Filter Results By:
Products
Applications
Manufacturers
-
product
Chrysler CCD Vehicle Bus Comms PC Card
SL100
The SL100 uses a standard 16450 UART with baud rate settings that makes it capable of communicating with a Chrysler CCD Vehicle bus. The SL100 uses a protected interface driver chip, as prescribed by the bus specification, to connect with vehicle peripherals in a robust and highly noise immune way. The card automatically configures to become another COM port by using the built-in O.S. drivers that are tried and tested and are optimized to work in the Windows environment.
-
product
Firmware for High-speed Communication
OP-FW12GA
OP-FW12GA is the firmware to increase the speed of monitoring test of bit synchronous communication (such as HDLC/SDLC/X.25, or CC-Link communication), SPI communication, Profibus-DP (field bus known for high-speed communication), UART (asynchronous communication, which is commonly used). By processing great part of monitoring processes by FPGA, it unfailingly captures communication data with time stamps of a microsecond rate. The interface supports RS-232C/RS-422/RS-485/TTL.
-
product
Flash Programmers
Easy fixture integration thanks to the compact size: 142x17,6x70mm, Independent ISP channels supporting several communication protocols (JTAG, SPI, I2C, BDM, UART, 8 digital I/O lines for each channel, coupled with dedicated ground return lines.
-
product
Four Port RS-232 Interface
PCI-COM232/4
Serial ports: 4Configured: Address and interrupt configured through PCI BIOS and supplied driversMax. baud rate: to 460.8 Kbps, software selectable per channel for 115.2, 230.4, or 460.8KbpsSerial modes: 5, 6, 7, or 8 data bits; odd, even or no parity; 0, 1 or 2 stop bitsUART: 16C550 standardInterrupt Status: Each UART interrupt status read from any UARTís Scratchpad RegisterConnector: 37 position D-type with fanout cable to 4 DB-9 or DB-25 male connectorsPower: +5V only
-
product
IP-OCTALPLUS232
IP-OCTALPLUS232 implements eight EIA-232 asynchronous serial ports, each with RXD, TXD, RTS, and CTS signals. In addition, two ports also have DCD, DTR, DSR, and RI signals. The serial ports are implemented with two Exar ST16C654 quad UARTs. Each channel has two 64-character FIFOs to allow longer interrupt servicing latencies.
-
product
IP-QuadUART
IP Module with quad UART capability. 128 byte FIFOs, 8 & 32 MHz operation, RS232 and RS422/RS485 interface, programmable terminations, 1.5MHz - 100 Hz.
-
product
IP-QuadUART-485
The IndustryPack compatible IP-QuadUART-485 design integrates a quad UART onto an IndustryPack module. The UART (16C854) features 128 byte FIFOs for RX and TX ports on each channel. The UART is supported by an advanced IP module interface implemented within a Xilinx FPGA.
-
product
Logic Analyzer & Digital Pattern Generator
ScanaQuad Series
ScanaQuad (SQ) is a series of high performance 4 channels logic analyzers and digital pattern generators. They are designed to be your best companion when working on serial protocols like UART, SPI, I2C, 1-Wire, USB, I2S, CAN, LIN, RS232, RS485, and more. With ScanaQuad Logic Analyzers, you can capture signals, you can play them back, and you can even build genuine test signals and generate them!
-
product
Low Profile PCI Express 1-Port
7106e
The 7106e low-profile PCI Express serial interface provides a single serial port configurable for RS-232, RS-422, RS-485 or RS-530. The ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allows the adapter to support the widest range of standard and non-standard baud rates exceeding 921.6 K bps. These features make the 7106e ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
product
Low Profile PCI Express 2-Port
7205ec
The 7205ec low-profile PCI Express serial interface provides two serial ports configurable for RS-232, RS-422 or RS-485. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7205ec ideal for data-intensive applications that require reliable, ultra-fast throughput rates.
-
product
Low Profile PCI Express 2-Port
7202ec
The 7202ec low-profile PCI Express serial interface provides two RS-232 serial ports. All modem control signals are implemented for maximum compatibility with a wide range of serial peripherals. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7202ec ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
product
Low Profile PCI Express 2-Port
7204ec
The 7204ec low-profile PCI Express serial interface provides two serial ports configurable for RS-422 or RS-485. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7204ec ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
product
Low Profile PCI Express 2-Port RS-232, RS-422, RS-485 Serial Interface
7205e
The 7205e low-profile PCI Express serial interface provides two serial ports configurable for RS-232, RS-422 or RS-485. Each serial port utilizes a 16C950 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the 14.7456 oscillator and UART’s flexible clock prescalar supports the widest range of standard and non-standard baud rates.
-
product
Low Profile PCI Express 4-Port
7402e
The 7402e low profile PCI Express serial interface provides four serial ports, each individually field-configurable for RS-422 or RS-485 communications. The board uses a 16C954 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data intensive applications. This high-performance UART includes 9-bit framing support and is register compatible with legacy 16550 software applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
product
Low Profile PCI Express 4-Port
7406e
The 7406e low profile PCI Express serial interface provides four RS-232 serial ports. For maximum compatibility with a wide range of peripherals, the board supports all standard RS-232 modem control signals. The serial ports utilize a 16C954 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
product
Low Profile PCI Express 8-Port
7802ec
The 7802ec low profile PCI Express serial interface provides eight serial ports, each individually field-configurable for RS-422 or RS-485 communications. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7802ec ideal for data-intensive applications that require reliable, ultra-fast throughput rates.
