ECU Testing
test of Electronic Control Unit (Engine Control Unit) validating it and related dynamic systems.
See Also: ECU, ECU Simulation
- Canden Products LLC
product
Stability Testing Chamber - Double Door Model
Q20
Canden stability testing chamber is capable of maintaining stable temperature set points of 25°c , 30°c & 40°c and corresponding relative humidity set points of 60%RH(@25°c), 65%RH(@30°c) and 75% RH(@40°c) with exceptional precision. The chamber has a wide operating temperature range of 18°c t to 40°c maintaining a stable temperature across the entire range.
-
product
ECU Simulators
Easily configurable and customizable ECU solutions. Perfect for use as gateway nodes, simulators, automated testers, and ECU replacements.
-
product
ECU Simulator
PT-LabCar
PT-LABCAR is an open and scalable Hardware-in-the-Loop (HiL) system. It is designed for open- and closed-loop testing of ECUs specifically in the powertrain application domain. The system can be used to run automated regression tests for the release of software variants as well as for the validation of control and diagnostic functions in early phases of ECU development.
-
product
ECU & Bus Interface Modules
ES500
ETAS makes the entire software and hardware range available from program development to the calibration of your ECUs. You can use the ETAS tools to address all ECUs that satisfy the ASAM standard. By using these standardized interfaces, our tools are not limited to the ECUs of any particular manufacturer.
-
product
Configurable Simulation Of ECU Diagnostics.
TestCUBE2
Softing Automotive Electronics GmbH
The ECU simulation TestCUBE2 is the counterpart for all cases of application in which an ECU is not yet (e.g. preparation of workshop tests) or no longer (e.g. tester regression test) available. TestCUBE2 is a configurable hardware and software solution for simulating ECU diagnostics with real bus communication. With just one device, you can simulate several ECUs or even an entire vehicle at the same time.
-
product
Analysis Tool for ECU Networks and Distributed Systems
CANape
The primary application area of CANape is in optimizing parameterization (calibration) of electronic control units. During a measurement process, you can simultaneously calibrate parameters and record signals. The communication between CANape and the ECUs takes place via protocols such as XCP or via microcontroller-specific interfaces with the VX1000 measurement and calibration hardware. CANape supports various ADAS sensors such as radar, LIDAR and video. Combined with high-performance hardware,...show more -
product
Programmable ECU & CAN Gateway
MICROGen
MICROGen is a control prototyping hardware and software system. It has a range of uses, including as a communications gateway, during testing and for Rapid Control Prototyping.
-
product
ECU Software Download Stations
Jackmark Engineering design & manufacture ECU software download stations also known as flash stations, for several industry sectors including automotive, agriculture & utilities. The custom designed stations in either a single unit or multiple stacks provide a secure & reliable system of downloading software to electronic control units. Units are ‘locked in’ during the download phase with visual indicators of download status.
-
product
ECU Tester
State-of-the-art analog and digital technology are covered in the ECU, measurement and control systems and flexible high performance is required for the evaluation. Verification of reliability is very important because it is an important component further life-threatening people. From previous experience, tester of the ECU has come to our proposed notice that it is better to use a TestStand and PXI is the optimal solution of Peritec ECU tester.
-
product
Climatic Testing
Environmental Test Chamber. Environment Associates' complete Climatic test facilities offer precise simulation of Temperature, Humidity, Altitude, Thermal Vacuum, Salt Fog, Sand and Dust, and Rain as well as many other specialized environments. Microprocessor Control along with calibrated recorded measurements and outstanding attention to detail by our technical staff make for a perfect test everytime.
-
product
Flight Testing
ATA Engineering has developed flexible low cost methods to satisfy our customers' flight testing needs. We are able to provide innovative solutions to acquire and process all types of flight testing data without requiring expensive software and hardware solutions.
-
product
Testing Software
Materials testing software packages are available for all new Instron systems and as upgrades to existing Instron systems. All software interfaces are designed to be natural extensions of the instruments for efficient test operation, while also providing a powerful post-test analysis tools, like DIC Replay, and data management tools, like TrendTracker™.
-
product
Loudspeaker Testing
TTC
The weakest link in your measurement chain is your chamber, the new TTC chambers solve these problems...*Anechoic chambers have massive footprints:The TTC gives you equal or better results with a compact footprint*Achieving repeatable measurements is difficult in an anechoic chamber:The TTC guarantees the microphone and loudspeaker positions*Anechoic chamber accuracy suffers at low frequencies:The TTC is capable of measuring below 20 Hz*Results are not transferable between most test chambers:The...show more -
product
Haptic testing
Haptic tests are becoming ever more important owing to the increasing and sector-independent popularity of switches and buttons in diverse products. More and more customers, especially in the automobile sector, attach great value to good haptic performance by their control elements. A precise switching feeling, low friction of the moving elements, backlash-free execution both in the rest position and during operation are only some of the criteria for good haptic switching characteristics.
