Filter Results By:
Products
Applications
Manufacturers
Board Test Fixtures
jigs which hold, align and engage pcb with test interconnect.
See Also: Fixtures, Test Fixtures, Bare board Fixtures, PCB Test Fixtures, Genrad Fixtures
-
product
Functional Test Fixtures
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
product
In-Circuit Test (ICT) Fixtures
At Forwessun we support and manufacture In-Circuit Test Fixtures for a range of Test Systems. We regularly build fixtures that are supported on a range of systems including - - HP3070- Agilent- Keysight- GenRad- TeradyneWith over 50 years in the industry, we provide a weatlth of knowledge and support to our customers. We are a global company and can support businesses all over the world with the help of over 30 experienced test engineers.
-
product
EFT Module for Teststand
The Electronics Functional Test (EFT) Module for TestStand provides out-of-the-box tools to speed up development of automated tests for electronic assemblies including PCBAs, subassemblies and final assemblies. Test engineers can develop, deploy and execute test sequences quickly and efficiently with minimal custom code development for a shorter time-to-solution.
-
product
Test Solutions
Our range of test solutions is far reaching, comprised of off-the-shelf test instruments and interfaces, standard automated test systems, and custom solutions for test, simulation, and training. Put our E2E focus and experience to work for you with these solutions: automated test equipment, maintenance trainers, and test management software.
-
-
product
Tactical Radio Test Set
CTS-6010
The CTS-6010 brings an entire test bench to your front lines. Enable your technicians to detect equipment faults and verify operational capabilities at the I- and O-levels, saving valuable diagnostic time and cost.
-
product
PXI Express Optical FPGA Board
HSS-8324
The Conduant HSS-8324 Optical FPGA board provides the user with a hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its 24-lane optical interface. The PXIe interface provides a theoretical maximum throughput of 8GB/s (simultaneous in and out).
-
product
FPGA Boards
Take advantage of FPGA cards built on open standards and with a high degree of configurability in order to address a wide range of applications - without the expense and extensive development time of custom in-house developments.
-
product
FPGA Board
VP889
The VP889 is a high-performance FPGA processing board featuring Xilinx® Virtex Ultrascale+™ and Zynq® Ultrascale+™ technology.
-
product
FPGA Processing Board
VP880 / VP881
The VP880 / VP881 is a high-performance FPGA processing board featuring Xilinx® Ultrascale™ and Zynq® Ultrascale+™ technology. It is designed for the most demanding, mission critical military/defense applications such as electronic warfare / DRFM, radar/sonar image processing, satellite communications systems, multichannel digital transmission/reception and advanced digital beamforming.
-
product
Qseven® Reference Carrier Board
Q7-BASE
Qseven is a Computer-on-Module (COM) standard for small sized and highly integrated systems adopted by SGET. The Qseven concept is an off-the-shelf, multi-vendor, Computer-on-Module that integrates all the core components of a common PC and is mounted onto an application specific carrier board. Qseven modules have a standardized form factor of 70 mm x 70 mm or 40 mm x 70 mm and have specified pinouts based on the high-speed MXM connector, regardless of the vendor. The Qseven module provides the functional requirements for an embedded application, which include, but are not limited to, graphics, audio, mass storage, network and multiple USB ports. A single ruggedized 230 pin MXM connector provides the carrier board interface to carry all the I/O signals to and from the Qseven module. This MXM connector is a well-known and proven high-speed signal interface connector that is commonly used for -PCI Express graphics cards in notebooks.
-
product
Analog-to-Digital Converter Board
VME-3125A
Isolated Scanning 12-bit 32-Channel Analog-to-Digital Converter Board (6U) with Built-in-Test (BIT)
-
product
SMARC 2.1 Reference Carrier Board with M.2 Extension
I-Pi SMARC Plus
The I-Pi SMARC Plus is small (110mm x 110mm) SMARC reference carrier board based on SGeT SMARC (Smart Mobility ARChitecture) 2.1 hardware specification. Together with the SMARC short size module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
product
Quad QSFP28/QSFP+ FMC+ Module
iWave’s QSFP28/QSFP+ 2×1 Stacked FMC+ HSPC Module is designed to meet VITA 57.4 FMC+ Standard. This FMC+ Module is supported by two stacked QSFP28/QSFP+ ports(Upto400G) with 4-Bit Silicon Labs programmable clock synthesizer (default = 156.25Mhz). A flexible reference clock for on the QSFP28/QSFP+ 2×1 Stacked FMC+ Module is fully programmable over the 0.16 to 710 MHz range through I2C. Each QSFP28/QSFP+ ports are directly connected to four multi-gigabit serial transceivers banks of Vita 57.4 compliant carrier Board.
-
product
Cyclone V based 6U cPCI COTS Module
iWave’s Cyclone V based 6U cPCI Card is a rugged standalone module complaint with 6U size CPCI PICMG 2.0 Rev 3.0 backplane, aimed for the high-speed data, video processing, and display applications. The card offer speed up to 512MB/s of DMA transfer and up to a 6 channels of transceiver interfaces capable of operating up to 6 Gbps, SFP, Built-in health monitoring circuits, DVI Input, and Output Interfaces
-
product
FMC Add-On Cards
iWave’s FPGA-IP Evaluation Add-On FMC Card is designed to meet ANSI/VITA 57.1 FMC Standard. The card supports both High-Pin Count (HPC) & Low-Pin Count (LPC) connector and can be used in an air-cooled environment. FPGA-IP Evaluation Add-On Card can be interfaced with most of the FPGA development kits available in the market. This card also helps to evaluate iWave’s proprietary FPGA Intellectual Property (IP) Cores.
