OMICRON electronics
Specialization in power system testing.
- 1-800-OMICRON
1-713-830-4660 - 3550 Willowbend Blvd
Houston, TX 77054
United States
-
product
12 kV Insulation Fluid Test Cell
CP TC12
The CP TC12 oil test cell is for determining the relative permittivity, the dissipation factor and the power factor of insulating liquids such as transformer oil.
-
product
3-in-1 Test System
CIBANO 500
CIBANO 500 combines a micro-ohmmeter, timing analyzer, and a coil and motor supply. All important CB tests on all types of CBs can be carried out even when a station battery is not available.
-
product
Binary Input/Output Terminal
ISIO 200
ISIO 200 is a simple and versatile binary I/O terminal with IEC 61850 interface. For communicating with CMC test sets and real-time message exchange with peer devices, the fast GOOSE messaging is used. By using Client/Server communication, ISIO 200 can be integrated into Substation Automation Systems (SAS) and communicate to a station controller.
-
product
CMControl P
CMControl P is a control option for CMC test sets, specially designed for the quick manual testing of protection and measurement devices.
-
product
CMC test Set Extender
RXB1
RXB1 extends CMC test sets with 4 additional binary relay outputs. Each binary output channel consists of a normally open ("make") and a normally closed ("break") contact.
-
product
Companion for on-Site Testing
PTMate
The PTMate app is our mobile companion for the Primary Test Manager™ (PTM) software. It supports you on site by providing additional features on your smartphone, for example, sending images, displaying wiring diagrams, or sharing jobs and reports.
-
-
product
Current Transformer Analyzer
CT Analyzer
Current transformer testing in a multifunctional instrument performing excitation, ratio, polarity and winding resistance tests on current transformers as well as burden impedance measurement.
-
product
Dielectric Insulation Analyzer
DIRANA
DIRANA uses dielectric frequency response (DFR) analysis in order to determine the condition of high-voltage insulation systems such as those in power transformers, bushings, cables and generators.
-
product
Handheld Grounding Tester
HGT1
The HGT1 is a handheld meter to measure ground impedance as well as step and touch voltages. Using the CPC 100 and CP CU1, test currents at variable frequencies can be fed into power cables or overhead lines safely to simulate a ground fault.
-
product
Hybrid Signal Analyzer
DANEO 400
DANEO 400 is a hybrid measurement system that records and analyzes all conventional signals (voltages, currents, hard wired binary status signals) and messages on the communication network in a substation.
-
product
Mobile, Hardened Test Set
MBX1
With the MBX1 platform and our software, you can easily test SCADA and substation automation systems (SAS) in a highly secure way. The mobile solution allows you to perform quick assessments and temporary monitoring, e.g. during commissioning.
-
product
Partial Discharge Measurement and Analysis System
UHF 800
Our UHF 800 is a system for measuring and analyzing partial discharges in the ultra-high frequency (UHF) range in testing environments with high levels of external noise.
-
product
Partial Discharge Measurements
MPD 500
The MPD 500 simplifies routine factory partial discharge measurements for electrical insulation systems. Engineered with OMICRON's long time experience, the MPD 500 is optimized for routine tests in high throughput environments.
-
product
Portable Protection Test Set and Calibrator
CMC 430
The CMC 430 is the preferred choice for test engineers in cases where excellent transportability is needed and three currents up to 12.5 A or six voltage outputs are sufficient. Its low weight of just 8.7 kg / 19.2 lbs, and robust design with its edge protection predisposes the device to every outdoor and indoor use.
