAN bus (ARINC825) applications on up to 4 electrically isolated CAN bus nodes concurrently. All nodes are in conformance with the ISO11898-1/-2 standard. They are accessible by software separately and can be used as 4 independent CAN bus nodes. An onboard IRIG-B time decoder allows users to accurately synchronize single or multiple modules to a common time source. All supported signals are available through front I/O and rear I/O interface. ARINC825 cards consist of FPGA based CAN interface controllers as well as a FPGA based 32-bit microcontroller core and a separate processor for IRIG-B synchronization with high resolution time stamping. All nodes are operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s with the intelligence to process scheduling of CAN frames in real time onboard to significantly off-load the host processor.For embedded applications the AMC825-4 PMC module is available in a conduction cooled version. Using AIM’s family of PCI, CPCI (3U and 6U) and VMEbus carrier cards for PMC our clients have off the shelf solutions in a broad range of card formats. ARINC825 (CAN bus) modules are delivered with an Application Programming Interface (API) and Driver Software compatible with Windows, Linux and VxWorks.An ARINC825 Resource Component is available for AIM’s PBA.pro™ databus test and analysis tool including Tx and Rx simulation capabilities, a Chronological Bus Monitor and support for decoding of payload data within CAN messages. This allows to implement a powerful ARINC825 (CAN bus) analyzer or a complete test system in conjunction with other AIM avionics databus interfaces and PBA.pro™ supported 3rd party hardware.
-
product
ARINC825 (CAN Bus) Test & Simulation Module for VME With 4, 6 Or 8 CAN Bus Nodes
AVC825-x
ARINC825 (CAN bus) Test & Simulation Module for VME with 4, 6 or 8 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AVC825-x VME card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
product
Altitude Chambers
EA-SERIES
A-Series Altitude Chambers offering the best of the unique and uncompromised features at competitive prices. Ideal for choosing your best suit for variable product sizes from the available range of standard sizes for meeting your test application for temperature, RH and low-pressure simulations of wide ranges. High performance & inherent reliability guaranteed for continuous testing of your products. These chambers can be easily movable on the wheels to convenient places and easy to maintain.
-
product
Altitude & Space Simulation Test Chambers
Weiss Technik’s vast experience with altitude, thermal vacuum, low temperature and space simulation test chambers can provide you with the right solution. We offer both pre-engineered and custom altitude chambers for ultra-low cooling, extended mbar, and extended temperature ranges that will meet your testing exact requirement.
-
product
Advanced GNSS Simulator
Skydel GSG-8
GSG-8 is the newest positioning, navigation, and timing test solution offered through Orolia’s GSG family of simulators. It was developed to deliver the highest standard of Global Navigation Satellite System (GNSS) signal testing and sensor simulation performance in an easy to use, upgradable and scalable platform.
-
product
Altitude Chambers
ESPEC can provide custom-built chambers for simultaneous testing of temperature and low-pressure altitude conditions. Two common applications are: Testing of avionics or other aerospace equipment to simulate actual conditions it might experience. Simulation of high-altitude conditions like might be found in mountainous regions.
-
product
Grid Simulator
PAS-F
The Intepro PAS-F Series is a broad line of programmable three phase output regenerative utility grid simulator products. With power levels ranging from 45kVA up to 1.6MVA, the series is capable of testing the largest of dispersed energy inverters. The PAS-F combines utility grid simulation with regenerative bi-directional AC source controlled power that is capable to both source and sink full current from the equipment under test (EUT).
-
product
Environmental Shock Simulation Machine For Drop Testing
# Simulates environmental handling threats small handheld products must survive.# Gauges your product?s ability to survive handling environments.# Controls key test variables: product orientation at impact; nature of the impact surface.# Maintains orientation to just prior to impact then releases for unrestrained impact.# llows user changeable impact surfaces to better simulate the handing environment.# Includes 4 ch short transient shock instrumentation system.
-
product
Environmental Simulation Testing
Innovative Testing Solutions, Inc.
