Filter Results By:
Products
Applications
Manufacturers
-
product
PXIe System Sync Module, 5 Port
M9033A
The M9033A PXIe System Synchronization Module is a dual-slot, 5-port module that provides multi-module and multi-chassis synchronization and triggering for Keysight's modular instruments.
-
product
PXIe System Sync Module, 2 Port
M9032A
The M9032A has a Soft Front Panel (SFP) that provides a graphical user interface to the system sync module. It allows the user to set up the most commonly used functionalities of the module. The SFP also gives you the ability to check the module's connection status, configure the reference clock and IO settings, and perform firmware udpates.
-
product
Chassis
United Electronic Industries, Inc.
Two independent Gigabit (1000/100/10Base-T) Ethernet InterfacesOne port for Control, the second for diagnostics orBoth ports bonded/teamed for redundant network accessCompact: 2.7" x 4" x 4.1"Over 60 different I/O configurationsRugged: 100 g shock, 5 g Vibration, −40 to +70 °C, 0 – 70,000 feetReal-time: 1000 I/O scans in < 1 millisecondInter-device sync interface
-
product
Corona Effect Camera
CoroCAM 8 UAV
*High-sensitivity UV detector, which can detect UVc light at 2.05×10-18 Watt/cm2, this allows detection of the smallest corona discharges.*9Hz (or 25Hz optional) IR radiometric camera module*Control of a limited number of camera functions from a standard RC controller using PWM or SBUS.*Remote control of all camera functions from the laptop via an Ethernet link.*Soft sync or staggered zoom of the 3 channel cameras. The IR and UV channels are digitally zoomed in, which is visible...optically zoomed in to the minimum FOV, and then digitally zoomed out.
-
product
Digital/Analog Frequency Response Analyzer
8800 Series
The analyzer utilizes a digital “Sync” signal to provide synchronization between analog and digital hardware. The Model 8800 performs simultaneous analysis on both analog input channels and digital target processor, reliably capturing all data. Versatile by design, the Model 8800 digital interface can be disabled, via software, to use the analyzer in a standard 2-channel, analog-only configuration.
-
product
Dual Channel Bit Synchronizer for Rates up to 45 Mbps
LS-45-DB
The Lumistar LS-45-DB Dual Channel Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digitaldesign assures a high performance, consistent product, with excellent reliability and long-term stability. Dual channel design can feed each channel of the LS-55-DD dual decom. The LS-45-DB also has a post D combiner that allows for optimal ratiocombining of the two input signals A unique Built-in-Test feature allows performance verification for the Bit Synchronizer to ensure the highest level of operation. Auto-test BIT is performed for a short duration on the application of power and tests more than 90% of the Bit Synchronizer components. This test verifies that power is properly applied, verifies that there are no internal bit errors, and performs other tests to ensure that the bit synchronizer is fully operational with status indication of results. Command-test BIT performs the same functions and can be initiated by the user at any time through the Lumistar software when used on Lumistar PC products. The user has the ability to generate internal pseudo-random patterns and calculate internal bit error rates with or without the injection of forced errors.Various status indicators are also available through the software. The Bit Synchronizer also contains a BER reader as well as frame sync pattern indicator.
-
product
IF-to-IF Converters
The new generation of wide-band and ultra-wideband tuners have output frequencies as high as 4 GHz and 6 GHz. These frequencies are often out of sync with adjacent and peripheral equipment. The IFAT-8000 has an input range up to 8 GHz, can process a BW of 1000 MHz (or lower) and can convert/translate the IF to a frequency and bandwidth that is manageable by downstream assets. As times and applications change, the IFAT can change with the new needs.
-
product
Isolated Timing Repeater
The Isolated Timing Repeater (previously known as the MOFR) is a compact DIN rail mountable signal repeater that performs a number of tasks, including converting time sync signals , boosting signal strengths and converting one type of signal to another.
-
product
Master Reference Generator
Mentor
Precision Time Protocol IEEE-1588 PTP grandmaster• Multiple video and audio formats in one box• Simultaneous 525/625 and HD Tri Level Sync outputs• Highly accurate GPS reference for synchronisation and timecode• Vector web-browser setup and monitoring tool• Redundant PSU option• Add upgrades and options without return to factory• Generates synchronised audio and video• Redundant units with changeover• 4K test pattern ready (future upgrade)
-
product
Multi-Band Dual-Channel Receiver/Combiner, Modular Unit with Integral Tracking Receivers and Bit Syncs
LS-28-DRSM Series
Lumistar offers the LS-28 series of high performance multi-band multi-mode RF Receiver/Combiners in several different versions including rack mount, portable and modular formats. Complete solutions from RF to bits and/or RF to UDP data broadcast in Chapter 10 format are available. Available at any frequency range from 215 MHz to 6000 MHz, data rates to 50 Mbps.
