Filter Results By:
Products
Applications
Manufacturers
-
product
Power Take-Off (PTO) Shaft Power Monitoring System
Series 420
Datum Electronics Series 420 PTO (Power Take-Off) drive shaft torque & shaft power monitoring system is designed to monitor and log the torque, shaft speed and transmitted power from all standard PTO shafts.Efficient measurement and monitoring with a PTO shaft power can prove to be a useful tool in research and analysis into the performance of a tractor’s transmission system highlighting efficiency savings, measurement and control.
-
product
Marine Shaft Power Meter Systems
Datum’s Marine Shaft Power Meter Systems are developed to provide real time and ongoing power monitoring data on propulsion shafts, thrusters and diesel generators. These devices are commonly used for fuel economy monitoring and equipment maintenance planning programs and can be used in conjunction with our EEXI | ShaPoLi solution to keep vessel owners in line with the latest legislation.
-
product
EEXI Shaft Power System (SHaPoLi)
Datum Electronics Ltd has developed a shaft power limitation (SHaPoLi) EEXI Shaft Power System, providing the necessary features and functionality to comply with the MARPOL Annex VI, MEPC.335(76) EEXI regulations.Our system uses a Shaft Power Acquisition Module to constantly display, monitor and record propulsion shaft power to ensure compliance with the EEDI requirements relating to CO2 emissions for ships over 400 gross tonnage.
-
product
Shaft Power Measurement Solutions
Our marine shaft power meter systems measure shaft torque, power, propulsion, rpm and thrust (if required), to ensure optimum performance is maintained throughout the lifecycle of a vessel. Using highly accurate & reliable strain gauge technology, combined with cutting-edge electronics, our system has an accuracy of 0.1%. It can be installed and commissioned within 1-2 days on a variety of shafts including intermediate shafts, thrusters, propellers and controllable pitch propellers. Our technology, along with our expertise in dynamic sampling of strain gauges, enable us to unlock a significant amount of information regarding the performance of the engine & propulsion shaft, along with the propeller.
-
product
Battery Powered Telemetry Systems
Advanced Telemetrics International
ATi’s Battery Powered Telemetry Systems are ideal for transmitting coupled data signals from sensors, which are mounted on rotating shafts or machinery to a stationary receiver.
-
product
Rotating Dual Shaft Torque Sensors
RST SERIES
The RST- Series is our low range rotating torque sensors that are available in eleven full scale ranges of 10 through 30K inch pounds. The sensing element incorporates bonded foil strain gages of the highest quality along with coined silver slip ring and silver brushes for data transmission. The WR2, Flexural Natural Frequency, and Torsional Stiffness values as stated in the Dynamic Characteristics box below, are approximate and the tabulated data pertains to the torque pickup only, and does not include the effects of couplings or other rotating masses that would be part of a dynamic system.
-
product
Prop Shaft Torque Measurement Systems
Advanced Telemetrics International
ATi Telemetry Systems are typically used to transmit data from rotating shafts or machinery to a stationary receiver. The Miniature Strain Gage Transmitter can be attached to strain gages adhered to your shaft in order to transmit shaft torque and thrust while the system is running.
-
product
Terminal Blocks with System
The Phoenix Contact terminal blocks enable a high degree of flexibility in terminal strip design. Choose between various connection technologies and combine the terminal blocks by installing bridges in the double function shaft. The terminal block system features standardized bridging, marking, and test accessories.
-
product
Rotating Telemetry Systems
2100B Series
Advanced Telemetrics International
Are ideal for transmitting coupled data signals from sensors, which are mounted on rotating shafts or machinery to a stationary receiver.
-
product
Rotating Ring Disk Electrode
RRDE-3A
RRDE-3A is a constant rotation system for use in hydrodynamic modulation rotating ring disk electrochemistry. A 7 mm diameter electrode with short stainless steel shaft provides for a miniature and concentric circle electrode system that is capable for highly accurate rotation and modulation even at radial modulation rates or wave forms.
-
product
Inductively Powered Telemetry Systems
Advanced Telemetrics International
ATi Inductively Powered Telemetry Systems are typically used to transmit data from rotating shafts or machinery to a stationary receiver.
-
product
Gearbox Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
product
General Purpose Probes
PIT-12
PIT-12 General Purpose Probe for Pressurized Systems - 12'' #304 stainless steel shaft. Diameter is 1/16''. Immersible. Maximum temperature 350°C, Time constant 0.5 Seconds. Shaft Terminated in a sub-miniature Type T Thermocouple plug. 10 foot Sub Miniature Type T extension lead supplied. Not isolated.
-
product
General Purpose Probe
PIT-6
PIT-6 General Purpose Probe for Pressurized Systems - 6'' #304 stainless steel shaft. Diameter is 1/16''. Immersible. Maximum temperature 350°C, Time constant 0.5 Seconds. Shaft Terminated in a sub-miniature Type T Thermocouple plug. 10 foot Sub Miniature Type T extension lead supplied. Not isolated.
-
product
Motor Tester
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
Dual Station Loaded Motor Tester including Automatic Shaft Engagement, Automatic Bar Code Scanners, Full Spectrum Vibration Analysis (8 bands) with Automatic Accelerometer Placement and Reject Printer.
