Thermal Test
Designed to produce a temperature change in a device. The magnitude and rate of this change should induce a sufficient thermal stress fatigue to identify sources of potential failure without causing catastrophic failure of all components. (sigmasystems.com)
See Also: Thermal, Thermal Shock
- Pickering Interfaces Inc.
product
PXI 32 Channel I/O, Low Side Driver
40-413-002
A 32 channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only, a low side only (shown here)and a combined high and low side each capable of driving 2A loads. Each output is fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side voltage driving the high side voltage source is supplied from an external voltage source, permitting the module to drive high capacity loads without impacting the PXI chassis power supply.
-
product
Thermal Division Overview
MPI Thermal is a division of MPI Corporation. With over 60 years of combined thermal control system experience with our international engineering teams, this has brought about a comprehensive product portfolio of thermal air stream systems for today's manufacturer's environmental test chamber needs.
-
product
Cryogenic Millimeter-Wave / Microwave Test Fixtures and Calibration Kits
upj10
KEYCOM''s cryogenic millimeter-wave / microwave test fixtures and calibration kits are specifically optimized for testing the performance of patterns between the edges of printed boards(edge type) and circuit testing on the printed boards(probe type). They are also designed to minimize heat capacity by miniaturizing their dimensions so they cool off efficiently, and materials with low coefficient of linear thermal expansion such as invar are used for major parts where high dimensional stability is required. Their operating frequency ranges from DC to 110GHz.
-
product
EV Battery Pack Test Equipments
Guangdong Bell Experiment Equipment Co.,Ltd
All industrial battery tester from BELL lithium battery test chamber supplier meet the standards of GB31467.3, ECE-R100 and UL2580. The tests mainly simulating all the condition that driving an EV meet, including battery crush test, battery drop test, flammable test, temperature cycle test, short circuit test, thermal test, explosion test, and environmental test, etc.
-
product
Thermal Test Chip
Thermal Engineering Associates, Inc.
Thermal Test Chips (TTC) are used in many different Applications: Package Thermal Characterization, Heat Source Simulator, Temperature Reference Platform, Transient Analysis, System Thermal Management Design, Thermal Interface Material (TIM) Measurement & Characterization, Heat Sink Measurement & Characterization.
-
product
Glove Heat Insulation Tester
DRK6003B
Shandong Drick Instruments Co., Ltd.
Use a high-temperature object to directly touch the glove to simulate the temperature rise of a human hand in the glove within a certain period of time, and objectively test the relevant parameters of the glove's thermal insulation performance.
-
product
Dynamic Micro Ohm Meter
PRIME 600
It is the only micro ohm meter in the market that integrates both the contact resistance and the dynamic resistance measurement (DRM) for cost-efficient condition evaluation of contacts in SF6 and vacuum type circuit breakers; PRIME is a high current micro-ohmmeter that provides true pure DC with smart control up to 600 A, a wide measurement range with high power, dual ground testing process, thermal printer, touch display, pre-defined test modes and automatic reporting.
-
product
Test Contactor
cDragon
cDragon™ Test Contactor pin’s thermal design supports fast temperature control response and stabilization for repeatable at temperature testing of devices in a handler environment.The homogenous MEMS elastomer-free multi-beam pin delivers long life and high wear resistance. By design the cDragon’s pin decouples insertion motion from the test-interface-board side of the pin. This eliminates test-interface-board pad wear.
-
product
Measurement System For Testing & Binning Of Back-End LEDs
TP121-TH
The photometric specifications of LEDs must meet very high tolerance requirements regardless of whether they are to be used in general, automotive or other specialist lighting applications. This is often a problem since the manufacturing tolerances of LEDs can be higher than those permitted in the end-use applications. Also, LED binning by LED manufacturers in order to classify LEDs based on their tolerances is performed with flash mode testing using pulsed current flow. However, end-use applica...show more -
product
Thermal Testing
A view of multiple testing stations for use in conducting Thermal Analysis on various materials. This is one of several areas assigned to various thermal tests. Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA), Thermomechanical Analysis (TMA), and Dynamic Mechanical Analysis (DMA)
-
product
Environmental Test Chambers
Infinity Machine International Inc.
Environmental Test Chambers by Infinity Machine International Inc. - for applications such as hydrostatic test chamber for soles, thermal shock chambers, temperature and humidity test chambers, rainproof testers, UV light testing, and more.
