- Pickering Interfaces Inc.
product
Diagnostic Test Tool
BIRST™ (Built-In Relay Self-Test)
Verification and diagnosis of complex switching operation in a test system has always been an issue. BIRST (Built-In-Relay-Self-Test) diagnostic test tool provides a quick and simple way of finding relay failures available on some of our LXI and PXI switch matrices.
-
product
S2 Spectra USB Sensors
ULP S2 SPECTRA USB
Universal LightProbe S2 Spectra USB Sensors test a wide range of LED intensities and any color in the visual spectrum, plus white, providing a linear response with a serial digital output via a PC. A standard USB Cable is provided to connect to a mini-type B five-pin USB connector, which is integrated into the S2 Spectra USB Sensor.Operating temperature range: 0oC to 70oCOutput Port: A standard mini-type B five-pin USB connector is integrated into the S2 Spectra USB Sensor,and a standard USB Cab...show more -
product
Constant Temperature Integrating Sphere
IS-*MT
According to requirement of IEC standards, the standard test temperature is 25℃, but high power lamps such as HID lamps and LED outdoor luminaires will produce a lot of heat during the test, thus the temperature inside the integrating sphere can not meet the requirements of IEC standards. Lisun Group designed the Constant Temperatured Integrating Sphere which allows the lamp was tested in a constant air temperature.
-
product
12V Automatic Battery and 12/24V Electrical System Analyzer
6044
• Easy-to-read LED voltmeter and ammeter• 500 amp safety clamps with “Flexi-Spring” and patented side terminal adapters• Separate 6 ft. high impedance test leads with alligator clips for tight spots• Cart / Printer can be purchased separately – Cart Model 6038C, Printer Model 6041• Automated testing of Batteries, Alternators, & Starters• Max/Min of Current and Voltage• Microprocessor based control board protected from reverse connections• Testing of 12V and 24V electrical systems• Test all ...show more -
product
Lan Cable Tester
Shanghai Beha Electronics Co., Ltd.
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.• The Lan cable tester can verify cable continuity, open,short circuit and miss-wired.• The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.• Auto and manual scan function.• Ground wire test.• Lock status function.• Buzzer sound warning for wire status.• Display: LED indication for wire status.
-
product
LED Test
Universal LightProbe Penta sensors are Optomistic Products' most popular LED test sensor, relied upon for their versatility in accommodating most LED test applications for color and intensity. The Penta Sensor provides analog voltage outputs, and features built-in color binning, eliminating the need to convert LED wavelength to visual color in the ATE software, and saving valuable processing time. For use with any of the Universal LightProbe Fiber-Optic Probes.
-
product
LED Tester Software
Lumeresoft
Evolusys Technologies Sdn. Bhd.
At the heart of the software design philosophy is the ease to create test recipe amidst the dynamic range of LED packages design & test requirements. Whether it is a single die LED, multiple die LEDs, Chip-On-Board (COB) substrate, etc. the same software can be used off-the-shelf without any special customization.
-
product
Loaded Spectrophotometer
DSCD-900
DSCD-900 is a highly performance spectrophotometer with test caliber upward. The instrument adopts the geometric conditions of D/8 lighting and observation of CIE recommendations, integration of the full band LED composite light source, double beam optical system, ETC every-time calibration technology, spectral reflectance standard deviation within 0.08, maximum of colorimetric values ΔE*ab is 0.03, to provide all the necessary color formula. It could be widely used for coating, printing, textile, meet plastic, food, medicine, automobile field to meet customers’ measurement requirement.
-
product
LANTRACKER
PH-100/120
The Lantracker is a network tester, pin-by-pin cable tester, and tone generator all in one. As a network tester, it detects whether a network is active or inactive and displays network speed (10/100/1000 Mbps) in either case. It also flashes the network hub or NIC’s port light corresponding to the cable it is connected to, to show the cable’s port number. As a cable tester, it performs loop-back or remote tests of network, data, voice, and coaxial cables, displaying the results on a pin-by-pin L...show more -
product
Probe Series
CAPELLA Series
MPI Photonics Automation is the industry leading provider of turnkey test solutions for the LED / Mini LED manufacturing industry. With more than 10,000 MPI probers installed worldwide, the CAPELLA series of probers have a proven track record of superior performance and reliability. The CAPELLA series probers support electrical and optical characterization of all LED product types (Vertical chip, Lateral chip, Flip-chip) from wafer to packaged die level. Whether you need a high-performance, cost-effective or specialty prober system, MPI PA has the most comprehensive range of LED wafer/chip probers to meet your exacting requirements.
-
product
LED View Angle Tester
360°rotate perspective die scanning.0.36° as the smallest test step unit.Conjunction with LED tester for electrical and optical parts test.Test data collection and perspective diagram drawing.Support 4 sets of probe socket (standard equipment with 2 sets of probe sockets)Clip structure. Easy for die positioning.