-
product
Rotor Tester
SL Series
Shanghai Aoboor Electric Co., Ltd.
Applicable for testing fully opened, fully closed squirrl-cage rotors with process slot, with or without shaft, it can identify broken bars, slim bars, under-casting, porosity, sand holes, residues, improper end rings, internal short circut in bars, eccentricity.
-
product
Primary Injection Circuit Breaker Tester
PI-5000
The PI-5000 is composed of the PI2500 and the AUX-5000 auxiliary output unit, which when combined gives the unit the capability of testing 4000 ampere breakers, with essentially the same specifications as the proven PI-4000B. The auxiliary unit is smaller than the PI2500, so it can also be maneuvered easily in tight spaces, or lowered into shafts and manholes that would not be possible with a larger single piece unit.
-
product
Shaft Voltage Tester™ Digital Oscilloscope
AEGIS®
Digital Oscilloscope and Multimeter with Conductive Microfiber Probe Tips. Is your motor safe from destructive shaft voltages? For the first time you can get all of the tools to find out in one place. The AEGIS® Shaft Voltage Tester™ Digital Oscilloscope bundle includes the AEGIS-OSC-9100 100 MHz digital osciloscope, shaft voltage probe tips, and a shaft grounding simulator. Armed with these tools, you can quickly and easily find whether your motors are at risk of premature bearing failure due to VFD-produced bearing currents.
-
product
Twist Testing
STT
The STT Shaft Twist Tester is a system designed for quickly testing of twist structures and/or twist-freed condition on shafts in seconds.
-
product
Tachometers
Is an instrument measuring the rotation speed of a shaft or disk, as in a motor or other machine.
-
product
*CNC Surface Texture Measuring Instrument
Surfcom C5
SURFCOM C5 allows customization of the workpiece feed unit and jig production to suit particular needs.Basic specifications are Type-C (mainly for cylinder heads, cylinder blocks, and other workpieces wherea 5-direction approach is required) and Type-S (for camshafts and other shaft workpieces that require arotary axis).
-
product
Optical Shaft Measuring System
The measurements and shape of the shaft or rotating partsare measured in an overwhelmingly short time. In our lineup, we can handle inspection and automation during production processes, so we can contribute to increased productivity at your company.
-
product
Solid Tungsten Probe Tips
ST Series
The ST SERIESof probe tips, available from GGB Industries, Inc., are precision crafted from a 0.020 inch (0.51mm) diameter solid tungsten shaft that is electrochemically sharpened to a specified point. These durable, 1.5 inch long solid tungsten shaft probe tips are for use in most standard micropositioners when probing an integrated circuit, pad, or line. A variety of radius point sizes from 0.5 microns to 10 microns are available to accommodate any probing need.
-
product
Propeller and Rotor Blade Strain Measurement Systems
Advanced Telemetrics International
ATi Telemetry Systems are typically used to transmit data from rotating shafts or machinery to a stationary telemetry receiver. The 2040BC Miniature Strain Gage Transmitter can be connected to strain gauges adhered to propellers or rotors in order to transmit blade strain or shaft torque in flight.
-
product
Analytical Gear Inspection Machine
KNM 2X / 5X series
Analytical gear inspection machine for workpieces up to Ø 650 mm. Measuring machines for spur and helical gears, rotors, bevel gears, gear tools, shafts etc. Ultimate highly precise measurement of smaller size gears in the lab or on the shop floor - no foundation required.
-
product
Resolvers
Resolvers are electromechanical devices that convert mechanical motion into an electronic signal. Being analog devices, resolvers have no onboard electronics making them ideal for high shock, vibration and other harsh environments. Harowe offers frameless resolvers also known as servo resolvers or pancake resolvers consisting of a rotor assembly that is shaft mounted and a stator assembly that is mounted to the customer's device or housing as well as shafted housed resolvers with flange, servo groves and c-face mounts.
-
product
Wind Speed Anemometers
Comptus A75-101 and A75-104 Wind Speed measurement anemometers are built with durable injection molded polycarbonate rotors and housings, and utilize a fully hardened beryllium copper shaft.
-
product
Machinery Fault Simulator
MFS-MG MAGNUM
The MFS-MG fitted with a resonance kit is the perfect tool to gain practical experience in rotating machinery resonance and to learn resonance mitigation methods. With a different number of rotor disks installed at various locations on the main shaft, resonances up to the third mode can be excited. The bode plot of the main shaft vibration during a coast down test is illustrated in the right figure.
-
product
Rotary Switches
Reliability and ruggedness are just two of Elma's core competencies for rotary switches. Panel and shaft sealing up to IP68 against dust and water are standard for all rotary switches. The shaft material for all switches is stainless brass or stainless steel – this is suitable for rugged environments. In order to guarantee years of undisturbed functionality and service life of the rotary switches, all electronic contacts are plated and provided with hard gold. In addition to a large selection of encoders, coding switches, selector switches, audio solutions and multifunctional rotary switches, Elma Electronic offers you also the right knobs and caps.
-
product
3 Channels, 0.5 VA @ 28 Vrms
DSK
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