-
product
Multi-Interface Frame Grabber
Xtium 2 CLHS PX8 LC
The Xtium™ 2 CLHS PX8 features CameraLink HS standard on the PCI Express™ Gen 3.0 platform. This single cable, single slot solution supports up to 4-CLHS lanes, each operating at 10.3 Gbits/s, to acquire images at up to 5.0 GBytes/s and transfer them using PCIe x8 slots to the host memory. The Xtium2-CLHS supports Active Optical Cable (AOC) to extend the cable length beyond 100 meters. Built-in data-forwarding and multi-board sync capabilities deliver a platform for distributed processing for high-speed, computational intensive machine vision applications.
-
product
Pattern Generator
AVLINK TECHNIC TAIWAN CO., LTD.
* Intelligent functionality. * With 162 MHz pixel frequency. * Support total 38 timings. (up to UXGA) * Support Sync Type: H/V (TTL), SOG. * Low cost. * Single interface easily use. * Portable design, working time up to 8 hours by inside Re-chargeable battery. * Auto Power-off on Battery mode. * Provide total 34 patterns, Include: Color bar, Gray, Grid, Block¡K * By 16x2 Character LCD and key buttons, easily control.
-
product
PD Coupler
Techimp Capacitive PD Couplers offer both the PD and sync signals references, allowing a thorough investigation of the signal originating inside the asset they are connected to.Techimp Couplers are individually tested according to the following international standards: IEC60358; IEC60694; IEC60270.
-
product
Phase Meter
PM1
The Phase Meter PM1 provides a simple method of synchronising the field sync of two line locked CCTV cameras without the need of a dual-beam oscilloscope.
-
product
PTP Toolbox
OSA 5410/11
The OSA 5410 Series is a family of compact and cost-effective synchronization distribution and assurance devices that bring the power of Syncjack™ to any network. Following a toolbox approach, the family members of the OSA 5410 Series can be utilized in a variety of network synchronization applications including IEEE 1588v2 Access Grandmaster, Boundary and Slave Clock, GNSS receiver and Primary Reference Time Clock (PRTC), synchronization signal conversion and sync probe applications.
-
product
Reference Generators
When rack space is at a premium and you need a solid reference generator with every signal imaginable – 4K, HD, 3 Gb/s, SD, analog composite, time code, AES, and more – look to Ensemble Designs.Used in TV stations, mobile trucks, news helicopters and flight packs world-wide, Avenue and BrightEye sync pulse generators and test signal generators are rugged and reliable.
-
product
RGB Video Driver
PCI900
The PCI900 is a PCIe form factor module that has dual RGB analog video receiver inputs. It outputs two analog RGBs that provide the capability to drive UXGA video up to 110 feet over coaxial cable. The input impedance is 75 ohms with a signal level of 1 VPPper RS-343A with sync on green. The output characteristic being 1 VPP into 75 ohms per RS-343A which can drive a minimum of 110 feet of cable.The PCI900 receives only power from the PCIe bus and has no other connection to the PCIe bus.
-
product
Serial analyzer
The Serial analyzer sink decodes analog data on a serial bus to serial data. It can be used to monitor and analyze RS232, RS485, MIDI, DMX or other compatible serial buses. The serial analyzer can monitor up to eight sources. When these sources are in sync (all sources are of one (combined) instrument), all captured data will be displayed in chronological order.
-
product
Serial I/O Boards
Serial Mode Protocols include Asynchronous, Bisync, SDLC, HDLC, IEEE 802.3, Synchronous Telemetry, Simple Clock/Data ("-SYNC" product line), Di-phase and SPI Interface. Transceiver support RS485, RS422 (V.10), RS232 (V.28), RS423, V.35, RS530, as well as other software selectable mixed protocol modes Up to Eight Independent Serial Channels per Board Synchronous Serial Data Rates up to 10 Mbits/sec Asynchronous Serial Data Rates up to 1 Mbits/sec PMC and cPCI rear I/O support Custom Protocols Available
-
product
Sync Generator
LT 4610
The LT 4610 is 1RU full-rack size sync signal generator that can output triple-rate SDI (3G-SDI/HD-SDI/SD-SDI) signals. It employs two power supply units for redundant operation to protect against power supply failures. The genlock function for external sync signals enables SDI signals, six sets of analog black burst sync signals, and audio word-clock signals to be output synchronously. The genlock function is equipped with a STAY IN SYNC function that maintains the phase when errors occur in the input signal, making it possible to provide stable sync systems.In addition to test pattern output including color bars and SDI check fields, the LT 4610 can embed ID characters, QVGA logo marks, safety area markers, and embedded audio in a SDI signal output.
