Filter Results By:
Products
Applications
Manufacturers
Temperature Chambers
Life test cycling of temperature accelerating electronic degradation.
See Also: Environmental Chambers, Chambers, Humidity Chambers
-
product
Climate Chamber
ICH
Its excellent temperature and humidity homogeneity positions the climate chamber ICH in the international top league of stability test chambers. Thermal transfer to the interior whether heat or cold is guaranteed through a large-area air jacket on four sides. Thanks to its hermetically sealed interior, the climate chamber ICH does not consume any water once the setpoints have been reached, provided that the door is not opened. Two high-grade platinum temperature sensors with mutual monitoring guarantee interruption-free long-term operation even if one sensor should fail.
-
product
Compact Humidity Chambers
FW1.5
The Bemco FW1.5, mechanically cooled Compact Humidity Chamber, has a temperature range of -28 C to +177 C (-20 F to 350 F) or -73 C to +177 C (-100 F to 350 F) and a humidity range of up to 5% RH to 95% RH. This chamber features direct dry air injection and a direct humidity sensor.
-
product
Compact Temperature Chamber
FB1.5V-UHC Series
Based on the proven Bemco FB1.5V Compact Temperature Chamber, the FB1.5V-UHC offers spectacular temperature change rates in excess of 75 C per minute. With an extremely compact footprint these chambers cost about 1/3 of the amount of a typical 2-zone thermal shock chamber such as a Bemco FS2V.
-
product
Compact Temperature Chambers
Despite its compact size, the MC series provides top performance, with the lowest temperature range of it's class. Two types of control instrumentation are available: Our top-of-the-line SCP-220 touch-screen programmer for temperature cycling tests. Our economical T-instrumentation for fixed temperature operation.
-
product
Compact Temperature Test Chambers
TJR
Specifically designed these benchtop and floor chambers to have a compact exterior yet an ample interior workspace to maximize valuable floor space. Temperature Range: -73C - 200 °C. Internal Dimensions: WxDxH (inches) 16 x 11 x 11.75.
-
product
Compact TLP/VF-TLP/HMM Probearm Set for Temperature Measurements
PHD-4001A
High Power Pulse Instruments GmbH
*Electrically isolated probearm kit for VF-TLP, TLP, HMM, HBM force and sense probingbased on the GGB Picoprobe Model 10 replacement probe tips*Buried coaxial cable channel for thermo-chuck in isolated chamber temperature measurements*Compatible with GGB Picoprobe Model 10 replacement probetips*Compatible with all standard micropositioner interfaces*High precision rotation of the probearm by backlash-free 80:1 gear*Rugged stainless steel design*SMA connectors
-
product
Cytogenetic Drying Chamber
CDS-5
Developed in cooperation with Mayo Clinic, Thermotron's Cytogenetic Drying Chamberthe CDS-5was specifically designed for conducting cytogenetic slide drying tests during harvest of in situ and non-in situ grown cultures. The CDS-5 provides the optimum controlled temperature and humidity environment required to achieve ideal chromosome spreading results. As evidenced in research conducted by the Cytogenetics Laboratory at Mayo Clinic, the CDS-5 facilitates reliable and repeatable chromosome spreading. The use of an environmentally controlled drying chamber is a practical and cost effective way of achieving ideal chromosome spreading in a routine and highly consistent manner. Favorable chromosome spreading results can be obtained for both in situ and non-in situ cultures including PHA stimulated lymphocytes, bone marrow, amniocytes, and fibroblast.
-
product
Double-deck High and Low Temperature Environmental Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Double-deck High and Low Temperature chamber was designed to test battery cell combined with charge and discharge equipment, and also available to thermal test for small products and components.
-
product
Double-deck High Temperature Aging Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Double-deck High Temperature Aging Test Chamber is widely used to the aging test for electronic products, solar panel, plastic products, especially for battery temperature aging test.
-
product
Envinronmental Chambers
MRC environmental test chambers with temperature and humidity control. Chamber Test Humidity and Temperature Programmable humidity and temperature of range full a simulates freezing, climatic, durability, reliability test to conditions .etc endurance thermal, assurance quality.
-
product
Environmental Simulation Chambers
GTEMCELL , currently provide environmental test chambers made by LIB.Our standard range of test chambers includes bench top and floor standing models, across temperatures ranging between -65℃ and +150℃ (from -80℃ to +200℃ for specific applications), and humidities between 10% and 98% RH.
-
product
Environmental Test Chamber
Test Chambers are used widely in temperature variation tests, cold resistance tests, and for low-temperature storage in the areas of aerospace and aviation, electronic instruments, electrical products, materials, parts, and components.
-
product
Environmental Test Chamber
The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip.The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1 and humidity is 0.1%R.HThe temperature sensor is platinum PT100 Ohms/MV resistor
-
product
Explosion Proof Temperature Test Chamber for Power Battery
Komeg Technologies Explosion Proof Temperature Test Chamber for Power Battery
-
product
Fuel Tank Chamber
CSZ's fuel tank test chamber is designed to test the quality and reliability of automotive fuel tanks. Fuel tanks are temperature conditioned to -40C (-40F) along with a glycol mixture that is also chilled to -40C (-40F). The fuel tanks are filled with the glycol fluid and placed into the -40C (-40F) chamber. Tanks are soaked in the chamber for a predetermined length of time, removed from the chamber, raised to a specific height, and then dropped.