-
product
Low Profile PCI Express 8-Port
7803e
The 7803e low-profile PCI Express serial interface provides eight RS-232 serial ports. For maximum compatibility with a wide range of peripherals, the board supports all standard RS-232 modem control signals. The serial ports utilize 16C954 UARTs with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
product
Low Profile PCI Express 8-Port
7803ec
The 7803ec low-profile PCI Express serial interface provides eight RS-232 serial ports. All modem control signals are implemented for maximum compatibility with a wide range of serial peripherals. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates to 230.4 Kbps. These features make the 7803ec ideal for data-intensive applications that require reliable, fast throughput rates.
-
product
Microprocessors & Peripherals
Renesas offers MIL-STD-883-compliant microprocessors and a CMOS universal asynchronous receiver transmitter (UART) that are qualified to QML Class Q military standards.
-
product
Modules
Cimetrics offers several modules that can enable you to add BACnet capability to your products. Our modules, based on the Lantronix XPort, are elongated Ethernet RJ45 connectors that can be built into your product. Each module contains a microprocessor, memory, Ethernet MAC/PHY, serial (UART) interface, and firmware written by Cimetrics. The serial interface is typically used to communicate with another microprocessor in your product.
-
product
Multi-protocol USB Type-C Analyzer
Type-C Tracker
Protocol and Electrical Analysis Tool for Type-C Communications Standards. All-in-One: Concurrent and tightly synchronized capture of USB Power Delivery protocol, Type-C voltage tracking (Vconn, Vbus, SBU, and CC), USB 2.0, Thunderbolt 3 UART and DisplayPort auxiliary (AUX) signaling over the Type-C SBU lines, alternate (ALT) mode support for DisplayPort, HDMI, and Thunderbolt, and capture and decoding of Serial Wire Debug (SWD) protocol, UART, Serial Peripheral Interface (SPI) I2C vendor-specific protocols, and Type-C Port Controller Interface traffic over I2C.
-
product
PC/104-Plus And PCI-104 8-Port RS-232 Serial Communication
P104-COM232-8 and 104I-COM232-8
The P104-COM232-8 (PC/104-Plus) and 104I-COM232-8 (PCI-104) are PC/104-based eight channel RS-232 communication peripherals. Based on the XR17D158, the boards have eight enhanced 16550 UARTs, each with a set of modem signals (CTS, RTS, RI, DTR, DSR, CD). A 460Kb/s rate is guaranteed for all channels with up to 3K Ohm 1000pF loads. All interrupts may be monitored at a 32-bit status register. Each UART has both a 64 byte transmit and a 64 byte receive FIFO.
-
product
PCI Express 16-Port RS-232 Serial Interface
7161e
The 7161e provides sixteen RS-232 serial ports capable of data rates to 460.8K bps. Each RS-232 port implements all modem control signals for maximum compatibility with a wide range of peripherals. The board is PCI Express X1 compliant and utilizes 16C854 UARTs to provide 128-byte Tx/Rx FIFOs for maximum reliability in data intensive applications.
-
product
PCI Express 2-Port
7203e
The 7203e PCI Express serial interface provides two optically isolated serial ports, each individually configurable for RS-232, RS-422, or RS-485. Each serial port utilizes a 16C952 UART with 128-byte Tx/Rx FIFOs that enables data rates to 460.8K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is register compatible with legacy 16550 software applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high-speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
product
PCI Express 4-Port
7404e
The 7404e PCI Express serial interface provides four multifunction serial ports, each individually field-configurable for RS-232, RS-422, or RS-485. Each serial port utilizes a 16C954 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is register compatible with legacy 16550 software applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high-speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
product
PCI Express 8-Port
7804ec
The 7804ec PCI Express serial interface provides eight multifunction serial ports, each individually field-configurable for RS-232, RS-422, or RS-485. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates to 230.4 Kbps (RS-232) and exceeding 1 Mbps (RS-422/485).
-
product
PMC-BiSerial
Two fully independent and highly programmable RS-485 / RS-422 IO channels are provided by the PMC-BiSerial design. The channels are supported by two independent state-machines created within the Xilinx FPGA. The transmit and receive protocol can be the same or different. Manchester encoding and decoding, standard serial [UART], control, command, instrumentation, and custom protocols can be implemented.
-
product
PMC-BiSerial II-NG1
The PMC BiSerial-II NG1 is part of the PMC Module family of modular I/O components by Dynamic Engineering. The PMC BiSerial-II is capable of providing multiple serial protocols. The NG1 protocol implemented provides two full-duplex RS-422 UART interfaces with error detection, two half-duplex RS-485 custom "index" interfaces, external clock input, two clock outputs, and various discrete signal inputs and outputs, all using RS-485 transceivers
-
product
PMC-Serial
The PMC-Serial is capable of providing multiple serial protocols, both synchronous and asynchronous with a wide range of baud rates. The PMC-Serial has up to 8 UART channels, and two SCC channels. The protocol processors are complemented with a variety of IO which can be selected as a build option. RS-232, RS-485, RS-422, and RS-423 are supported. Two enhanced hysteresis MIL STD 188-114A receivers, and two open drain active low output drivers are also provided.
-
product
Qseven V1.2 SoM Evaluation Kit With I.MX287 454 MHz (Industrial) SoC, 128MB Memory, 4GB EMMC, Gigabit Ethernet, Audio, CAN And BSP
Q7M100-100-EVK
*Ultra low power consumption ARM9*High flexibility Qseven v1.2 compliant design*5 UART*2 CAN*24-bit TTL LCD*10/100 Mbps Ethernet*Linux 2.6.35