We have multiple chamber capabilities of simulation most environmental conditions. Our chamber range in capacity from 1 ft3 to 64 ft3 volume. Specialty chambers include air-to-air thermal shock, inert gas injection oven, high/low pressure water spray and direct-injection LN2 chambers.
-
product
Dynamometers
When accuracy, reliability and performance matter look to the name that means dependability: A&D Technology. The comprehensive PerformanceLine includes a solution for all of the tasks of a modern and efficient test field, from durability, vehicle simulation, and high dynamic transient to high-speed e-motors. Choose from a variety of field-proven models from the PerformanceLine family with proven performance to meet your testing needs.
-
product
Emissions Dynamometers
MD-250-M
Mustang has developed a low-cost, simple to use, easy-to-install heavy duty chassis dynamometer that can be used to simulate real-world driving conditions in a safe, controlled environment and can also be used for “static” diesel smog testing for regulatory purposes. This model is used in Diesel Smog Programs in Nevada and Colorado when combined with an approved opacity meter. The MD-250-M is a compact dynamometer with industry proven design features including 10.7-inch rollers, heavy duty spherical pillow-block ball bearings, welded structural steel frame, 7.5 hp calibration motor, and an industry standard air-cooled, Eddy Current Power Absorption Unit (PAU) for road-load simulation. The MD-250-M is available in both right and left hand configurations to accommodate different facility designs.
-
product
Electrical
American Environments Co., Inc.
This testing includes the simulation of conditions or events that are associated with a device's input power leads (Mains).
-
product
Compliance Testing
American Environments Co., Inc.
The American Environments Company, Inc. (AECO) provides comprehensive compliance testing services. Our laboratory is fully equipped to provide Electromagnetic Testing, Environmental Simulation Testing and Dynamic Testing. Compliance requirements are related to the marketplace being serviced. AECO provides compliance services for: Products Exported to Europe, FCC, Telephone Network Equipment and Medical Devices.
-
product
Environmental Testing Services
INO offers a range of environmental testing services to help you perform prototype qualification and durability testing in the fieldtwo critical steps in the development of a reliable and profitable product. Our services can be used in a variety of settings, including quality control, land, sea, and air transportation simulations, accelerated aging simulations, resonance frequency searches, specifications and standards compliance testing and product qualification testing for standards such as MIL-STD, FOTP, and ESA.
-
product
Environmental Simulation Testing
What is environmental simulation testing? Simply put, simulated test environments are all about preparing products for real-world use. This is accomplished by gaining as much testing experience and performance data as early as possible during the products’ lifecycles. Simulated environmental testing usually involves creating artificial environments for test items to determine their expected resilience to their anticipated environments.
-
product
Date & Time Simulation Software
TimeShiftX
TimeShiftX is a date and time simulation software that lets you time travel software into the future or past for temporal testing all date and time sensitive functionality and code such as end of year/month, daylight savings, leap year, billing, rates, policies, etc. Perform time travel testing instantly, without any code changes, manual work, or server isolation
-
product
Electric Brake Force Meter With Dynamic Load Simulation And Circuit Testing
9107A
Innovative Products of America
The #9107 Electric Brake Force Meter with Dynamic Load Simulation and Circuit Testing (patents pending) is designed for use on 7-spade equipped vehicles. This new technology automatically recognizes the electronic signature of both Integrated (ITBC) and aftermarket Trailer Brake Controllers, simulates trailer load and displays real-time, brake-controller output gain and application time. It can quickly troubleshoot truck-side tow circuits, e.g., tail lights, turn signals, 12V+, reverse and ground condition and the 25 ft. cable allows for one-man, in-cab testing.
-
product
DDoS Testing
DDoS testing is a simulation of a DDoS attack performed under controlled conditions with real traffic. The goal of DDoS testing is to answer specific questions about the target environment.DDoS attacks are unique for many organizations in that they are relatively infrequent, but when they do occur they're often catastrophic. This catastrophic nature requires that a strategy be implemented to protect the organization, but a lack of real-world experience may limit the effectiveness of any solution. The infrequency of DDoS attacks often means that IT teams are developing solutions based on the "last attack" and waiting until the "next attack" to determine success. To address these challenges, NimbusDDOS created the first DDoS attack simulation platform. Our DDoS simulation services provide organizations the ability to proactively perform DDoS attack tests, using the same techniques used by real attackers. Unlike a real attack, a DDoS test is performed in a controlled manner and structured in a way to achieve the customer's objectives.