-
product
Gas Online Analyzer
OMA-100
OMA-100 gas online analyzer is a new generation of online gas analyzers which was independently developed based on the world's leading non-dispersive infrared gas analysis technology. It adopts a half-air chamber gas circuit design, with higher measurement accuracy, lower drift, and less influence from external interference (temperature fluctuati
-
product
Glass Door Humidity Chambers
FW30
The Bemco FW30, mechanically cooled, Glass Door Humidity Chamber has a temperature range of -18 C to +94 C (0 F to 200 F) and a humidity range of up to 5% RH to 95% RH. This chamber features dry air injection and a direct humidity sensor. It operates without dewpoint limit from 5% RH to 95% RH over the range of 30 C to 85 C and even allows operation at 20% RH at 5 C and 50% RH at -14 C!
-
-
product
High and Low Temperature Thermal Shock Chamber
HLST-500D
The specimen is placed in test chamber specimen which cannot be placed in high temperature chamber or low temperature chamber. High temperature chamber pre-heats the air and low temperature air chamber pre-cools the air. When doing the test of temperature changing from high to low, the low temperature chamber will blow the pre-cooled air to the test chamber. Then, the air in test chamber will reach your target temperature in several minutes (“recover time”). When doing the test of temperature changing from low to high, the high temperature chamber will blow the pre-heated air to the test chamber. Then the air in test chamber will reach your target temperature within the recover time.
-
product
High Temperature Axial Extensometers
4 models cover a variety of applications for high temperature testing 1 un-cooled model for use inside chambers up to 600 °C (1000 °F) Other models for use with split furnaces and induction heating, up to 1600 °C (2900 °F)
-
product
HPPlife for Keeping Mice
HPP750life
In a Memmert constant climate chamber HPP750life mice can be kept in a "specific pathogen free" (SPF) state. Ideally the climate chamber is located in a clean room. In order to guarantee the recommended humidity of between 45 and 65 % rh for the humane keeping of mice even at low temperatures, Memmert integrated a compressed air drying unit. For simulation of the day and night rhythm, the LED illumination can be programmed using the AtmoCONTROL software.
-
product
Humidity Chamber
HCP
Does your application temperature lie between 8 C above room temperature and 90C, with controllable humidity? Then the Memmert humidity chamber HCP is unbeatable in price, performance and comfort. The almost unlimited programming possibilities of temperature profiles make ideal environmental conditions for the load possible.
-
product
Humidity Chambers
FW Series
The Bemco FW Series of mechanically cooled Glass Door Humidity Chambers have a a temperature range of -28 C to +177 C (-20 F to 350 F) or -73 C to +177 C (-100 F to 350 F) and a humidity range of up to 5% RH to 95% RH.. These chambers feature direct dry air injection and direct humidity sensors. They operate without dewpoint limit from 5% RH to 95% RH over the range of 30 C to 85 C and even allow operation at 20% RH at 5 C and 50% RH at -14 C!
-
product
Laboratory Freezer
FZ Series
The FZ series laboratory freezer chambers are designed for performance specifications exceeding FDA and ICH requirements. The FZ series freezer chambers comes standard with the following performance: Solid- State Temperature Control. Autodefrost. Standard Microprocessor Controller with PID, Autotuning, programmable alarms (hi/lo), ability to ramp/soak, process variable and setpoint variable offset, dual display of actual temperature and setpoint temperature (process variable and setpoint variable). Controls are able to be quickly exchanged for future upgrades or repair.
-
product
Laboratory Incubators
DB & TE Series
These laboratory incubators have a wider range of temperatures. Also, these might be purchased if the role of the chamber might switch in future use – for example from cooler to above ambient temperatures. We have two types of heated and cooled incubators. The DB series incubators use compressor technology and have temperature ranges of 4°C-60°C. The TE series incubators use thermoelectric technology and have temperature ranges of 20°C-60°C.
-
product
Larger Size Chambers
Platinum
The ESPEC Platinum series are top quality temperature/humidity chambers in larger sizes for temperature cycling of 2 to 15°C per minute. High performance, reliable Scroll compressors(most units). One adjustable shelf with heavy-duty support rails. Non-metallic thermal breaks at doorframe and cable ports to eliminate exterior frosting or hot spots
-
product
Liquid Thermal Shock Baths
TSB Series
CSZ's Liquid thermal shock chambers consist of separately controlled hot and cold baths. Product is submersed in fluid and thermally stressed between the hot and cold baths, resulting in immediate product temperature changes. CSZ uses perfluorinated fluid that does not coat the product or conduct electricity for use in both the hot and cold baths to eliminate cross contamination and reduce evaporation losses.
-
product
Muffle Furnace
K585
Chongqing Kailian Yongrun Industrial Co.,Ltd.
Heating elements: MoSi2, SiC, Resistance wireWorking voltage: AC 220V, Single phase, 60Hz/50Hz(or at your option)Temperature accuracy: 1 degree CelsiusHeating rate: 0 - 15 degrees Celsius/Min (recommend less than 10 degree Celsius)Chamber size: different chamber sizes for your choice.
-
product
Plant Growth Chambers –
PG Series
Darwin Chambers PG Series Plant Growth Chambers is a stock design with a variety of customizable options. It is quiet, easy to clean, highly reliable and ideal for plant growth use It offers hot gas bypass control of refrigeration and resistive to heat to facilitate reliable, temperature and humidity control.
-
product
Probe Station
ETCP1000
Installation of “Hot and cool chuck” - Sellectable chuck size : 4inch, 6inch. - Temperature variation : -193°C ~ 300°C (80K ~ 573K) - Additional requirements : Vacuum chamber, LN2 tank(Bombei), microscope, CCD camera, manipulators. - EPS500 is standard model in ETCP1000 probe station.
