Filter Results By:
Products
Applications
Manufacturers
Mezzanines
Is the stacking of cards into a single card that then plugs into the computer bus or data path.
-
product
Carrier Card
SPR518
The SPR518 provides a smart upgrade path to affordably replace the existing SPR418A PCI Express (PCIe®) carrier for XMC modules. The new card provides for unimpeded data transfers within traditional PCs, at the full rate supported by the mezzanine card.
-
product
Carriers
VadaTech carriers are available in a wide range of mezzanine styles and formats, including versions to enable you to adapt different buses and architectures. These carriers are designed to enable you to build a complete system using best-in-class building blocks or legacy products regardless of the form factor.
-
product
CompactPCI (3U) Generic Carrier Card For PMC(PCIbus Mezzanine Card) Modules
ACC-1
cPCI (3U) generic carrier card for PMC (PCIbus mezzanine card) with 1 PMC slot. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
product
Current Meter
MTD32
The mezzanine module (mezzanine) MTD32 is designed to measure instantaneous current values over 32 channels.
-
product
Cyclone II FPGA with Digital I/O
IP-EP200
This series of plug-in mezzanine modules provides a user-customizable Altera® Cyclone II FPGA on an Industry Pack (IP) module. The module allows users to develop and store their own instruction set in the FPGA for adaptive computing applications.
-
product
DC Voltage Generator
MON8P
Mezzanine MON8P is designed to generate DC voltage in the range of ± 10 V through eight galvanically isolated channels from each other and from the case, which allows to reduce the level of interference and increase the safety of the device.
-
product
Digital Oscilloscope
MOS1
The mezzanine module (mezzanine) MOS1 is designed to convert instantaneous voltage values of an electrical signal into a digital code, measure instantaneous voltage values, measure time intervals between two instantaneous voltage values through two independent channels, measure the magnitude of the phase difference and the ratio of the amplitudes of two signals.
-
product
Electronic Resistance Store
MEMS5
Mezzanine MEMS5 is designed to reproduce the values of resistance to direct current through five channels independent and galvanically isolated from each other and from the case.
-
product
Electronic Resistance Store
MEMS2-4L
The mezzanine serves as an electronic store of resistance to direct current, the value of which is set by software, through two isolated channels.
-
product
Ethernet FPGA Mezzanine Card
Sundance Multiprocessor Technology Ltd.
Quad Gigabit Ethernet FPGA Mezzanine Card that can be integrated with the EMC2.
-
product
Ethernet Mezzanine Switch
P/XMC-651
Curtiss-Wright Defense Solutions
The XMC/PMC-651 is a 12-port Gigabit Ethernet switch packaged in the industry-standard XMC form factor. It is designed to support "in-chassis" networks with managed Layer-2 switching capabilities. Part of a family of Gigabit Ethernet switching/routing products from Curtiss-Wright Defense Solutions, the XMC-651 XMC/PMC Ethernet Switch is an ideal low cost zero-slot Ethernet switching solution that can be added to any basecard with an XMC mezzanine slot.
-
product
Ethernet Network Adapters
Available in PCIe NIC and OCP mezzanine 2.0 and 3.0 form factors, Broadcom’s Ethernet network adapters support configurations ranging from 1G to 200G, and utilizing both optical and copper connectivity.
-
product
Flight-Certifiable SBC
SBC314C
The SBC314C flight-certifiable single board computer is engineered in accordance with DO-178C and DO-254 and is available with supporting artifacts. It delivers great and proven performance thanks to the Power Architecture T2081 processor, and its diverse I/O set brings high functionality to the small form factor. The integrated XMC site allows even more connectivity, including high-density MIL-STD-1553 and ARINC 429 data bus communications as well as avionics discrete I/O through our RAR15CX flight-certifiable mezzanine.
-
product
FMC Card with Four SFP+ 10 GBit Ports
TEF0008-02
Sundance Multiprocessor Technology Ltd.
The Trenz Electronic TEF0008 is a FPGA to Mezzanine Card (FMC) based on VITA 57.1 FMC HPC Standard, with four SFP+ 10 GBit ports for fiber optical SFP modules. It is inteded for use on a FMC HPC carrier and can not be used stand-alone.
-
product
FMC Dual ADC 12-bit 2.6 GSPS, Single DAC 16-bit 12 GSPS
FMC250
The FMC250 is an FPGA Mezzanine Card (FMC+) per VITA 57.4 specification. The board has dual ADC and single DAC. The FMC250 utilizes dual AD9625 ADCs providing 12-bit conversion rates of up to 2.6 GSPS and a single DAC (AD9162 or AD9164) providing 16-bit conversion rates of up to 12 GSPS. The analog input, digital output, clock and trigger interfaces of the FMC250 are routed via SSMC connectors. The internal clock frequency is programmable and the clock is capable of locking to an external reference.
-
product
FMC for High Speed Optical Communication Dual QSFP+ FMC
FMC424
Sundance Multiprocessor Technology Ltd.
The FMC424 is a dual QSFP+ FPGA Mezzanine Card. Electrically compliant with the VITA 57.1 standard the FMC424 is compatible with 4DSP FPGA carrier cards offering High Pin Count connectors. It also allows for the option to stack an additional FMC over it. Any of the 4DSP FMC that use LVDS and single ended signaling only can be mounted over the FMC424, thus offering users with the ability to build a complete high speed data acquisition, waveform generation and optical communication solution while using a single FMC site on an FPGA carrier card.
