Filter Results By:
Products
Applications
Manufacturers
DIP
Dual in-line Package
-
product
Digital Geological Data Collector
TECTRONIC
F. W. Breithaupt & Sohn GmbH & Co.KG
*Measurement and reading of azimuth of dip and angle of dip in one single operation (according to Clar method)*LCD display and memory for approx. 4.000 measurements*RS232 interface*Display indication 1° (360°, 400g, 6400– or 6300– selectable)*Many additional functions like measurement of magnetic field intensity)*Circular spirit level*Accessories upon request (Software, tripods, battery packs, …)
-
product
Din Rail Temperature Transmitters
Datexel manufacture a large range of Din Rail Temperature transmitters. From fully isolated, PC programmable temperature transmitters, Dip Switch Programmable are just some of the features available on the Datexel range of Temperature Transmitters. Some units are dual channel to help save space in a panel.
-
product
DIP Adaptor
48Pin .5mm QFP to 48Pin .6 Dip Adapter. Makes 48 pin QFP prototype circuits with a standard bread board easy.
-
product
DIP Header with Coined Contacts
Series 600
DIP Headers with Coined Contacts. Aries offers a full line of DIP headers, available with either coined or screw machine contacts. Consult Data Sheet No. 12035 for screw machine contacts. Snap-on, protective covers are available for all sizes shown below and accommodate .125 [3.18] to .750 [9.05] component heights. Consult Data Sheet No. 12033 for protective covers.
-
product
DIP Header with Screw Machine Contacts
Series 625
DIP Headers with Screw Machine Contacts. Aries offers a full line of DIP headers, available with either screw machine or coined contacts in a variety of styles. Consult Data Sheet No. 12032 for coined contacts.
-
product
DIP Jumpers
Series 100 thru 111
DIP Jumpers. Aries offers a wide array of DIP jumper configurations and wiring possibilities for all your programming needs. Protective covers are ultrasonically welded on and provide strain relief for cables. 10-color cable allows for easy identification and tracing.
-
product
DIP Program Header
Series 675
DIP Program Headers. Aries DIP programmable headers offer unusual versatility for programming within the header itself. They can be individually programmed using cutters or Aries programming tool, Part No. T-675, available separately, to remove the interconnecting sections. Consult Data Sheet No. 22002 for Aries programming tool.
-
product
DIP Test Clips
Low-profile fine-pitch chips, desnely populated boards, or vertical boards, Pomona test clips connect you with confidence.
-
product
Dip Tester
DS-02
Wide range of data can be obtained at one operation. Preheat temperature (temperature on underside of the board caused by preheaters.) Soldering temperature. Dip time.
-
product
DIP Tester
Model DS-10
Putting it a conveyor to flow through a solder bath to obtain information needed to manage it. The created temperature profile makes it possible to monitor the 50ms sampling temperature of the preheat and solder temperature sensors in addition to the conventional management items.
-
product
DIP-to-JEDEC TO Adaptor Socket
1109522 & 1109523
DIP to TO Adapter Sockets. 8 pin DIP IC socket on the top and a circular, 8 pin TO can male pin footprint on the bottom. ICs now available only in 8 pin DIPs can be readily mounted on boards having TO thru-hole footprints without having to redesign the board.
-
product
DIP-to-SOIC Adaptor
Series 354000
DIP to SOIC Adapters. Convenient, cost-effective means of converting DIP style packaging to SOIC PC board layouts.
-
product
DIP Vision Inspection Machine
Optima III
Landrex Technologies Co., Ltd.
DIP Vision Inspection Machine
-
product
Economy Model Vertisocket™
Series 800 and 822
Thrifty Model Vertisockets with Bifurcated Contacts. These low cost VertisocketsTM are recommended for high volume vertical display mounting applications. Very useful for connection of board-to-board jumpers and for DIP switches as well as LED devices.
-
product
Engine Control
StepGenerator4
*4-axis stepper motor control *Clock and direction signals *Speed up to 100,000 steps / s Positioning range +/- 2,147,483,647 steps *Simple ASCII commands via the serial interface *I2C adapter (master) for controlling external actuators / sensors *40-pin DIP package PCB (600mil / 19mm x 52mm).
-
product
FET DIP Meter
* 1.3 to 30 MHz coverage* Small 350 uA meter movement* Five coils covers HF HAM band*95 turn #36 AWG coil comes pre-assembled* Measures 5.5 x 2.5 x 1.1 inch* 9 volt battery operation
-
product
Handyscope TP450-250XM-W5
TP450-250XM-W5
The Handyscope TP450 is a power quality analyzer, connected via USB to the computer. The advanced measurement software delivered by default contains Quick Setups that allow to start mains power logging measurements without specialized instrument knowledge. With the 450 V input range, the Handyscope TP450 can be plugged directly in a (110 - 230 V) wall socket to measure the mains voltage. No additional attenuator is required. Logging mains voltage can be done at a high rate of 250 thousand measurements per second, with a resolution of 16 bit, which is equal to a 5½ digit voltmeter. The Handyscope TP450 is an accurate voltmeter, but one that performs 5000 measurements on each cycle of the mains voltage, while a standard voltmeter performs 3 measurements per second. Even with the very high measurement rate of the Handyscope TP450, the mains voltage can be measured continuously for weeks, and afterwards each period of the mains voltage can be analyzed thoroughly. Using this fast continuous measuring method, no voltage peak or dip is missed, even if it lasts just a msec. The maximum measuring duration of the mains voltage is only limited by the available hard disk space. Measuring one week takes approximately 0.69 GB disk space. During a measurement, also RMS value and frequency are logged. It is possible to measure various properties, like e.g. Minimum, Maximum, Peak to peak, Mean, Variance, Standard deviation.