-
product
Synchroscopes
The range features 2 synchroscopes : LED synchroscope & LED synchroscope with check sync relay, both housed in 96x96mm DIN cases.
-
product
Test Pattern Generator Delay & AV Sync Analyzer
VQDM-100
Versatile compact and robust multi-purpose tool for R&D and glass-to-glass QA/QC Instant visual-aural quality estimation plus automatic latency, AV sync and 3D LR sync measurement Multi-channel time-line analysis, including video frames continuity testing 4 Light Sensors with vacuum caps, 4 Audio inputs (standard line levels) 2 channels of AV timing analysis, simultaneous measurements of Video and Audio Latencies Real time multi-channel data acquisition via USB port Unique sophisticated set of static and dynamic test patterns up to 1080p@60fps - see more details in separate VQL page Source of VQDM, VQMA2, and VQMA3 Test Patterns for VideoQ Analyzers Multi-format digital and analog AV outputs: HDMI, YPrPb, S-video, SPDIF, LR analog audio Networkable unit, easy expansion with any external USB storage device: live clips, user content, etc.
-
product
Universal Clock
DXD-8
The DXD-8 Universal Clock, a precision multiformat reference generator generates up to 4 independent video syncs and audio clocks simultaneously. With the PTP option, it acts as a bridge between an IP infrastructure and legacy A/V equipment.
-
product
Video Level Meter
VLM1
This meter provides a direct reading in volts of peak white and sync levels of a CCTV signal on a 4 digit LCD display. An input impedance switch provides slection between terminated (75Ω) and unterminated (high impedance) input.
-
product
75W to 250W - Single Output
i6A Series
*1/16th Brick Footprint*9-40 Vdc, 9-53 Vdc Inputs*3.3 up to 40, -3.3 to -30 Vdc Outputs*Up to 20 A max Output Current*Non-Isolated*Remote ON/OFF, Sense, Power Good, Trim*Sync, Sequencing
-
product
300W - Single Output
i7C Series
*Wide 1/16th Brick Footprint*9-36 Vdc, 9-53 Vdc Input*5-28, 8-24, 9.6-48 Vdc Outputs*Non-Isolated Step Up/Step Down*-40 to 125 °C Operating Temperature*Openframe, Baseplate or Heatsink options*Trim, On/Off, Power Good, Sync, Imon
-
product
10MHz Pulse Generator With Delay
TGP110
0.1Hz to 10MHz frequency rangeIndependent control of pulse frequency, width and delay50ns minimum pulse widthSquare wave, double pulse & delayed pulse modesFree-run, gated and triggered modes50 Ohm output: 0.1V to 10V amplitudeTTL/CMOS and Sync outputs
-
product
1U Quad Bit Sync for Data Rates up to 40 Mbps
LS-44-QBS
The LS-44-QBS contains up to 4 Lumistar LS-40-DB25 Bit Synchronizer Daughterboards in a 1U RackMount chassis with status lights on the front panel and all interconnections through the rear. The design contains an internal computer which runsoff DOS or Windows depending on the version selected. The DOS version boots quickly without the delays required for Windows startup. The Windows version offers networking. The unit can be connected directly to the optional 1U slideout keyboard/display, for setup resulting in only 2U of total rack height. For applications that require many bit synchronizers, a 1U keyboard/Display with KVM switch allows 32 bit synchronizers in 9U of rack height. When power is applied, the computer will operate with the last configuration unless the operator wishes to change the setup. For setup, the keyboard/display is pulled out and the display is flipped up to monitor the process. When the bit synchronizer setup is completed, the keyboard/display canbe closed up since the status can be monitored on the front panel without an external display.
-
product
Analog/SD/HD/3G Advanced Test Signal Generator
VSG-4TSG
The Videotek® VSG-4TSG is part of the Imagine Communications Reference Sync and Timing platform, and is a ½RU wide, 1RU tall and 12 inches deep 3G/HD/SD master timing generator. The unit is small in size, with redundant power supply inputs, and is low in power consumption and light in weight, making it a perfect fit for all broadcast television and post production environments.
-
product
Automatic Audio-Video Sync Detection
BATON® LipSync
BATON® LipSync is an automated tool for lip sync detection and verification. BATON LipSync leverages image processing and machine learning (ML) technology and deep neural networks to automatically detect audio and video sync errors. Using BATON LipSync, broadcasters and service providers can accurately detect audio lead and lag issues in media content in order to provide a superior quality of experience (QoE) to viewers.
