Filter Results By:
Products
Applications
Manufacturers
-
product
CC-TLP Probe
CC-TLP-50-A1
High Power Pulse Instruments GmbH
*Capacitively coupled TLP probearm (CC-TLP) compatible with standard probing stations*18 GHz SMA connector*Tilt angle adjustment*Calibration gauge for needle height
-
product
Centesimal Thermometer Pt100
HD2107.1
Centesimal thermometer in the range ±199.99 °C, decimal outside this range, one input for Pt100 probes with SICRAM module measuring range -200 °C +650 °C.
-
product
Chair Probe
CP-1500
Stainless steel fabricatedTest chairs with a resistance meter like the Ohm-Stat RT-1000 Resistivity TesterIncludes banana plug to 4.0mm monaural plugMade in the USA
-
product
Chemitec Sensors And Analyzers To Monitor Oxidants In Water
Chemitec's S494 series of amperometric probes provide continuous, accurate monitoring of chlorine and other oxidants in clean water applications. A range of sensors assures accurate measurement of oxidation, with sensors optimized for Chlorine (total, organic or inorganic), Chlorine Dioxide, Ozone, Peracetic Acid, Hydrogen Peroxide, Bromine, or Chlorites.
-
product
CIE Colorimeter Probe
K-1
The Klein K-1 tri-stimulus CIE Colorimeter Probe is designed to be the best colorimeter in sensitivity, stability and speed. It attaches directly to a pc's serial com port (RS-232), and runs with the companion pc program. Whether a desktop or a laptop is used, the Klein measurement application is in control and many additional features are available.
-
product
Circuit Tester Set
TE6-0719
Hangzhou Tonny Electric & Tools Co., Ltd.
*Needle point probes*Continuity tester requires one AAA battery, battery not included
-
product
Clamp Meter
ST-3347W
Standard Instruments Co., LTD.
This clamp meter provides accurate AC, AC/DC current and voltage readings regardless of the waveforms. This meter can use in most industrial and commercial applications where non-linear loads distort the current or voltage waveform. Reliable operation. Features accessories such as test leads, carrying case and temperature probe.
-
product
Clamp Meters
Basic functions:AC current: 40/400/1000ADC current: 40/400/1000AAC voltage: 4/40/400/750VDC voltage: 400mV/4/40/400/1000VResistor: 400/4/40/400K/4/40MTemperature: -20 to +750°CFrequency: 10/100/1000Hz/10/100kHz/10MHzDuty cycle: 0.1 to 99.9%Capacitance: 5nF/50nF/500nF/5μF/50μF/200μFSpecial functions:Auto rangingNCVDiodeContinuity buzzerLow battery displayData holdRelative data holdAuto/manual range shiftZeroAuto power-offOverload protectionSampling frequency: 3 times/sMaximum display: 3999Maximum open distance of clamp mouth: 55mmGeneral characteristics:Color: iron gray and orangeNet weight: approximately 274gLCD size: 46 x 32mmSize: 245 x 90 x 33mmPower: 1 x 9V and 6F22Packing content:CartonHandheld bagEnglish manualTesting leadBatteryTemperature probe
-
product
Clamp Meters
Is an electrical test tool that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage.
-
product
Clamp Meters
Shenzhen UYIGAO Electronic Technology Co., Ltd
Combine meter and current probe into integrated instrument.
-
product
CLAMP ON CTS
P50
Beijing GFUVE Electronics Co.,Ltd.
mv AC clamp on current probe has 1mV voltage or 1mA current output, can measure cable and bus bar, max current is 1000A， high precision, can be used to monitor power quality. Perfect material permalloy core.
-
product
Clamp On Meters
Triplett Test Equipment & Tools
1000A True RMS AC/DC clamp-on meter with a backlit LCD display. It offers a large variety of measurement features including AC/DC Current, AC/DC Voltage, Resistance, Temperature, Capacitance, Continuity, Diode Test and NCV Detector. The rubberized overmolded housing provides impact and drop resistance in a sleek ergonomic design, and the user-friendly Auto Power Off feature helps maximizes battery life. With a CAT III 600V design, it provides superior resistance to damage from transient overvoltages in any demanding industrial setting. The Model 9325 is suited for a variety of industrial and residential applications such as security, electrical, HVAC installations and more. Includes test leads, Type K Temperature probe, 9V battery, and case.
-
product
Clamp-On Multimeter Series
An electrical test tool that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage.
-
product
CMM Retrofits
Eventually, measurement software, probe systems and controller electronics become outdated by newer, faster, better systems. Our range of standard retrofits and upgrade kits will inject new life into your measuring machine.