-
product
OST-500 Optical Radiation Test System
Hangzhou Everfine Photo-E-Info Co., LTD
OST-500 is an optical radiation safety test system with 200-3000 nm wavelength range, refer to IEC/EN 62471/CIE S009, IEC/TR 62778, GB7000.1-2015, GB/T 20145, IEC/EN 60598 Annex P., IEC/EN 60598 Annex P. IEC/EN 60432, IEC/EN 60335, GB/T34075-2017, GB/ T34034-2017 2009/125/EC and other relevant standards. The system is equipped with a precision automatic dual-axis turntable, which can automatically find and obtain the maximum radiation position, and automatically measure the photobiohazard value of various lamps and lamp systems (LED products, ultraviolet lamps, lighting sources and lamps, etc.) at the maximum radiation position, and carry out safety classification.
-
product
Relay Buddy PRO Test Kit
191
Relay Buddy is a quick go / no-go tester for the most common automotive relays. With the included adapters, Relay Buddy now tests 5 different relay types and also tests shielded relays. Relay Buddy provides you with an indication of the general health and functioning of the relay switch contacts and coil. It will check the control side of the relay by applying a signal to the relay coil while it checks for proper functioning of the relay contacts. Relay Buddy operates the relay several times during each test session as it watches for consistency in every cycle. Relay Buddy will fail the relay and light the RED LED if any one of the cycles proves unsuccessful during the test session.
-
product
Automated Digital Ground Continuity Tester
Educated Design & Development, Inc.
1 Button Testing - No setup required, just plug right in!Digital LED display reads out in OhmsAlso performs the Low Current Ground Continuity test, at the same time!Auto Test Time (1 sec. / 60 sec.)+ - No need to set a timer or clock watchCustom universal receptacle accepts both 120V and 240V plugs.Zero feature allows you to "zero-out" the test lead impedance.Meets UL, CSA, CE, EN, IEC, MIL and all other international safety agency requirements.
-
product
Voltage/Continuity Tester
VOT-52
Standard Electric Works Co., Ltd
● Voltage test: 12V to 1000V AC/DC (8 LEDs) with indication by buzzer.● Voltage range: 12V, 24V, 50V, 120V, 230V, 400V, 750V, 1000V.● Test leads positioned at 19mm apart.● Interchangeable probe tip for 2mm and 4mm.● Polarity test : LED +/-● Audible continuity test.● Phase rotation test : /● Self-test button to ensure proper function of the device prior to testing.● Waterproof design, protection class: IP65.● Phase / Neutral identification.● Rubberized double-molded housing.● ELCB / RCD trip test.● Flashlight function.● Safety standard : IEC/EN 61010-1 III 1000V IEC/EN 61010-1 IV 600V IEC/EN 61243-3 EN 61326-1
-
product
Economical LED Display for Remote Annunciator Applications
AN-3100D-LC
LED Illumination for long life, low power Laser Printed window Legends Compact Size Barrier, screw terminal connection Panel or 19" Rack Mounting 4 Windows Sizes: 3x3, 1.5x3, 1x3, 1.5x1.5 Selectable Window Colors: White, Red, Blue, Green Amber Built-in Test Pushbutton option
-
product
DataComm & LAN Testers
Tests & troubleshoots voice communication for open circuits, shorts, miswires, reversals, and split pairsSHIELD detection tests a cable’s shield integrityEasy to read fault display and high speed testingDebug mode for detailed fault identification resultsNetworking Cable Tester has auto sleep mode and power off switch to decrease power consumptionBattery low LED indicator
-
product
Non-Contact Voltage Detector
273 HP
Standard Electric Works Co., Ltd
● 2 ranges for selection : LOW 50V~1.5kV HIGH 1.5kV~132kV● There is no power consumption in off mode : 0uA● Nice mechanical slide switch for function selection : HIGH / OFF / LOW ● The power consumption in low voltage detection mode : Less than 20mA● The power consumption in high voltage detection mode : Less than 20mA● Bright LED and audible alarm sound when voltage is present.● Lightweight, robust and compact.● Efficient and easy to use● Users hav...show more -
product
Spectroradiometer
Designed to have a capability of producing any visible spectral distribution, mimicking various light sources in the visible region by feedback control of the radiant power emitted by individual LEDs. This LED test system will be used as a transfer standard for photometric, colorimetric and radiometric applications.
