- Pickering Interfaces Inc.
product
PXI Simulation Modules For Sensor Simulation
PXI simulation solutions for sensor simulation, including PXI Programmable Resistors—ideal for the simulation of resistive sensors and PXI Thermocouple Simulators—these provide multiple low-voltage sources ideal for simulating the operation of a thermocouple. Take a look below for all of our PXI Simulation Solutions, we also offer some of these in PCI format as well . All of our PXI simulation cards are supplied with comprehensive software drivers for Windows® XP/Vista/7/8, Lab Windows / CVI and LabView. The Pickering IVI drivers also fully support National Instruments' Switch Executive.
-
product
AFDX ® / ARINC 664 Test And Simulation PMC Module
PMC-664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)Easy to use tool for configuring A*FDX® / ARINC 664 end systems (XML based)
-
product
E-Type Thermocouple, 32°F to 900°F Temperature Sensor
745690-E001
E-Type Thermocouple, 32°F to 900°F Temperature Sensor - The E-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the E-Type Thermocouple and acquire synchronized temperature data in units of degrees. The E-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
PXI-7841, Virtex-5 LX30 FPGA, 200 kS/s PXI Multifunction Reconfigurable I/O Module
780337-01
Virtex-5 LX30 FPGA, 200 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7841 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. T...show more -
product
VB-8054, 4-Channel, 500 MHz Bandwidth VirtualBench All-in-One Instrument
785037-05
4-Channel, 500 MHz Bandwidth VirtualBench All-in-One Instrument—The VB‑8054 combines a four‑channel, 500 MHz mixed-signal oscilloscope with protocol analysis, an arbitrary waveform generator, a digital multimeter, a programmable DC power supply, and digital I/O into a single device that integrates with your PC or iPad. The VirtualBench all‑in‑one instrument is simple and convenient and results in more efficient circuit design, debugging, and validation. The included software provides an interact...show more -
product
FlexRIO
The FlexRIO product line was designed for engineers and scientists who need the flexibility of custom hardware without the cost of custom design. Featuring large, user-programmable FPGAs and high-speed analog, digital, and RF I/O, FlexRIO provides a fully reconfigurable instrument that you can program graphically with LabVIEW or with VHDL/Verilog.
-
product
ISC-1782, 2 MP, 1.58 GHz Processor, Monochrome/Color Smart Camera
785151-01
The ISC‑1782 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all-in-one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic ...show more -
product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787455-01
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a hig...show more -
product
ISC-1783, 5 MP, 1.58 GHz Processor, Monochrome/Color Smart Camera
785154-01
The ISC‑1783 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all-in-one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic ...show more -
product
PXI Products
As we continue to innovate in PXI, our goals are to help you accelerate time-to-market and achieve a lower cost of test. Through a growing range of PXI and PXIe modular products, Keysight provides quality, performance and measurement expertise to bring you breakthrough capabilities. To help you quickly develop test systems with your software platform of choice, Keysight provides PXI modules with a comprehensive portfolio of instrument drivers, documentation and examples for Microsoft C/C++, C#, or Visual Basic, MATLAB, VEE, LabVIEW and LabWindows/CVI software platforms.
-
product
cRIO-9057, 1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 100T FPGA, 8-Slot CompactRIO Controller
786427-01
1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 100T FPGA, 8-Slot CompactRIO Controller - The cRIO-9057 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and eight slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with LabVIEW. The controller provides precise, synchronized timing and deterministic communications ov...show more -
product
High Voltage Switching Matrixes -15KV – 48Ch
H730035
Fast ATE technology: Modular, scalable and top flexible approach Minimum wiring and easy maintenance; LabVIEW drivers
-
product
ISC-1781, 1.3 MP, 1.58 GHz Processor, Monochrome/Color Smart Camera
785144-01
The ISC‑1781 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all‑in‑one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic ...show more -
product
Test Of Aviation Turbo Starter
The use of a 16-bit analog input board provided high measurement accuracy, and the use of the SCXI reconciliation system allowed the integration of signals from the most diverse sensors in one configuration. The software developed at LabVIEW implements all kinds of tests of turbo starters in full accordance with the approved methods.
-
product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781340-04
6.6 GHz PXI Vector Signal Generator—The PXIe‑5673E is a wide-bandwidth module that, when combined with the appropriate software, can generate a variety of signals. With the Modulation Toolkit for LabVIEW, it can generate different waveforms including AM, FM, CPM, ASK, FSK, MSK, PSK, QAM (4‑, 16‑, 64‑, and 256‑QAM), multitone signals, arbitrary waveforms, and many others. In addition, you can combine these vector signal generators with standard-specific software to generate signals for GPS, GSM/ EDGE/WCDMA, WLAN, WiMAX, DVB‑C/H/C, ISDB‑T, ZigBee, and others. With PXIe‑5673E stream‑from‑disk capabilities, you can generate continuous waveforms that are up to several terabytes in length.