-
product
Strength Testing
Sataton Instruments Technology CO., Ltd
Air permeability tester is professional designed to determine the permeability of materials to air. By testing the rate of flow of air passing perpendicularly through a given area of tested sample under a given pressure over a given time period, the tester can provide results of air permeability performance by calculation the indices. The air permeability testing instrument is applicable to many type of materials, including industrial fabrics, nonwovens, made-up textiles, paper and board, foam and other materials.
-
product
Disintegration Testing
Agilent offers innovative dissolution testing systems to accurately measure the disintegration of dosage forms into particles under standard conditions. The Agilent 100 Automated Disintegration Apparatus is a fully programmable solution delivering reliable disintegration testing results. Our disintegration testing systems are compact and easy to manage, featuring precise temperature control and meeting regulatory compliance requirements.
-
product
Module Testing
This product range offers 45V, 100V and 150V systems, with a 60A per channel capability. All systems support parallel switching for achieving higher currents. Each channel has an onboard CAN-bus connection for BMS interfacing and can be extended with auxiliary IO’s for single cell voltage and temperature measurements.
-
product
Integration testing
Integration testing primarily focuses on verifying data communication among different modules of the software project. Integration tests determine the effectiveness and performance of different software modules when they are connected to each other.
-
product
Accessibility Testing
It is a social responsibility to provide the perfect accessibility of software application to the differently-abled populations. ImpactQA ensures this by providing service across WCAG guidelines which are published by the Web Accessibility Initiative (WAI) of the World Wide Web Consortium to provide the best coverage in terms of accessibility testing quality. It is the only approach you can know for assured that your website, app, multimedia or electronic document is accessible to people with impairment. Usually, people with disabilities use convenient technology which helps them in operating a software product.
-
product
Semiconductor Testing
The integrated PXI platform and the open interfacing provides extension capabilities for additional testing requirements like DUT specific resistors-networks or temperature sensors. The Test System comes with the ready-to-run GTSoftware package and allows easy programming of test sequences (GTbuilder) and fast execution in production/test mode (GTengine).
-
product
PRODUCTS TESTING
ESD
MicroStat Laboratories -R.E.T.S.
Our ESD test capabilities include resistance, resistivity, electrostatic shielding, charge generation, and charge dissipation. We routinely test flooring materials, packaging, footwear, garments, ionizers and many other ESD control products and materials. We utilize the relevant test methods and standards of the ESD Association, ANSI, ASTM, NFPA, IEST, IEC, AATCC, or our clients’ in-house specifications.
-
product
MIL-STD Testing
MIL-STD-Testing encompasses a wide variety of categories that we provide including EMI/EMC, Environmental and Power Quality for ground, vehicle, ship and aircraft applications.
-
product
Memory Testing
C.C.P. Contact Probes Co., LTD.
Standard and Custom test solutions for RAM, Flash and many other memory chips.
-
product
Innovative Testing
Originally founded as a test house, the IPTE Group today has in-depth knowledge in all areas of testing and test automation. Our internationally producing customer groups value our expertise in all areas of measurement and test technology as well as the often combined technologies such as software flash or optical test for their quality assurance.
-
product
Wireless/RF Testing
NCEE’s experienced iNarte EMC/EMI qualified staff provide wireless and radio frequency (RF) testing of intentional radiators to ensure they meet the FCC, CE, and many other international regulatory requirements for transmitting and receiving (radio) devices. Frequent regulatory changes and complex testing requirements are common with wireless/RF equipment. NCEE Labs stays current with the most recent requirements and can help you navigate your requirements while supplying quality testing services to demonstrate worldwide compliance!
-
product
Microwave Testing
120
The MODEL 120 PICOPROBE® sets new standards in microwave probing performance. Benefiting from coaxial techniques, which have inherent low loss and low dispersion characteristics, the Model 120 Picoprobe®, achieves an insertion loss of less than 1.75 db (typical) and a return loss of greater than 15 db (max.) over its frequency range.
-
product
Three-Phase Testing
CMC 310
The CMC 310 is specifically designed for basic three-phase testing of protection and measurement devices. It is operated by the CMControl P software which runs on the CMControl P unit, a Windows PC or on an Android tablet. Its intuitive user interface and the test tools included are optimized for quick manual testing in the field.
-
product
Impact Testing
Educated Design & Development, Inc.
1250 g body includes release mechanism and striking element guide.250 g striking element comes with cocking knob and hammer head, polyamide face, is hemispherical with a radius of 10 mm, has a hardness of HR85-100.60 g release cone with a 10N release force.Single Impact Force models range from a 0.2 J Hammer to a 2.0 J Hammer.Custom padded carrying case included.
-
product
Acoustic Testing
Our acoustic testing experience includes acoustic qualification and evaluating sound pressure levels. We utilize microphones, pressure trans-ducers, and an acoustic intensity meter to record acoustic measurements.
-
product
5G Testing
Teradyne test solutions are at the forefront of the 5G test era. Why? We work with the leading semiconductor manufacturers and provide optimized test coverage for the major wireless standards. From emerging millimeter wave devices to the traditional sub-6GHz, our test solutions are already leading the way.
-
product
Battery Testing
BTS 200
This testing and maintaining battery system allows to perform measurement of battery voltage, discharging current test and testing of battery capacity. BTS 200 can be connected with external load unit ELU 200.