-
product
Measurement System For Testing & Binning Of Back-End LEDs
TP121-TH
The photometric specifications of LEDs must meet very high tolerance requirements regardless of whether they are to be used in general, automotive or other specialist lighting applications. This is often a problem since the manufacturing tolerances of LEDs can be higher than those permitted in the end-use applications. Also, LED binning by LED manufacturers in order to classify LEDs based on their tolerances is performed with flash mode testing using pulsed current flow. However, end-use applica...show more -
product
Voltage Testers
DUSPOL
BENNING Elektrotechnik und Elektronik GmbH
phase-sequence test (counter-clockwise / clockwise)single-pole phase test: " symbol (red LED)measuring point illuminationacoustic and optical continuity testfrequency measurement 1 1000 Hzvoltage indication 1 1000 V AC TRUE RMS / 1200 V DCresistance measurement and diode test with conducting-state voltage indicationlc display with background lightingsensor of non-contact cable break detectorload connection via large-scale push buttonsvibrating alert in the test handleshock-resistant housing with protection against dust and water jets (protection class IP 65) and rubberized test handleDIN EN 61243-3 (VDE 0682-401): 2015 standard
-
product
Lan Cable Tester
185 LCT
Standard Electric Works Co., Ltd
● Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable.● The LAN cable tester can verify cable continuity, open, short circuit and miss-wired.● The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.● Auto and manual scan functions.● Ground wire test. ● Lock status function.● Buzzer sound warning for wire status.● Display : LED indication for wire status.
-
product
LED Driver Online Tester
LEDLS-60/LEDLS-12
• The tester includes A Group Measuring Module and B Group Measuring Module. The A Group measuring module can test 6pcs LED Driver AC Parameters. The B Group measuring module can test 6pcs LED Driver AC, DC and AC/DC Parameters. • There are 12 windows to display the input and output parameters, it is good for comparing and analyses. • Quick test for all of the parameters in 0.1 seconds. • It can set up the testing parameters PASS/FAIL range, it will have Noise/Light warning if it is Fail. We also supply handle port (Extra cost) • Software communicate with PC (Extra cost)
-
product
Explosion Proof UV Inspection Light
he Labino MB Hercules Ex is an extremely durable product specifically developed for use in areas where the risk of an explosion is high. Offshore Oil Rigs, Refineries, Aerospace, and Defense often require explosion proof products to ensure safety for their inspection teams. The Midbeam Hercules Ex has successfully completed extremely tough tests, including tests for thermal conditioning, Impact Tests, Drop Tests and IP tests that led to the ATEX certification (Certificate: ITS17ATEX402144X). This unique product is suitable for use in extreme weather conditions varying from 104° Fahrenheit (+ 40° Celsius) to minus 4° Fahrenheit (- 20° Celsius).
-
product
Steam Aging Tester
Wewon Environmental Chambers Co, Ltd.
These steam aging chamber applied for the testing of sealing property for multi-layer circuit board, IC sealing package, LCD screen, LED, semi-conductor, magnetic materials, NdFeB, rare earths and magnet iron, in which the resistance to pressure and air tightness for above mentioned products can be tested out. ● Overall of the steam aging tester made of stainless steel SUS # 304HL, simple operation settings. Microcomputer digital LED control with time planning function , the maximum set 9,990 ...show more -
product
H.V. Proving Unit (DCV)
2713 PU
Standard Electric Works Co., Ltd
● Designed to proof: -Phasing sticks. -High voltage detectors (contact type only, not to be used with non contact proximity detectors.) -High voltage and voltage testers.● Battery operated.● Led indicates when power is “ON”.● Small and hand-held.● Quick connection with normal 4mm test leads.
-
product
Drop Weight Tear Tester
DWTT
Since the introduction of the Drop Weight Tear Tester - DWTT, materials have moved on. In particular, demands for high operating pressures of line-pipes and larger diameters have driven the development of higher strength steels. Forty years ago the work that led to the drop weight tear test was done on X52 steel (360MPa yield strength). Improvements in thermo-mechanical processing has yielded improvements of approximately 10,000psi per decade, to the point where the state of the art is now X100 steels, and the use of X120 steels is being considered.
-
product
S2 Penta High-Sensitivity Sensors
ULP S2 PCI/V HS
The Universal LightProbe S2 Penta High Sensitivity Sensor features the same popular built-in color binning as the regular S2 Penta Sensor, and is designed test extremely dim LEDs, providing an analog output for intensity, ranging from 0 to 4 volts, corresponding to the LED’s luminous intensity in millicandelas. Implemented in a unique and customizable 2-Part solution, the S2 Penta High Sensitivity Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced...show more -
product
Goniophotometer Test System For Led Lamp
1680A 1680B
Shenzhen Chuangxin Instruments Co., Ltd.
Design according to IEC61341,the test method of central luminous intensity and beam angle for reflecting light, this instrument can be used to test the cross section luminous intensity distribution curve, central luminous intensity and effective beam angle of LED assembled luminaries and LED lens system with diameter less than 180mm.
-
product
Mini Multi-Battery Tester
Mini-MBT
The ZTS Mini Multi-Battery Tester (Mini-MBT) provides a comprehensive means of testing the state of charge or state of power for more than 15 battery types. The mini-MBT’s microprocessor-based design makes battery testing simple - using a patented, high accuracy pulse load test. After a fully automatic test cycle, percentage of remaining battery capacity is indicated on the LED bar display.
-
product
GLP2 Luminaries/LED Tester
Safety, function, programming and controlling of LED Lighting from one device. Dramatically reduces set up and test times. Ease of use eliminates errors.