-
product
Leeb Hardness Tester
THL500
It is the highest brightness display in China showing all functions and parameters, easy read Largest screen Oled screen and operate,also can save lots of energy .the largest screen of Leeb hardness tester in China. Two hardness scale dual-display in the screen. Measuring direction in 360 and add the auto measure direction to make test easy and precision. Add four new hardness scales, HRA, HB for D impact device of alloy tool steel; HV for cast aluminum alloy. Add New user material function, to ...show more -
product
Vibration Table Top system
OVTT 18
The OVTT, Omni-Axial Vibration Table Top system, is the first, stand-alone, compact, repetitive-shock vibration system on the market. The OVTT 18 system is ideal for No Fault Found (NFF) precipitation screens of field returns, repair verification and random vibration test of small products. The OVTT 18 utilizes Qualmark's patented six-degree-of-freedom vibration technology and is designed with reduced air requirements and low noice levels. The OVTT 18 system can be easily configured for placement inside a thermal chamber for combined stress tests.
-
product
28 cm2 Test Fixture Operations Kit
The 28 cm2 Cell Test Manifold Kit offers a highly effective solution for testing of individual planar solid oxide fuel cells. The kit contains all items necessary to easily mount cells with ~100 cm2 substrates. Designed for both long and short term experiments to measure properties such as fuel utilization, thermal gradients, red-ox cycling and longevity/degradation, these kits will accelerate your research and development activities.
-
product
Thermal Shroud
BC8-55/150C
When combined with a thermal conditioner such as the Bemco PCL3L-III or PCL3M-III, this shroud converts a 24 inch inside diameter by 30 inch high vacuum only vertical bell jar into a 19 inch inside diameter by 20 inch high thermal vacuum testing system. With a convenient clam shell door, test objects are easily loaded by simply raising the bell jar above the top of the door opening.
-
product
Walk-In Climatic Test Chamber
WEIBER climatic test chamber is ideally suited for specimen test requiring quick changes of temperature. It covers various applications from JEDEC and IEC test standards. The climatic chamber is equipped with advanced technology such as specimen temperature control which allows linear specimen temperature rates of change during rapid thermal cycling or accurate temperaThe walk in option provides facility to test large sized, heavy weight specimen as well as the facility to test the specimen in bulk. Capacities ranging from 2000 to 10,000 Lt are available. Standard as well as customizable sizes and facilities are provided.
-
product
PXIe-2529, 128-Crosspoint, 4x32 OR 8x16, 2-Wire PXI Matrix Switch Module
780587-29
128-Crosspoint, 2-Wire PXI Matrix Switch Module—The PXIe‑2529 is a high‐density PXI matrix switch module that you can configure as either a 4x32 or an 8x16 2‑wire matrix by using different terminal block accessories. It uses electromechanical relays that offer excellent performance for high-power signals and low thermal offset for accurate measurements at low-voltage levels. The PXIe‑2529 also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
Regenerative Battery Pack Test System
17020
Chroma's 17020 is a high precision system specifically designed for secondary battery modules and pack tests. Accurate sources and measurements ensure the test quality that is suitable to perform repetitive and reliable tests that are crucial for battery modules / packs, for both incoming or outgoing inspections as well as capacity, performance, production and qualification testing. Chroma's 17020 system architecture offers regenerative discharge designed to recycle the electric energy sourced b...show more -
product
Climate Chamber
ICH
Its excellent temperature and humidity homogeneity positions the climate chamber ICH in the international top league of stability test chambers. Thermal transfer to the interior whether heat or cold is guaranteed through a large-area air jacket on four sides. Thanks to its hermetically sealed interior, the climate chamber ICH does not consume any water once the setpoints have been reached, provided that the door is not opened. Two high-grade platinum temperature sensors with mutual monitoring guarantee interruption-free long-term operation even if one sensor should fail.
-
product
Thermal Abuse Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Thermal abuse test chamber is suitable for standard IEC 62133-2017, UL 1642 and GB 31241-2014.
-
product
Milliohm Meter
16502
Chroma Systems Solutions, Inc.