-
product
Incorporated a Convenient LabView Interface to the Output
LabView VIs
Several VIs are available for plotting and monitoring pulse parameters. Update rates can be adjusted as well as the plots. The VIs are intended to be easily understood and easily modified for your particular application.
-
product
USRP Software Defined Radio Reconfigurable Device
The USRP Software Defined Radio Reconfigurable Device is built on the LabVIEW reconfigurable I/O (RIO) and universal software radio peripheral (USRP) architectures. It includes a powerful FPGA for advanced DSP that you can program with the LabVIEW FPGA Module. The device includes 2x2 MIMO transceivers or four-channel superheterodyne receivers, supporting center frequencies from 10 MHz to 6 GHz, with up to 160 MHz of instantaneous bandwidth. The USRP Software Defined Radio Reconfigurable Device a...show more -
product
PXI-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
778572-12
7-Channel, 10 A PXI Signal Insertion Switch Module—The PXI‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
product
Temperature Measurement System
TMM-100
Thermal Engineering Associates, Inc.
The self contained TMM-100 module accepts diode, thermocouple and thermistor temperature sensors. The USB-connected instrument is supplied with Windows™ 7, 8 & 10 compatible software that provides for sensor measurement on a cyclic basis and for data logging of all measured values. LabVIEW™ Virtual Instrument (VI) drivers are available as an extra cost option for users that wish to incorporate the TMM-100 into an application-specific measurement environment.
-
product
cRIO-9048, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 8-Slot CompactRIO Controller
785619-01
1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 8-Slot CompactRIO Controller - The cRIO-9048 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 160T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and determin...show more -
product
ARINC 664 Part 7 XMC Interface Module
XMC-664-V2
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message s...show more -
product
FlexRIO Custom Instruments And Processing
FlexRIO Custom Instruments and Processing products provide high-performance I/O and powerful FPGAs for applications that require more than standard instruments offer. Program these products with LabVIEW to create solutions for whatever challenge you’re facing.
-
product
cRIO-9049, 1.60 GHz Quad-Core CPU, 4 GB DRAM, 16 GB Storage, -20 to 55 °C, Kintex-7 325T FPGA, 8-Slot CompactRIO Controller
785618-01
1.60 GHz Quad-Core CPU, 4 GB DRAM, 16 GB Storage, -20 to 55 °C, Kintex-7 325T FPGA, 8-Slot CompactRIO Controller - The cRIO-9049 is a rugged, high-performance, customizable embedded controller that offers Intel Atom quad-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 325T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and determinis...show more -
product
FlexRIO Digitizer Device
FlexRIO Digitizer Devices feature high-performance analog-to-digital converters with lightweight analog front-ends designed to maximize sample rate, bandwidth, and dynamic range. These devices use FPGAs from Xilinx alongside LabVIEW and Vivado programming options for custom algorithm implementation and real-time signal processing. These devices also feature an auxiliary I/O connector with GPIO for triggering or digital interfacing and the option for high-speed serial communication.
-
product
ATE System Integration
Cyth Systems is a Systems Integration Company specializing in Automated Test (ATE), Embedded Controls, and Machine Vision. Our skilled and experienced team uses their natural talent for problem-solving to create solutions in a wide range of industries. We build our solutions starting with the National Instruments (NI) platforms including LabVIEW and PXI, and by adding best-in class sensors and components.
-
product
K-Type Thermocouples Wire, Fiberglass (32deg F to 900deg F) 2 m
745690-K002
K-Type Thermocouple, 32°F to 900°F Temperature Sensor - The K-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the K-Type Thermocouple and acquire synchronized temperature data in units of degrees. The K-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
ISC-1782, 2 MP, 1.58 GHz Processor, Monochrome/Color Smart Camera
785148-01
The ISC‑1782 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all-in-one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic ...show more -
product
USB-7846, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
783201-02
Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7846 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7...show more -
product
System Integration
G Systems develops fully integrated systems and we know that both software and hardware are equally important to system design. Our focus on code quality and optimization ensures customers receive efficient and maintainable code. We specialize in LabVIEW development and all of our LabVIEW developers are certified developers or architects. We’re also highly skilled in mechanical and electrical hardware design and builds on a wide variety of data acquisition, signal conditioning, RF, and distributed communication platforms.
-
product
ISC-1781, 1.3 MP, 1.58 GHz Processor, Monochrome/Color Smart Camera
785145-01
The ISC‑1781 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all‑in‑one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic ...show more -
product
Compact Juno USB Interface
Juno 7Z01250
*Virtual laser power meter - From sensor to interface to PC - no power source needed*Plug and play with all standard Ophir smart sensors*Use with StarViewer free Android app to turn your smartphone / tablet into a power meter*Record every energy pulse at up to 10 KHz*Log power and energy, average, statistics, histograms and more with included StarLab application*New: Pulsed Power measurements with Thermopile sensors*New: Low Frequency Power on Photodiode sensors - power measurement based on pulse cycle (for VCSEL)*System Integrator Tools included: LabVIEW VIs, COM Object Interface*Very compact - is just an extension of the smart plug
