Current Sensors
detect AC or DC electrical current.
See Also: Current Probes, SQUID, Voltage Sensors, Rogowski
- Valhalla Scientific Inc.
product
100-Amp Current Calibrator And AC/DC Transconductance Amplifier
2555A
World’s Leading Precision 100-Amp AC/DC Current Standard - For 30 years Valhalla Scientific’s design has proven rock-solid reliability in metrology labs worldwide. The 2555A is a calibration powerhouse with wide-ranging applications and unsurpassed quality.
-
product
Current Clamps and Sensors
Are designed for measuring leakage current diverted towards the earth. It enables the fault to be located or anticipated without disconnecting the equipment linked. It is specially designed to detect low fault currentson power circuits.
-
product
500A AC/DC Current Sensor
CT6904
Hioki pull-through AC/DC current sensors are best-in-class devices for use with power analyzers,, Memory HiCorders and high performance oscilloscopes. The CT6904 is a DC to 4 MHz/500A sensor, ideal for capturing current signals from switching power supplies, inverters, power conditioners, etc.
-
product
Device Current Waveform Analyzers
The dedicated Current Sensors measure from 100 pA level dynamic current up to 10 A with a maximum of 200 MHz bandwidth. The mainframe acquires the signal from the sensors by a maximum of 1 GSa/s sampling speed and 14-bit and 16-bit wide dynamic range. This combination allows you to measure quite wide range of dynamic current, for example, from standby/sleep state to active state, at a single measurement. In addition, the wide bandwidth and the high speed acquisition enable you to measure high speed pulse response even less than 100 ns previously very difficult with existing instruments.
-
product
Web Sensor
P2520
Converter Web Sensor P2520 is designed for the connection two sensors with current output into Ethernet network. The measuredcurrent (0-20mA or 4-20mA) can be converted to the physical quantity that is measured by the connected sensor. The converter isgalvanically isolated from the Ethernet communication lines, current inputs and power supply are not galvanically isolated.
-
product
PXI Load Resistor Module 40 Ohm to 295 Ohm
40-292-011
The 40-292 module is able to simulate the common short circuit and open circuit conditions that can be experienced in a system due to faulty wiring or sensors. The short circuit position is fully thermally protected and provides a short circuit current limit. The series open switch provides an automatic current limit through the resistor chain and is thermally protected.
-
product
PXI-6238, 8 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sourcing DO, Bank-Isolated, PXI Hybrid, Multifunction I/O
779624-01
8 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sourcing DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6238 is a bank-isolated DAQ device designed for current I/O. It offers analog I/O, digital input, sourcing digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 24 V signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurement...show more -
product
Monitoring Solar Panel Strings, DC 30A, Φ10mm
CTF-60-10DC
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Compact, Space-saving, Low Cost DC Current Sensors.・Split-core type, easy to apply to existing circuit.・Easy to use by unipolar +5V power supply.・High speed responsibility – less than 10μsec. 0 rated primary current.・Suitable for monitoring solar panel strings.
-
product
SparkFun PIR Breakout
1uA (EKMB1107112)
Passive Infrared (PIR) sensors are great for detecting motion in a small area around the sensor. The 1µA SparkFun EKMB1107112 PIR Breakout is a simple breakout equipped with an EKM-series PIR sensor from Panasonic®. The EKMB-series PIR sensors are optimized for small movements to offer motion-sensing options for battery powered applications due to the very low standby current consumption (1µA).
-
product
24 TTL Channels, Enhanced, Programmable I/O
TL2
Function module TL2 provides 24 channels of TTL/CMOS transceiver functionality as either inputs or outputs. The transistor-transistor logic (TTL) employs transmitters with multiple emitters in gates having more than one input. TTL offers high switching speed and relative immunity to noisy systems. CMOS sensors provide image sensing technology by converting light waves into signals that are small bursts of current. These waves can be light or other electromagnetic radiation.
-
product
NI-9219, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module
779781-02
100 S/s/channel, 4-Channel C Series Universal Analog Input Module - The NI‑9219 is designed for multipurpose testing. With the NI‑9219, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors, as well as make quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. Each channel is individually selectable, so you can perform a different measurement type on each channel.
-
product
Open Loop Hall Effect Current Sensors Transducers With Rectangle Windows
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a highgalvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current, DC pulse currents etc. The output of the transducer reflects thereal wave of the current carrying conductor.
-
product
sbRIO-9218, Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module
783362-02
Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module - The sbRIO‑9218 helps you perform multipurpose testing. With the sbRIO‑9218, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors. You also can use the sbRIO‑9218 to perform quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. You can individually select and perform a different measurement type on each channel. Additionally, the sbRIO‑9218 features 60 VDC analog input isolation. Non-enclosed modules are designed for OEM applications.
-
product
RS-232 to RS-422/RS-485 Converter
ND-6520
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS...show more -
product
Loop-Powered Transmitters and Drivers
4-20mA
Loop-Powered Transmitters convert the output from proximity probes, seismic sensors, into a 4-20mA DC current, which is proportional to the input being measured. The transmitter converts the displacement or vibration signal to DC voltage and/or current for a DCS or PLC system. They control a 4-20mA current loop for a specified vibration range (ex. 0-5 mils peak-to-peak). The transmitters have a two-wire hook-up, powered solely by the loop current and have a power supply range of 15 to 36 volts.
-
product
Condition Monitoring
Condition monitoring products help you keep your plant floor running productively by detecting potential equipment failures. We offer real-time protection modules, sensors, portable instruments, and surveillance software. Our XM® Series of intelligent I/O modules performs real-time processing of critical parameters used in assessing the current health and predicting the future health of industrial machinery. Apply our XM modules in standalone systems or with existing automation and control systems.