Basic accuracy : 0.05%Pulsed test current output mode is used to reduce thermal EMFs affection on milliohm measurementDC test current output mode is used to fasten measurement speed for inductive DUTDry-circuit test current output mode (limited Max. 20mV) is used to measure such contact resistances where the maximum open-circuit voltage must be limited to 50mVTemperature correction (TC function) regardless of material or temperatureUseful temperature conversion function for motor/ coil evaluatio...show more -
product
PXI-2568, 31-Channel, 2 A, SPST PXI Relay Module
778572-68
31-Channel, 2 A, SPST PXI Relay Module—The PXI‑2568 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2568 is fully software programmable. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
product
TIM Characterization Tools
Thermal Engineering Associates, Inc.
Combining Thermal Test Vehicles (TTVs) with Thermal Test Boards (TTBs) results in a set of tools that perform the basis for TIM thermal characterization under application-oriented measurement conditions. Availability of these tools creates a de facto standard that enable both TIM manufacturers and TIM users to compare measurement results under the same conditions.
-
product
OSFP 800G
OSFP800 has emerged as a leading standard to drive the development of 800G ecosystem. The MultiLane OSFP800 development kit is an essential tool to ensure the validity of your OSFP800 products. The module compliance board (MCB) is used to test transceivers, AOCs, active cables and DACs, while the host compliance board (HCB) enables the testing of system host ports. The loopback modules (LB) provide an economical way to test thermal capacity and signal integrity of system host ports at every stage of the process: R&D validation, production testing, and field testing.
-
product
Test House Services
At TS-Space Systems we have over 30 years experience in designing, building and operating vacuum systems for space simulation and materials testing. We have three in-house thermal vacuum chambers which are configurable for a range of temperatures for either monitored vacuum bakeout or thermal vacuum cycling. We design, build and operate these systems in-house which means we are more flexible than most test houses and are happy to modify feedthroughs, manufacture additional support equipment and even change the operation of the chambers, where possible, in order to accomodate customer requirements.
-
product
Explosion Proof UV Inspection Light
he Labino MB Hercules Ex is an extremely durable product specifically developed for use in areas where the risk of an explosion is high. Offshore Oil Rigs, Refineries, Aerospace, and Defense often require explosion proof products to ensure safety for their inspection teams. The Midbeam Hercules Ex has successfully completed extremely tough tests, including tests for thermal conditioning, Impact Tests, Drop Tests and IP tests that led to the ATEX certification (Certificate: ITS17ATEX402144X). This unique product is suitable for use in extreme weather conditions varying from 104° Fahrenheit (+ 40° Celsius) to minus 4° Fahrenheit (- 20° Celsius).
-
product
Double-deck High and Low Temperature Environmental Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Double-deck High and Low Temperature chamber was designed to test battery cell combined with charge and discharge equipment, and also available to thermal test for small products and components.
-
product
Scalable Multi-Channel Active Thermal Control (ATC)
T-Core Thermal Control System
Cohu’s proprietary T-Core thermal system’s controller provides precise, multi-site temperature management of power dissipation ICs, such as graphic chips and CPUs, optimizing test yield.The T-Core thermal control system optimizes test yield at cold, ambient, and hot temperatures and offers better than +/- 1°C accuracy with response speeds of >125°C/sec. The system’s flexibility to control air, liquid, and refrigerant based thermal heads gives semiconductor manufacturers excellent temperature control capability for high volume manufacturing.
-
product
Thermal Shock Chamber
The Thermal Shock Chamber is specially designedwith independant temperature zones to facilitatethe automatic transfer of product under testthereby simulating a temperature shock to test the reliability of the product as per military and other international standards.
-
product
Thermal Test Vehicles
TTV
Thermal Engineering Associates, Inc.
Using the TTC-1002 Thermal Test Chip as a basis, TEA offers TTVs in flip-chip, bare die, BGA packages for a variety of thermal simulation, reliability, qualification, heat sink characterization, and TIM characterization activities. Selective unused balls are sequentially connected together for daisy-chain applications.
-
product
Thermal Monitoring System
The monitoring system for the thermal state of traction electric locomotive machines is designed for:control of the thermal state of traction electric motors (TED) as part of a high-speed traction-energy car-laboratory for testing rolling stock (TEL-C) in the acceptance and certification tests of electric locomotives;control of the thermal load of the TED and the temperature distribution by volume of the TED during the operational tests of electric locomotives;experimental determination of the m...show more