-
product
DC Source/Calibrators
Our DC Source/Calibrators are designed for a typical applications such as the design, check and calibration of high speed, high resolution A/D converters; design and certification of high speed data logging and process control systems; calibration of digital voltmeters and multimeters; as an “IMBEDDED STANDARD” and/or simulator; design, testing, simulation and certification of thermocouples, strain gages and transducer instrumentation.
-
product
Connector and Breakout Box
ES4640
The ES4640 Connector Box offers a standardized wiring and connectivity for HiL testing systems in the powertrain domain. Its front panel provides connectors for the ECU, CAN bus communication, on-board diagnostics, and LEDs for ignition and injectors. Its rear panel connects loads, failure simulation, and other components. Sample applications of the ES4640 are closed loop HiL systems for 8 cylinder gasoline and diesel engine ECUs.
-
product
C-SGN Emulator
The C-SGN Emulator combines the MME, SGW, and PGW functions, simulating the optimized EPC network required for CIoT. As part of the NetTest suite, the C-SGN Emulator creates an end-to-end lab environment for testing functions and features that characterize enhanced Machine Type Communication (eMTC) and Narrow Band Internet of Things (NB-IoT) implementations. In order to reduce complexity in the setup of a test environment, it also supports simulation of SMS Central Function (SMS-SC) and the Service Capability Exposure Functions (SCEF).
-
product
Electrodynamic shakers
EV232
Labtone Test Equipment Co., LTD
Labtone EV series of electromagnetic vibration testing system simulate the vibration environment under the laboratory condition, and test the impact strength as well as reliability of various vibration test applications. In the laboratory, with the aid of vibration testing system, simulations of reproduction of sinusoidal, random, resonant search and dwell, classical shock and road models, etc. can be achieved. It is essential for product quality assurance, new product research and development.
-
product
Environmental Simulation
Simulation of environment. PHOENIX TESTLAB's environmental simulation laboratory is accredited for environmental testing of a multitude of standards.
-
product
LTE eNodeB Testing
The DuoSIM and DuoSIM-Advanced are the most scalable eNodeB test systems in the industry. From basic functional testing to complex C-RAN environment simulation, the DuoSIM line of testers makes validation and development of network equipment faster, easier, and more cost effective.
-
product
(≤ 3.0GHz) DFB Light Source (ITU-T)
DFBL-0300
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai DFBL-0300 series is a set of high linearity DFB CW Light Source for modulation bandwidth <3GHz, mainly applied to optical accessory and fiber-optic communication equipment testing, modulation bandwidth <3GHz simulation, digital signal transmission R&D and application.
-
product
2-Axis Rate and Position Tables
When a device under test needs to be stimulated with simultaneous movements around two axes, then a product from the ACUTRONIC two-axis motion simulator range is the right choice. Due to their independent motion simulation in two axes they are very versatile: they are used as Inertial Guidance Test Systems (IGTS), for HardWare-In-the-Loop (HWIL) testing, for the test of optronic pointing devices, and many more applications.
-
product
Line Monitor
LE-170SA
LE-170SA is a compact hand-held size line monitor for CAN/LIN. It has a touch screen and can be control as for smartfones. It has 1 CAN channel and 1 LIN channel and it can monitor both CAN and LIN communication thus monitoring of the network which has both CAN and LIN is available. The monitor function can diplay the communication data in real-time while saving it. The simulation function can send/receive the test data instead of the original communication partner. The ID filtering and trigger function make your development/evaluation more efficient. It also can measure 4 external signals as degital signals or analog signals while monitoring the communication data.It is light (300g) and convenient for field testing. The line monitor is useful for not only development but also maintenance.