-
product
24 TTL Channels, Programmable I/O
TL1
Function module TL1 provides 24 channels of TTL/CMOS transceiver functionality as either inputs or outputs. The transistor-transistor logic (TTL) employs transmitters with multiple emitters in gates having more than one input. TTL offers high switching speed and relative immunity to noisy systems. CMOS sensors provide image sensing technology by converting light waves into signals that are small bursts of current. These waves can be light or other electromagnetic radiation.
-
product
Integrated Flight Controller
Kratos Defense & Security Solutions, Inc.
The Integrated Flight Controller (IFC) controls the entire flight functionality and maneuverability of the BQM-167 subsonic aerial target platform. The IFC accepts commands from a ground control system (such as GRDCS, SNTC, or TTCS), inputs current vehicle operating parameters from onboard sensors, and outputs control signals to the vehicle for flight control. The IFC supports multiple high performance maneuvers, such as barrel rolls, high G turns, and low altitude operation.
-
product
Eddy Current Sensor
eddyNCDT 3001
The eddyNCDT 3001 is a new, efficient eddy current sensor whose compact dimensions have to date only been reserved for inductive sensors and proximity sensors. The temperature-compensated design provides high stability even in fluctuating ambient temperatures. The eddyNCDT 3001 comes with integrated electronics, offering an outstanding price/performance ratio and easy operation. The eddyNCDT 3001 eddy current sensor is ideally suited to OEM integration and machine building applications. The sens...show more -
product
Electronic Multifunction Data Loggers
The DeltaTrak Electronic Data Logger is a portable, pocket sized electronic device powered by a 10-year lithium battery. It is designed for easy and reliable tracking of parameters such as temperature, relative humidity, electric current, pressure, process signals, and pulse signals. All data loggers have a built-in temperature sensor plus single or multiple external channels where different sensors can be attached for remote monitoring of a variety of parameters. The DeltaTrak Data Loggers inte...show more -
product
Isolation and Power Solutions
Silicon Labs' innovative digital isolation and power product portfolio includes CMOS digital isolators, isolated gate drivers, isolated current sensors, isolated system products and Power over Ethernet (PoE) families. These mixed-signal IC solutions leverage Silicon Labs' superior isolation and high voltage expertise to enhance power system performance, flexibility and reliability while reducing system size and cost. The entire isolation portfolio supports isolation voltages up to 5 kV.
-
product
Ammeter Recorder
Beijing GFUVE Electronics Co.,Ltd.
The accuracy, external current reject, and range of currents measured by the patented amp sensor substantially exceed the performance of the best clamp-on sensors.
-
product
RS-422/RS-485 Repeater
ND-6510
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS...show more -
product
Data Acquisition Systems & Data Loggers
Whether it’s in a vehicle, on a test stand or monitoring equipment and machinery - imc data acquisition systems are easy to operate and will help you become more productive and profitable. Our products are suited for work in mechanical and mechatronic applications. They handle up to 100 kHz per channel, are compatible with almost all signal sources and sensors, and can measure nearly all physical quantities such as pressure, force, speed, vibration, noise, temperature, voltage and current. The spectrum of imc data acquisition systems ranges from simple data acquisition via integrated real-time calculations, to the integration of models and complete automation of test stands.
-
product
Multifunction Calibrator 15 ppm Basic Accuracy
MC142
Multifunction calibrator MC142 is a precision voltage, current and power calibration source serving as a measurement standard in calibration laboratories and production lines; where verification of electrical measurement equipment & sensors is required. It can be used for calibration and adjustment of meters measuring voltage, current, power, resistance, capacitance and frequency. Internal harmonic and non-harmonic signals make it possible to test electrical performance of meters using sig...show more -
product
Monitoring Solar Panel Strings, DC 30A, Φ10mm
CTF-30-10DC
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Compact, Space-saving, Low Cost DC Current Sensors.・Split-core type, easy to apply to existing circuit.・Easy to use by unipolar +5V power supply.・High speed responsibility – less than 10μsec. 0 rated primary current.・Suitable for monitoring solar panel strings.
-
product
Integrated Current Sensors
FHS Series
*Standard package and small footprint*Cost effective*Standard SOIC 8 surface mount PCB
-
product
Current Sensors
Measurlogic offers an array of current sensors for every need, including split core, solid core and Rope current transformers (CTs); DC Shunts and Hall Effect Sensors. All of our electrical sensors are designed with an easy, un-intrusive installation in mind. With a low cost and high accuracy guarantee, we provide top of the line solutions for measurement and cost savings for residents and business owners alike.
-
product
Flow Sensors
Rugged and precise – flow measurement technology from SICKSICK provides innovative sensor solutions for flow measurement technology which combine flexible measuring methods and rugged equipment design with cost-efficient connection concepts to integrate higher-level systems. Whether you need to detect the current flow rate value using analog values or find the quantity using pulse detection – SICKs flow sensors are always reliable and safe and can work with a wide range of media under difficult process and ambient conditions.
-
product
Digital Test Switch
FT-14D
Test switch solution for digital switchgear using current and voltage sensors. With the FT-14D Digital FlexitestTM switches, a new era of protection relay testing can be performed more safely, quickly and easily. The FT-14D switch allows a customer to integrate current and voltage sensors within digital switchgear and protective relays and thereby enable the Industrial Internet of Things.
-
product
Current Input0 to 20mA
TGPR-0804
Current input data logger. A current input data logger that is housed in a robust, waterproof (IP68) rated case. The TGPR-0804 can be used to record the output from a number of industry standard 4-20mA sensors. Common applications include pressure and flow rate monitoring.