-
product
FMC Mezzanine Dual or Quad Canbus
NES-FMC-CAN
Sundance Multiprocessor Technology Ltd.
This is a Dual or Quad CANbus with autotest capabilities that can be used on a wide range of carriers, Standalone, PCIExpress, CompactPCI, VPX, CompactPCI Express, AdvanceTCA and AMC.
-
product
FMC Mezzanine Module
NES-FMC4ADC
Sundance Multiprocessor Technology Ltd.
By default this card only uses signals from the LPC rows of the HPC connector that is mounted. The gain can be set by software in three steps: +/-50mV, +/-0.5mV, and +/-5V. AN advanced offset circuit is used in the front-end design of the ADC board, and allows a voltage shift in the range og +/-5V that is independent of the chosen gain range.
-
product
FMC Mezzanine Module, 4 or 8 Channel
NES-FMCSER
Sundance Multiprocessor Technology Ltd.
The FMC specification was developed to enable FMCs to be supported on a wide range of existing form factors including but not limited to, PCIe, VME, CompactPCI, VXS, VPX, VPX-REDI, AdvanceTCA and AMC. Up to three FMCs can be fitted on a 6U VPX carrier.
-
product
FMC Quad ADC 16-bit @ 1 GSPS and Quad DAC 16-bit @ 2.8 GSPS
FMC231
The FMC231 is an FPGA Mezzanine Carrier (FMC) per VITA 57 specification. The board has quad ADC (the ADC chips are dual channels) and quad DAC (the DAC chip is quad channel). The FMC231 utilizes TI ADS54J60 (option for ADS54J69) providing 16-bit conversion rates of up to 1.0 GSPS and a DAC DAC39J84 providing 16-bit conversion rates of up to 2.8 GSPS.
-
product
FPGA Card
PC820
The PC820 is a high-performance, PCI Express card with advanced DSP capabilities and multiple I/O options. It supports one FMC+ VITA 57.4-compliant HPC FPGA Mezzanine Card (FMC) that is closely coupled to the Virtex or Kintex UltraScale FPGA and a DDR4-2133 SDRAM SO-DIMM. The PC820s PCIe Gen3 interface can support up to eight lanes.
-
product
FPGA Mezzanine Card
FMC216
The FMC216 is a 16-channel DAC FMC daughter card which is fully compliant with the VITA 57.1-2008 standard. It provides 16 D/A 16-bit 312.5Msps (2.5Gsps with x8 interpolation) channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available.
-
product
FPGA Mezzanine Card
FMC126
The FMC126 is a quad-channel multi-mode A/D FMC, fully compliant with VITA 57.1 standards.The card provides four 10-bit ADC channels that enable simultaneous sampling of 4, 2, or 1 channel with a maximum sample rate of 1.25 GSPS (4-channel mode), 2.5 GSPS (2-channel mode), or 5.0 GSPS (1-channel mode).
-
product
FPGA Mezzanine Card
FMC120
The FMC120 provides four 16-bit A/D channels up to 1Gsps, four16-bit D/A channels up to 1.25Gsps and up to 2.8Gsps sample rate with interpolation. The devices can function up to 1Gsps during simultaneously D/A and A/D operation as the clock source is shared.
-
product
FPGA Mezzanine Card
FMC432
Sundance Multiprocessor Technology Ltd.
The FMC432 is a dual 10 Gigabit Ethernet (10GBASE-T) FPGA Mezzanine Card with two RJ45 connectors available on the front panel. Compliant with the VITA 57.1 standard the FMC432 is compatible with FPGA carrier cards offering High Pin Count connectors. It also allows for the option to stack an additional FMC over it. Any of the 4DSP FMC that use LVDS and single ended signaling only can be mounted over the FMC432, thus offering users with the ability to build a complete high speed data acquisition, waveform generation and communication solution while using a single FMC site on an FPGA carrier card.
-
product
FPGA Mezzanine Card
FMC176
The FMC176 is a quad channel ADC and dual channel DAC FMC. This daughter card provides four 14-bit A/D channels at 250Msps and two 14-bit D/A channels at 5.6Gsps (2.8Gsps direct RF synthesis) clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users.
-
product
FPGA Mezzanine Card
FMC116
The FMC116 is a 16-channel ADC FMC daughter card which is fully compliant with the VITA 57.1-2008 standard. The FMC116 provides 16 A/D 14-bit 125Msps channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available.
-
product
FPGA Mezzanine Cards
FMCs bring modularity to high performance I/O - whether you need high bandwidth ADCs and DACs for radar applications, Gigabit Ethernet for digital communications, or clock and trigger distribution for multi-board synchronization.
-
product
FPGA Module
NM-FMC
The new development of the Informtest holding, the NM-FMC mezzanine module, is a convenient means by which users can independently implement their own algorithms for receiving, transmitting and digital processing of information at the hardware level. The module contains an Altera FPGA of the Stratix III family, a clock generation unit, 8 GB DDR3 memory and a 160-pin LPC connector for connecting FMC mezzanines.
-
product
Frequency Converter up UHF AXIe-0 Up
AXIe-0 Up UHF Module
The AXIe-0 Up LMHF module is a carrier of mezzanine modules made in the AXIe-0 standard. The module ensures the functioning of various modules installed in it, made in the form of double mezzanines. The number of slots in the module is one.