-
product
CO2 Carbon Dioxide Probe
HD320B2
The probe measures the carbon dioxide concentration in air. It’s indicated for checking and monitoring the indoor air quality. Typical applications are the check of the air quality in all the buildings where there is a crowd of people (schools, hospitals, auditoria, canteens, etc.), in the working places to optimize the comfort. CO2 measurement is obtained with an infrared special sensor (NDIR technology: Non-Dispersive Infrared Technology) that, thanks to the use of a double filter and a special measurement technique, warranties precise, stable and long-term measurements. The air to check is spread inside the measurement chamber through the protection membrane placed at the top of the probe.
-
product
CO2 Concentration Transmitter
T5241
CO2 concentration transmitter with 0-10V output is built in a durable watertight case. Output range is user adjustable. Large dual line LCD is an advantage. Display is possible to switch off. The device is supplied with CO2 probe with 1m cable. Cable lengths 2, 4 or 10 meters available optionally.
-
product
CO2 Concentration Transmitter
H5421
The device is supplied with CO2 probe with 1m cable. Cable lengths 2, 4 or 10 meters available optionally.
-
product
CO2 Concentration Transmitter
T5441
The device is supplied with CO2 probe with 1m cable. Cable lengths 2, 4 or 10 meters available optionally.
-
product
CO2 Concentration Transmitter
H5321
The device is supplied with CO2 probe with 1m cable. Cable lengths 2, 4 or 10 meters available optionally.
-
product
CO2 Concentration Transmitter
H5021
The device is supplied with CO2 probe with 1m cable. Cable lengths 2, 4 or 10 meters available optionally.
-
product
CO2 Concentration Transmitter
T5141
CO2 concentration transmitter with 4-20mA output is built in a durable watertight case. Output range is user adjustable. Large dual line LCD is an advantage. Display is possible to switch off. The device is supplied with CO2 probe with 1m cable. Cable lengths 2, 4 or 10 meters available optionally.
-
product
CO2 Concentration Transmitter
T5341
The device is supplied with CO2 probe with 1m cable. Cable lengths 2, 4 or 10 meters available optionally.
-
product
Coating Thickness Gauge
Dalian Taijia Technology Co.,Ltd
In built probe(s)● Operating principle: magnetic induction/eddy current (F/NF)● Measuring range:0-1250um/0-50mil● Resolution; 0.1/1● Accuracy: ±1-3%n or ±2.5um● Min. measuring area: 6mm● Min. sample thickness: 0.3mm● Battery indicator: low battery indicator● Metric/ imperial: convertible● Power supply: 4x1.5V AAA(UM-4)battery● Auto power off● Operating conditions:0-+45℃(32℉-104℉),≤90%RH● Dimensions: 126x65x27mm● Weight: 81g(not including battery)● Optional accessories:● other range 0-200um to 15000um● RS-232C cable & software: 1.USB adaptor for RS-232C 2.Bluetooth interface
-
product
Coating Thickness Gauge
Meter MEGA-CHECK -Basic
The new generation of MEGA-CHECK devices first used probes in which an own microcontroller, the analog sensor signals are digitized to the device outputs. This new technique is extremely trouble-free and even allows accurate and repeatable readings. The probe cable is both sides (control unit and probe) and therefore particularly service-friendly, as if a cable breaks, the device must not be returned, but only the cable is replaced. The units are equipped with a large, clear and illuminated graphic display. A variety of Fe, ferrous and dual
-
product
Coating Thickness Measurement Gauges
ElektroPhysik Dr. Steingroever GmbH & Co. KG
Handy, universally applicable coating thickness gauge in three versions: Integrated probes, cable probes and interchangeable internal and external probes.
-
-
product
CO Carbon Monoxide Probe
HD320A2
HD320A2 is a probe to be used with the HD32.1 Thermal Comfort data logger.
-
product
Combined Illumincance and Irradiance Probe
LP471P-A
Combined probe for measuring ILLUMINANCE (lux), with standard photopic response, and IRRADIANCE (μW/cm²) in the UVA spectral range (315…400 nm, with peak at 360 nm).
-
product
Combined Pressure and Temperature Transducers
Variohm offer some different styles of combined pressure and temperature transducers including the EPTT5100 which has an internal temperature sensor and the miniature EPTTE1400 which has an external temperature probe.
-
product
Combined Pressure and Temperature Transducers
We can offer some different styles of Combined Pressure and Temperature Transducers. The EPTT5100 combined pressure and temperature transducer has an internal temperature sensor. The miniature EPTTE1400 combined pressure and temperature transducer has an external temperature probe.