-
product
Handyscope TP450-50XM-W5
TP450-50XM-W5
The Handyscope TP450 is a power quality analyzer, connected via USB to the computer. The advanced measurement software delivered by default contains Quick Setups that allow to start mains power logging measurements without specialized instrument knowledge. With the 450 V input range, the Handyscope TP450 can be plugged directly in a (110 - 230 V) wall socket to measure the mains voltage. No additional attenuator is required. Logging mains voltage can be done at a high rate of 250 thousand measurements per second, with a resolution of 16 bit, which is equal to a 5½ digit voltmeter. The Handyscope TP450 is an accurate voltmeter, but one that performs 5000 measurements on each cycle of the mains voltage, while a standard voltmeter performs 3 measurements per second. Even with the very high measurement rate of the Handyscope TP450, the mains voltage can be measured continuously for weeks, and afterwards each period of the mains voltage can be analyzed thoroughly. Using this fast continuous measuring method, no voltage peak or dip is missed, even if it lasts just a msec. The maximum measuring duration of the mains voltage is only limited by the available hard disk space. Measuring one week takes approximately 0.69 GB disk space. During a measurement, also RMS value and frequency are logged. It is possible to measure various properties, like e.g. Minimum, Maximum, Peak to peak, Mean, Variance, Standard deviation.
-
product
Header Covers
Series 650
Header Covers. Aries offers a complete line of DIP headers and covers useful for mounting components such as resistors, diodes, etc. Consult Data Sheet 12032 for mating DIP header information. Four cover heights provide mounting of 1/8? [3.18] high to 3/4? [19.05] high components.
-
product
High-Temperature SOIC DIP Adaptor
SERIES 35000-10-HT
High Temperature Lead Free SOIC DIP Adapters. A cost effective means of upgrading to SOIC...without changing your PCB layout. Available on .300 [7.62] centers. Consult Data Sheet No. 18011 for adapters on .400 [10.16], or .600 [15.24] centers.
-
product
I2C Adapter
RS485
*RS485 address adjustable via DIP switch*I2C frequency adjustable up to 400kHz*I2C level shifter, I2C level from 2V to 15V*Interrupt input for external events*Simple software interface (ASCII commands)
-
product
IP-Reflective Memory
Each IP-ReflectiveMemory can be used as a standard node or as the Master Node. Clearly labled "DIP Switches" are provided to make the selection of Master or Standard Node, and the Node Address. The Network is based on using LVDS signaling over Ethernet cabling. Nodes automatically come up for pass through operation.
-
product
ITA Terminal Blocks
YAVTB000
When wiring a test fixture, you often have a need to join three or more wires onto the same test point. This module solves this problem, adding test points for manual test probes and a 4 position DIP switch. Circuits 1 and 2 feature up to 5 poles in parallel to increase the space for power supply terminals.
-
product
Lasers FP/DFB-LDs For OTDR
C is a 1 650 nm Multiple Quantum Well (MQW) structured Distributed Feed-Back (DFB) pulsed laser diode DIP module with single mode fiber and internal thermoelectric cooler. It is designed for light sources of Optical Time Domain Reflectometer (OTDR).
-
product
Male/Female DIP Jumpers
Series 200 thru 216
Male/Femaie DIP Jumpers. Reliable, electronically tested solder connections. Protective covers are ultrasonically welded on and provide strain relief for cables. 10-color cable allows for easy identification and tracing.
-
product
MPO/MTP Multi-Fiber Interferometer
Anfkom International Co.,Limited
It is an automatic and non contact fiber endface interferometer for both multi fiber and single fiber connectors. It can measure the geometry parameters of multi fiber connector such as fiber height,core dip, X and Y angel, radius of curvature with white light and measure geometry parameters of single fiber connector with red light. The software can display the surface of the connector in 3D image for a very short time, it need only 8s to test 12-core MT connector. It is intelligent , efficient,stable and accurate and very helpful in improving the quality of the product.
-
product
New Basic Stratum Compass
GEKOM PRO
F. W. Breithaupt & Sohn GmbH & Co.KG
*Available in 11/2016*Measurement and reading of azimuth of dip and angle of dip in one single operation (according to Clar method)*Declination and inclination adjustable*Inner circle diameter 48mm with interval of graduation 2°*Reading by estimation 1°*Dip measurement range 270° graduated in 5°*Reading by estimation 1°*Circular spirit level*Waterproof one-piece housing*Declination adjustment without opening the housing
-
product
New Basic Stratum Compass with Clinometer
GEKOM N PRO
F. W. Breithaupt & Sohn GmbH & Co.KG
*Available in 11/2016*Measurement and reading of azimuth of dip and angle of dip in one single operation (according to Clar method)*Inclination adjustable*Inner circle diameter 48mm with interval of graduation 2°*Reading by estimation 1°*Dip measurement range 270° graduated in 5°*Reading by estimation 1°*Circular spirit level*Integrated clinometer ±90°*Mirror for observing needle during sighting process*Waterproof one-piece housing*Declination adjustment without opening the housing
-
product
Photocouplers/Optocouplers IC Output
The PS8xxx/PS9xxx series, a range of IC output type photocouplers (optocouplers), feature a high-speed response from 1Mbps to 15Mbps and a wide variety of DIP and SOP packages that can be surface mounted (SMD).
-
product
PLCC-to-DIP Adaptor
Series 652000/653000
PLCC to DIP Adapter. Converts PLCC packaged ICs to DIP footprints. Ideal for prototyping and testing/evaluation. Available with PLCC sockets or PLCC pads on top side. Consult factory for panelized form or for mounting of consigned ICs.