-
product
PCI-8 AE Board
The PCI-8 is an 8-channel, PCI-based AE system on a board. Its 8 high-speed AE channels offer simultaneous AE data acquisition, waveform processing and data transfer. The board’s standard PCI form factor enables installation in standard PCs, as well as in any of Physical Acoustics’ specialized AE system chassis, while the PCI bus enables AE data transfer at speeds of up to 132 Mb/s, at a frequency range of 1 kHz to 400 kHz.
-
product
PCI Three-Axis High Performance Laser Board with External Sampling
N1231B
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
product
PCI Three-Axis Laser Board
N1231A
The Keysight N1231A PCI Three-Axis Laser Board is a register based PCI bus board that implements three axes of laser measurement for position monitoring and closed-loop servo control. The hardware outputs, optimized for connection to a DeltaTau PMAC servo control system, provide parallel digital position data at rates up to 4MHz. The same position data along with velocity data is available over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
product
Computer On Module
ITX-M-CC452-T10
The ITX-M-CC452-T10 is an industrial Mini-ITX small form factor Type 10 reference carrier board designed to fully test WINSYSTEMS’ COMeT10-3900 COM Express Type 10 Mini module. The carrier board adheres to the PICMG COM Express specifications providing compatibility with other COM Express mini type 10 modules.
-
product
COM Express Type 6 evaluation carrier board
ATX-M-CC462-T6
The ATX-M-CC462-T6 is a fully featured COM Express Type 6 evaluation carrier board designed for use with the WINSYSTEMS Intel® Tiger Lake UP3 COM Express and other COM Express Type 6 modules.
-
product
3U CompactPCI® Single 64-bit PMC Slot Carrier Board
cPCI-8301
*PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus*Supports one single-size 32,64-bit/33,66 MHz PMC site in 4HP width*Universal V(I/O) decided by backplane*Comprehensive EMC shielding
-
product
3U CompactPCI Mini PCI, Mini PCIe Carrier Board
cPCI-3W10
*Supports 32bit, 33/66MHz CompactPCI® bus*One SIM card socket*One Mini PCI and one Mini PCIe socket*PICMG® 2.0 R3.0 compliant
-
product
34945EXT Distribution Board, For Two 87222, L7222C Transfer Switches And Six N181x SPDT Switches
Y1154A
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
product
M/MA Module Carrier
VX405C
The VX405C carrier provides the mechanical and electrical interfaces between the VXIbus and up to six (6) VITA 12-1996 standard M/MA-Modules. The carrier provides VXI register configuration and access to the M/MA-Module I/O space and memory (if present). Each M/MA-Module is controlled separately and appears as a different logical address in the VXI environment. Over 100 M/MA-Modules are available that can provide custom interfacing to the unit under test (UUT). Up to six (6) unique interfaces may be provided in a single VXI slot.
-
product
PCI Express 5.0 Test Platform
Teledyne LeCroy’s PCI Express 5.0 Test Platform is part of a suite of tools that facilitates complete protocol testing of PCI Express devices up to and including version 5.0. The latest feature of the Teledyne LeCroy Test Platform is the addition of an integrated interposer, which eliminates the need for an external interposer. This innovation simplifies setup with fewer connection points and outboard devices, making analysis easier and more reliable than ever. In addition to using the Test Platform with the Exerciser, the user can connect two of their own devices and use the Test Platform as a PCIe 5.0 backplane and as an interposer to capture protocol traffic between the systems.
-
product
PCIe 5.0 Test Platform
PXP-500A
The Teledyne LeCroy PXP-500A Test Platform provides a convenient means for testing PCIe 5.0 cards with a self-contained portable and powered passive backplane. The PXP-500A provides power required for both cards under test.
-
product
ARINC 818 Tester
iWave 3U VPX High-Speed Video/Data Processing Card is a rugged standalone module in the 3U VPX form factor, aimed for the high-speed data, video processing, and display applications is ideal for military, defense, and aerospace applications requiring an optimal balance of performance and power efficiency. iWave 3U VPX High-Speed Video/Data Processing Card is implemented using Xilinx Kintex-7 device architecture and has I/O interfaces including High speed 16 channels of transceiver interfaces capable of operating up to 6 Gbps data rate, Gigabit Ethernet, RS232, RS422, PCIe interface, Built-in health monitoring circuits, HDMI input, and output interfaces
-
product
Automatic Test System
Automatic Test system is the ultimate solution for power electronic testing. The system includes a wide range of hardware choice such as AC/DC Sources, Electronic Loads, DMM, Oscillate Scope, Noise Analyzer and Short /OVP Tester. This flexibility combined with its open architecture software platform-PowerPro III, gives users a flexible, powerful and cost effective test system for almost all types of power supply testing.
-
product
SoC Test System
Specifically designed for high-throughput and high parallel test capabilities to provide the most cost-effective solution for fabless, IDM and testing houses. With the full functions of test capability, high accuracy, powerful software tools and excellent reliability, 3650-EX is ideal for testing consumer devices, high-performance microcontrollers, analog devices and SoC devices.
